Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Amplifier Built-in Ultra-slim Photoelectric Sensor
EX-10S
-
Panasonic Industrial Devices Sales Company of America
Like the EX-10 Series, with the dimensions of only 14.5 x 3.5 x 10mm, the EX-10S Series Amplifier Built-In Ultra-Slim Photoelectric Sensors are among the smallest and narrowest Sensors worldwide. This "S" version with a thinner beam allows the detection of small objects within a very narrow detection zone.
-
Product
4 Channel 24.5~ 29.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808
-
The UC INSTRUEMNTS CA9808 4 Channel 24.5 ~ 29.0 Gb/s (100Gb/s) Pulse Pattern Generator and Error Detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 24.5 Gb/s to 29 Gb/s each Channel. 4 channel 29.0 Gb/s make it total up to over more than 100 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
High-Voltage Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Measurement of DC or AC voltages up to () 3600 V and of large DC currents to about () 20 kA with shunt resistor or directly in the device to () 5A DC and AC. Variants with calibrated range selection.
-
Product
Digital Delay / Pulse Generator
DG535
-
Stanford Research Systems, Inc.
The DG535 Digital Delay and Pulse Generator provides four precisely-timed logic transitions or two independent pulse outputs. The delay resolution on all channels is 5 ps, and the channel-to-channel jitter is less than 50 ps.
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
Dual Channel High Voltage Linear Amplifier
A400D
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply.
-
Product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
-
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
Product
Premium Headphone Amplifier
A 2
-
A premium model with a discrete configuration and full analog circuit that was created to drive the T 1 thoroughly.
-
Product
RF Amplifier
MLE-02-1G
-
Hangzhou Softel Optic Co., Ltd.
MLE-02 is kind of bidirectional amplifier with one input port and one output port, which forward gain range from 28dB to 41dB and the max gain of reversed path can reach 23dB. It can be used as a trunk amplifier in the traditional coaxial network, also it can be used as an line extender amplifier in the HFC network. Its tank-type construction is convenient for maintenance.
-
Product
Third Party RF Amplifiers
-
We work closely with major manufacturers to supply a range of oscilloscopes, function generators and power amplifiers. We are the UK agent for the leading manufacturer of RF amplifiers Electronics and Innovation.
-
Product
Single And Dual 32k Digital MCA & Pulse Processor
Hexagon Family
-
Hexagon is a high precision 32k MCA available in single and dual input channel versions. This compact, high performance desktop MCA includes features such as an input stage for signal conditioning, a fast analog-to-digital converter (ADC), digital signal processing algorithms, High Voltage and Preamplifier outputs for detector bias and preamp power. Hexagon is ideally suited for applications using high energy resolution semiconductor detectors such as HPGe, Silicon, CZT as well as scintillation detectors such as NaI and LaBr3. It can manage both positive and negative signals from resistive feedback or transistor reset preamplifier detectors as well as signals coming from PMT anodes.
-
Product
Amplifiers & Signal Processors
-
Power for Core Technology Group Signal Chain ProductsFlexible bi-polar voltage converter using low cost connectorsDriving multiple devicesIndustrial +/- 10 volt power source
-
Product
Four Quadrant Power Amplifier For Simulation Applicaton
PAV30000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800B (2RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800B (2RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
120 A Manual Pulse Width Extender
TLP-12012A6
-
High Power Pulse Instruments GmbH
- Pulse width extender for the high current TLP/HMM test system TLP-12010A and TLP-12010C- 6 manual selectable pulse width: 5, 10, 50, 100, 200 and 500 ns- High pulse output current up to ±120 A- High performance and high quality components
-
Product
RF High Power Amplifier Modules
-
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
Product
DR Range Broadband Power Amplifiers 10 KHZ - 400 MHZ
DR Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 400 MHzTypical output power : 60 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 40 W and H<-20 dBc up to 250 MHz andP1dB > 25 W and H<-20 dBc from 250 MHz to 400 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
Product
Medium & High Voltage Pulse Generators (Rise Time > 1 ns)
-
Offer fast medium voltage pulsing with high current capability. These models are ideal for driving solenoids, pulse testing of MOSFETs, and other applications.
-
Product
Amplifier
AC-100
-
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
Product
ADC Drivers Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
Microwave Power Amplifier 10W 100 MHz to 20 GHz
GT-1000B
-
The Spanawave GT-1000B Microwave Power Amplifier offers linear high-power amplification across multi-octave bands. It is ideal for testing in EMC, wireless communications applications and Defense EW systems. For EMI/EMC and standards laboratories, the GT-1000B with 100 MHz to 20 GHz frequency range allows broadband testing without band switching or swapping narrow band amplifiers resulting in faster and more accurate testing.
-
Product
Semiconductor Power Amplifiers : Solid State Power Amplifiers (SSPA) For Indoor (rack-mount) And Outdoor (hub-mount) Settings
-
Insight Product Company is proud to offer state-of-the-art semiconductor (solid state) power amplifiers that are compact, rugged, and deliver immense power, and expectional frequency stability and minimal phase noise. These solid state power amplifiers are ideal for indoor, rack-mount, or outdoor, hub-mount, applications. We offer S-band, C-band, X-band, and Ku-band amplifiers, with output power of upto 1,000 Watts (varies based on frequency band).
-
Product
Low Noise Amplifiers
-
Electronic component that amplifies a very low-power signal without significantly degrading its signal-to-noise ratio (SNR).
-
Product
System Amplifiers
-
The perfect combination of high performance, wide bandwidth and low noise
-
Product
Peripheral Differential Amplifier
-
The Peripheral Differential Amplifier (PDA) module allows the simultaneous recording of differential bipolar high-ohmic external voltages, such as reference or pH meters. The PDA has 8 differential input channels, and it is stackable up to units with a total of 64 channels. The PDA module is powered from the grid via an adapter.
-
Product
Fiber Optic Sensor & Amplifier
FG-1300 | FS-5500/FS-540
-
The FG-1300 is a non-contact type high-performance amplifier that emits red light from LED to a rotating object, and detects the variation of the reflected red light amount.This amplifier is used in combination with an exclusive detector FS-5500*/FS-540 Fiber Optic Sensors which has adopted environment resistant design. The glass fibers are covered with flexible stainless steel tube for rotation measurement in limited space.
-
Product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
-
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
IEPE Signal Conditioning Amplifiers
-
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
