-
Product
T3/E3, OC3/OC12, & STM1/STM4 Testing
-
T3 E3 Analysis software compliments the hardware and supports simultaneously monitoring up to 12 x T3 E3 lines (2x Rack units) for all alarms, frame errors, signalling and data. If one adds the Channelized T1 Analyzer software to the system, then the T1s within the T3s can also be analysed in software, 12 x T3 E3 lines (=12*28 T1s) constituting 336 full duplex T1s, or 672 simplex T1s monitored simultaneously using a single Rack unit.
-
Product
T3 Low & High Voltage Differential Probes
T3 Series
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
Multifunction Electrical Installations Meter
MPI-525
-
Possible measurementsShort-circuit loop measurement:*impedance measurement with 23 A current (44 A phase-to-phase) - short-circuit resistor R=10,*measurement range: 95...440 V, frequency 45...65 Hz,Short-circuit loop measurement with resolution 0,01, in distribution network without tiggering RCD (In30 mA):*automatic calculation of short-circuit, detection of phase voltage and phase-to-phase voltage,*additional UNI-Schuko plug for automatic measurement, AGT adapter for 3 phase network measurement.Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA. (Type AC, A and B).Measurement of insulation resistance:*with test voltage 250 V, 500 V, 1000 V, 2500 V,*measurement range up to 10G,*automatic discharging after measurement,*automatic measurement of all resistences in 3,4,5-wire cables using optional adapter AUTO-ISO,*acoustic signals in 5 sec intervals for insulation resistance characteristic,*elapsing T1, T2, T3 times (0...600 s) form measurement of absorption coefficients (DAR, PI or Ab1, Ab2)*safety measurement - protection against overvoltage.Measurement of earthing resistance.Bi-directional testing of PE wire continuity using 200 mA current.*Autocalibration of test leads.
-
Product
WAN Tester III
-
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
Product
WAN Tester lllD
-
It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems, multiplexers, CSU/DSUs, T-1 CSUs, DDS CSUs, DDS CSU/DSUs, DTUs, NTUs and TIUs. The Ds3 tester is supplied with user-changeable nickel metal hydride batteries and a built-in charger.
-
Product
Analog Platforms
(T1/E1/T3/E3/OC-3/OC-12/STM-1/STM-4)
-
Almost all T1 E1 T3 E3 Testers can be accommodated into rack-based units. Multiple rack units can be stacked together for greater scalability. Shown below is a rack based tProbe™ T1 E1 / T3 E3 Analyzer unit, and a Channelized T3 E3 Analyzer unit supporting 6 T3s (6 * 672 DS0s). Such customized rack serves the purpose of handling multiple communications lines and test complex functionalities.
-
Product
Test, Map, Profile and Qualify "Dark" Coax Cable Networks
Coax Clarifier
-
Dark unpowered coax systems give no clue as to their design, condition or configuration. The new Coax Clarifier by T3 Innovation makes it simple and easy to discern the layout of a coax network, locate faults on individual cable runs, identify remotes through splitters, and determine cable run length. In addition, separate wiremapping sets allow a technician to map out the entire coax system and measure the quality and characterization of the overall network for carrying services, such as high grade video, surveillance data and HD programming.
-
Product
Ultra Portable SuperSpeed USB Analyzer
Advisor T3
Analyzer
Teledyne LeCroy’s Advisor T3 is an ultra portable SuperSpeed USB analyzer that delivers market leading accuracy at an extraordinary price. Designed to put precision USB protocol test tools in the hands of every engineer, the Advisor includes all the essential features for SuperSpeed USB debug.
-
Product
Exhaust Gas Thermocouple
LM2500 T5.4
-
AMETEK is the original OEM for the T5.4 EGT. We supply the L44830P01, L44830P02 and L44830P03 probes for use on the LM2500, LM2500+ and LM5000 gas turbines. In addition to the EGT, we also provide rigid harness, T3 probes, cables and flexible harness for these engines. Ensure you get the highest quality by selecting OEM qualified parts to keep your engine running reliably.
-
Product
PCIe 3.0 Protocol Analyzer
Summit T3-16
Protocol Analyzer
The Summit T3-16 is Teledyne LeCroy's fifth generation of protocol analyzers targeted at high speed PCI Express I/O-based applications such as workstation, desktop, graphics, storage, and network card applications.
-
Product
4.5 Digit, 150 Meas/Sec True RMS Digital Multimeter
T3DMM4-5
Digital Multimeter
4.5 Digit, 150 Meas/Sec True RMS Digital Multimeter.
-
Product
Arbitrary/Function Generator,2 Ch,8-DIG ch, 150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing
T3AWG2152-D
Function Generator
Arbitrary/Function Generator,2 Ch,8-DIG ch, 150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing.
-
Product
Arbitrary/Function Generator,2 Ch,150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing
T3AWG2152
Function Generator
Arbitrary/Function Generator,2 Ch,150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing.
-
Product
Compressed Air RH+T+Tdp Sensor
T3111P-4
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
AC/DC Single Phase Digital Power Meter 6 kHz
T3PM1006
Power Meter
AC/DC Single Phase Digital Power Meter 6 kHz.
-
Product
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A
T3PS23203
Power Supply
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A.
-
Product
40 MHz, 1.2 GS/s, 8 Mpts, 2 Ch, 20 Vpp Function/Arbitrary Waveform Generator
T3AFG40
Arbitrary Waveform Generator
Teledyne Test Tools T3AFG5 and T3AFG10 series Function/Arbitrary Waveform Generators are a new family of low cost, high performance, single channel Function / Arbitrary waveform generators offering a high level of functionality and an excellent specification at a very competitive price point.
-
Product
PCIe 3.0 Protocol Analyzer
Summit T3-8
Protocol Analyzer
PCIe 3.0 technology achieves twice the effective data throughput rate of the PCIe 2.0 standard through a combination of increased data bit rate (5 GT/s moving to 8 GT/s) and the elimination of 8b/10b data encoding, which previously added an overhead of 20 percent to all data transfers. In eliminating 8b10b encoding, PCIe 3.0 technology now relies on the existing data scrambling techniques similar to those used for PCIe 2.0 technology to ensure that receivers maintain lock on the incoming data stream.
-
Product
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A
T3PS11230
Power Supply
Bench Power Supply, Switching DC, Adjustable, 1 Output, 0 V, 12 V, 0 A, 30 A.
-
Product
80 MHz, 1.2 GS/s, 8 Mpts, 2 Ch, 20 Vpp Function/Arbitrary Waveform Generator
T3AFG80
Arbitrary Waveform Generator
Teledyne Test Tools T3AFG5 and T3AFG10 series Function/Arbitrary Waveform Generators are a new family of low cost, high performance, single channel Function / Arbitrary waveform generators offering a high level of functionality and an excellent specification at a very competitive price point.
-
Product
Low & High Voltage Differential Probes
T3
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
AC Current Probe 20 mV/A, 300A, 9.2 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable
T3RC0300-UM
-
AC Current Probe 20 mV/A, 300A, 9.2 Hz LF Bandwidth, 30MHz HF Bandwidth, 1m cable.
-
Product
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse
T3CP50-50
-
50A, 50 MHz CURRENT PROBE, BNC, AC/DC, 50A rms, 75A Peak Pulse.
-
Product
AC/DC Single Phase Digital Power Meter 100 kHz
T3PM1100
Power Meter
AC/DC Single Phase Digital Power Meter 100 kHz.
-
Product
1500W Single Channel 19", 1U, Rack Mounted DC Power Supply
T3PS60251P
DC Power Supply
1500W Single Channel 19", 1U, Rack Mounted DC Power Supply.
-
Product
D.C Milli-Ohm Meter, 4-Wire with Handler/RS-232C/USB Device
T3MIL50
-
D.C Milli-Ohm Meter, 4-Wire with Handler/RS-232C/USB Device.
-
Product
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse
T3CP500-5
-
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse.
-
Product
Digital Multimeters
T3DMM Series
Digital Multimeter
Teledyne Test Tools new T3DMM series are dual display digital desktop multimeters that provide a rich and powerful feature set. The design is easy-to-use from the front-panel and computer-based control via USB or LAN. Each model is equipped with a 4.3 inch TFT-LCD true color screen with 480 * 272 resolution for easy viewing. The T3DMM series also features numerical data display, histograms, trend charts, bar charts and statistics, in addition to the built-in arithmetic functions including Measurement statistics.
-
Product
16 Channel, Single Slot, Bench Data Acquisition Unit with 6.5 Digit DMM
T3DAQ1-16
-
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes. Includes Spring Tip, tip protector, and standard accessories package.
-
Product
D.C Milli-Ohm Meter with Advanced Features, 4-Wire, Handler/RS-232C/USB Device/GPIB
T3MIL50X
-
D.C Milli-Ohm Meter with Advanced Features, 4-Wire, Handler/RS-232C/USB Device/GPIB.
