Electromagnet
See Also: Electromagnetic
-
Product
Finite Element Method Magnetics Simulation Software
FEMM
-
Finite Element Method Magnetics
FEMM is a suite of programs for solving low frequency electromagnetic problems on two-dimensional planar and axisymmetric domains. The program currently addresses linear/nonlinear magneto-static problems, linear/nonlinear time harmonic magnetic problems, linear electrostatic problems, and steady-state heat flow problems.
-
Product
High-frequency Induction Heater Unit
-
High-frequency induction heater unit is a high frequency generator for non-contact heating of metal using electromagnetic induction.
-
Product
CE Marking
-
Only safe, flawless, and quality goods should be available on the European market – at least, that’s the objective of the CE mark. The mark proves that the product in question conforms to EU health and safety standards, whether it's toys or construction machines. Our experts conduct an audit on your products based on the appropriate EU regulations, such as the low-voltage or electromagnetic compatibility directive. Your CE declaration of conformity means your product now has right of way onto the European market.
-
Product
Electrodynamic Shakers | Electrodynamic Shaker Systems
-
Wewon Environmental Chambers Co, Ltd.
Your product descElectrodynamic shakers makes use of an electro-mechanical assembly to product vibration through electromagnetic force. These electrodynamic shaker systems can precisely generate either single, or multi-axis vibration using sine, random, sine-on-random, or random-on-random accounts. Usually these ED shakers are utilized to figure out the products ability to either run within it’s intended environment, or to target resonance in the product to determine weakness.Any type of product moved by road, sea or air, is subjected to vibration tests throughout its manufacturing procedure. These tests supply essential details relating to the behavior of the manufactured part before advertising and marketing, in order to prevent them breaking in the future.All the vibration tests, both vertical and also horizontal, may furthermore go through temperature as well as relative humidity tests, integrating the vibration test with making use of a climatic chamber. The electro dynamic shakers from Wewon attach to any kind of electrodynamic vibration system. https://www.wewontech.com/electrodynamic-shakers/
-
Product
Gauss Meters
-
A gauss meter displays electromagnetic wave measurements in Gauss (G), milliGauss (mG), milliTesla (mT) or microTesla (µT) units. A gauss meter can detect either static (DC) permanent (rare-earth) magnetic or dynamic (AC) electromagnetic fields (EMFs), or both. Thus, it is important to review the specifications of a gauss meter prior to purchase to ensure suitability for the intended application.Neodymium (NdFeB) permanent magnets are among the world's strongest and most widely used magnets. When testing magnets made of neodymium or other rare-earth elements, a gaussmeter or magnetometer capable of measuring DC magnetic fields is required. However, most electromagnetic fields encountered are generated by AC currents. Examples include electrical power lines, transformers and wiring for overhead lighting, solar panels and other electrical devices and equipment. Electromagnetic fields from electrical installations are believed to cause feelings of nervousness, anxiety and paranoia in EMF-sensitive human beings.Most gaussmeters offered by PCE Instruments can be calibrated and certified according to DIN ISO 9000 standards for an additional fee. Replacement gaussmeter probes and optional accessories are available for most gaussmeter models.
-
Product
Advanced Design System (ADS) Core
W2200BP
-
Advanced Design System (ADS) is the flagship product from Keysight EEsof EDA, the technology and innovation leader in high-frequency, mixed-signal electronic design automation (EDA). It is the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. ADS seamlessly integrates system, circuit, and full 3D electromagnetic simulation with Keysight's test instrumentation to perform single pass successful electronic designs repeatedly.
-
Product
Dielectric Probe Kit
N1501A
Accessory Kit
The Keysight N1501A dielectric probe kit with N1500A materials measurement software suite with Option 004, and a Keysight network analyzer, determines the intrinsic electromagnetic properties of many dielectric materials. Because these properties are determined by the molecular structure, they can be related to other properties of interest as well. Measuring them can provide critical insight into applications in many industries.
-
Product
Data Loggers
-
Data loggers are small electronic devices used to track and store location-specific data via built-in or external sensors. They are typically battery-powered and equipped with internal memory, and have become the predominant method of monitoring in most contemporary industries, having increasingly replaced the electromagnetic chart recorders that originated back in the early 19th
-
Product
Electromagnetic (EM) Speed Log System
AGILOG 2
-
Aeronautical & General Instruments Ltd.
Developed for use on surface warships and submarines, AGILOG 2 sets the standard for accurate and reliable measurement of ship’s speed through the water, an essential element in navigation and weapons system integration.
-
Product
Flow Management
HR7100
-
HighReach Measuring & Controlling System Co.,Ltd
HR7100 series intelligent electromagnetic flowmeter is a fully intelligent flowmeter developed and developed by our company using the most advanced technology at home and abroad. It has the characteristics of high measurement accuracy, high reliability, good stability and long service life. Pay attention to every aspect In the process of designing product structure, material selection, manufacturing process, production assembly and factory testing. We have a water tower of up to 35m as a steady-state flow regulator, as well as a professional electromagnetic flowmeter production equipment line. Designed and developed large-scale production software and hardware for electromagnetic flowmeters to ensure long-term high quality.The product is designed with Chinese and English liquid crystal display with wide backlight and full-featured function. It is intuitive to display, easy to operate and use, and can reduce the trouble of on-site installation and maintenance. Widely used in petroleum, Chemical, metallurgy, water supply and drainage, steel, coal, paper, food, textile, environmental protection and other industrial sectors and municipal management, water conservancy construction and other fields.
-
Product
Fiber Optic Strain Sensors
-
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
Product
FCC-Recognized Accredited Testing & Certification
-
Helping you ensure that your radio devices or devices with integrated wireless modules meet requirements to demonstrate compliance to FCC requirements for approval.Manufacturers planning to sell their wireless/RF products in the United States must ensure that their equipment won’t electromagnetically interfere with other products or cause harm to the public as enforced by the Federal Communications Commission (FCC), per Title 47 of Code of Federal Regulations (CFR).
-
Product
EMC & EMI Filters
-
CTS is the leader in EMI/RFI filters and offers a diverse product line of standard as well as custom filters to suppress electromagnetic interference (EMI) / radio frequency interference (RFI), thereby providing customers with a wide range of electro-magnetic compatibility (EMC) solutions. Discover cutting-edge solutions for your electromagnetic compatibility needs with CTS EMC products. Our innovative range is engineered to deliver unparalleled performance, ensuring seamless connectivity and optimal functionality across diverse industries.
-
Product
CW (Continuous Wave) Magnetrons For Industrial Microwave Heating
-
Insight Product offers CW magnetrons models for industrial and commercial microwave heating, the frequencies 915 MHz and 2450 MHz with output power up to 100 kW. We offer these CW Magnetrons together with accompanying solenoids, based on Permanent magnet or Electro-Magnet depending on model.
-
Product
High-speed Photodetectors
11HSP
-
Only gigahertz-bandwidth qualified components are used in those high-speed photodetectors. An impedance matched microstrip line is used to couple the diode's output to the output connector. A microwave quality SMA electro-magnetic wave launcher is used to couple the signal to the scope.
-
Product
EMI/EMC Compliance Consulting
-
EMI Devices offers a broad range of consulting services in the field Electromagnetic Compatibility. Our extensive knowledge of consumer electronics and worldwide regulatory requirements allow us to design Electromagnetic Compatibility Regulatory Compliances from the start.
-
Product
Transducers For Photodiodes
-
Photodiodes convert incoming electromagnetic radiation into electrical charge carriers. If photodiodes are short circuited an electrical current (photocurrent) proportional to the incident radiation intensity (number of photons per second) is induced. These photocurrents are generally small and cover the range from femtoampere (fA) to microampere (µA). Signal transducers transform this weak photocurrent to robust standard signals for reliable data transmission and simple data acquisition.
-
Product
Clarity 3D Solver
-
The Cadence Clarity 3D Solver is a 3D electromagnetic (EM) simulation software tool for designing critical interconnects for PCBs, IC packages, and system on IC (SoIC) designs. The Clarity 3D Solver helps designers tackle the most complex electromagnetic (EM) challenges when designing systems for 5G, automotive, high-performance computing (HPC), and machine learning applications with gold-standard accuracy.
-
Product
Radiation (EMF, Nuclear, RF)
-
Sper Scientific radiation meters measure EMF, Nuclear, and Microwave radiation levels. Whether you are, measuring the RF strength of Wi-Fi and LAN network, or the electromagnetic field emissions from electrical power lines and transmission equipment, computers, HVAC, audio/video, and other electrical appliances. Our meters are small and light enough to go anywhere, yet sensitive enough to detect minuscule amounts of gamma, beta or X-rays.
-
Product
EMC/EMI
-
Electromagnetic Compatibility (EMC) or Electromagnetic Interference (EMI) testing deals with your products’ Radio Frequency (RF) emissions and immunity to RF. EMC testing ensures that your product will operate as intended in the intended environment and it won’t interfere with other products used in its same electromagnetic environment.
-
Product
Signal Acquisition and Filtering Technology
SNAPTrack®
-
Built on a proven design, and with Pathfinder SAF Technology™ at its core, the SnapTRACK® offers RYCOM’s most advanced signal acquisition and filtering technology. The SnapTRACK® cable & pipe locator offers utility locators FrequencyFlex™ allowing users to adapt the system to their specific needs. Multiple active frequencies allow the user to accurately locate with a minimum of interference while maintaining the ability continue locating past faults and around conduit bends. Passive frequencies identify "live" and charged lines by their naturally occurring electromagnetic fields. The SnapTRACK® offers multiple passive frequencies -- 50Hz, 60Hz, Radio Frequency, Cathodic Protection Rectifier & CATV -- allowing line locating without the use of a transmitter.
-
Product
AC Load Bank (Resistive & Inductive)
K-1000 Resistive & Inductive
-
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
Product
Qwiic Spectral Sensor
AS7341
-
The AS7341 is an 11-channel spectral sensor from AMS that covers wavelengths between 350nm to 1000nm. It features eight channels that span the visible spectrum and there's a channel for Near IR, clear, and flicker detection up to 2kHz. Point a spectral sensor at an object and it measures the reflected or absorbed electromagnetic wavelengths.
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
Handheld 1-D electro-magnetic current meter for rivers
AEM1-DA
-
AEM1-DA is a 1-D electro-magnetic (EM) current meter for the flow measurements in rivers, streams and various waterways. The measurement range is 0 to 5m s-1. The EM sensor can accurately measure water speeds at a shallow depth of 3cm. The display unit has a 2MB flash memory so that the data are saved with calendar information (up to 255 station data). In comparison with conventional propeller-type current meter, AEM1-DA is robust and extremely easy to be operated and maintained.
-
Product
Compact Accelerometer (Shock Meter)
AP2019
-
Can be used as shock sensors in equipment diagnostic systems; Combination of high axial sensibility, intrinsic frequency and shock resistance; Low sensitivity to electromagnetic fields; Low intrinsic noise level.
-
Product
Accessories
-
Hunan Linkjoin Technology Co., Ltd.
Linkjoin accessories - electromagnet, core test fixture, epstein frame, DC permeameter, AC permeameter, reference magnet, magnetic flux fixture, solenoid, helmholtz coil, temperature controller, etc
-
Product
Air Core Inductors
-
Osborne designs our Air Core Inductors to realize their advantage of high linearity. We also work with our clients to identify and mitigate any potential disturbances that could result from electromagnetic fields created. The air core design approach is known to create strong electromagneticfields. Osborne develops electromagnetic circuit models, if necessary, to ensure that our clients build effective and reliable circuits.
-
Product
EMI/EMC Compliance Consulting
-
EMI Devices offers a broad range of consulting services in the field Electromagnetic Compatibility. Our extensive knowledge of consumer electronics and worldwide regulatory requirements allow us to design Electromagnetic Compatibility Regulatory Compliances from the start.
-
Product
QW-AddIn For Autodesk® Inventor® Software
-
QW-AddIn for Autodesk® Inventor® Software is a QuickWave plug-in for Autodesk® Inventor® Software, a wide-spread mechanical tool, allowing defining a complete project for electromagnetic simulation, also periodic structures and axisymmetrical structures (V2D), directly in the popular CAD environment. A set of self-explaining dialogues provides very convenient tool for setting the electromagnetic properties such as assigning the materials, adding ports, boundary conditions, setting postprocessings and excitation parameters.Automatic mesh generation using Automatic Meshing Intelligent Generation Option (AMIGO) optimises the meshing taking into account requested wavelength resolution in all media, while avoiding unnecessarily small cells. Additionally QW-AddIn for Autodesk® Inventor® Software can be used for optimisation and parameters sweep with QW-OptimiserPlus.QW-BHM is available and heating parameters can be defined together with rotation in XY plane along axis parallel to Z axis. Creating proper axis of rotation can be done by selecting edge or solid body from the project. It will contain the middle point of selected object and its location can be modified either with the mouse or by entering new coordinates.
