PCI Diagnostic Cards
See Also: POST Cards
-
Product
PCI High Density Matrix, Single 22x4 2-Pole
50-510A-022
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
PCI Express 8-Port
7804ec
-
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
Product
PCI Board
FastX1703-DIG
-
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
Product
Time Domain Reflectometer (TDR) Card
PCI-3127
-
The PCI-3127 is a PCMCIA-form factor TDR that can be used to identify and locate failures in installed wiring and cable systems. The instrument can make high resolution TDR measurements on circuits up to 96,000 feet (~30km) from your Windows XP notebook computer or PC using a low-voltage non-destructive test signal.
-
Product
PCI Express System Timer (USB Interface)
SKU-032-01
-
The MiniPCI Express System Timer uses a standard USB interface to synchronize IP signals. This system timer provides accurate clock timing for Asterisk® open-source PBX software.
-
Product
Time Interval Counter Card
GC2200 Series
Interval Counter
The GC22x0 family of PCI universal time interval counters offer many of the measurement and timing functions of high-end stand-alone frequency counters, including accumulate, auto ratio, frequency, fast frequency (GC2220 and GC2230 only), period, ratio, single period, test clock, time interval, time interval delay, totalize, totalize gated, totalize gated once, and pulse width.
-
Product
Data Acquisition PCI Card
UPC2100
-
The UPC2100 PCI Sensor Interface card provides real-world data acquisition and control for your PC. Up to 16 sensor inputs in any mix or combination are accepted by the UPC2100. No external signal conditioning is required. The UPC2100 includes configuration and data acquisition software and is compatible with C#, .NET, C++, Visual Basic, LabView.
-
Product
Sixteen Channel 12-Bit Analog Input/Output Cards
PCI-A12-16A
-
Model PCI-A12-16A is a multifunction, analog-to-digital, digital-to-analog, and digital I/O card. It accepts up to 16 single-ended inputs or eight differential inputs. Inputs are protected against over-voltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts. Conversions can be initiated in any one of three ways: (a) software command, (b) external start commands, or (c) on a timed basis using on-board programmable counters. Converted data may be transferred to the computer by one of two software selected methods: (a) polling for the end-of-conversion signal, or (b) by generating an Interrupt when the end-of-conversion signal occurs.
-
Product
Dual Port Fibre Channel End-System Module for PCI Express
PCIe-FC4-NIC
-
Avionics Interface Technologies
Dual port module, operates as a Fibre Channel network node with support for multiple upper layer protocols.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Express Module
PCIe-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
PCI 2 Amp Multiplexer, Quad 8-Channel, 1-Pole
50-635A-108
Multiplexer Module
The 50-635A-108 is a quad 8-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
8-CH 16-Bit PCI Express Analog Output Card
PCIe-6208
Analog Output Module
ADLINK PCIe-6208 series are 8-CH, 16-bit, PCI Express analog output cards which provide high resolution, high-density analog output functionalities and are suitable for ATE, signal generation, industrial process control, servo control and other industrial control applications.
-
Product
HPx-400e PCIe Radar Input Card
-
The HPx-400e is a high-performance PCI express single or dual stream primary radar acquisition card, capable of capturing and processing analogue and digital primary radar video from up to two independent radars. The dual stream HPx-400e variant supports a number of multi-channel input modes, including dual redundancy and fully independent dual-stream capture.
-
Product
Dual Channel Driver Card
40461
-
Two channels of 8 to 10 MHz drivers (25 V amplitude). The output voltage range is ±25V, with independent high and low voltage settings. The inputs to the Card are optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel as low as one nanosecond increments.
-
Product
Modular Cards
SET 14XX
-
The carrier boards from the SET Modular Card 1415 / 1416 / 1417 series offer slots for 8 functional/measuring modules from the SET “SMARTbrick” series.
-
Product
32-Ch Isolated Digital I/O And 1-Ch Counter PCI Card
PCI-1750
Digital I/O
16 isolated DI and 16 isolated DO channels.High voltage isolation on all isolated channels (2,500 VDC).High sink current on isolated output channels (200 mA/channel).Supports dry contact or 5 ~ 50 VDC isolated inputs.Interrupt handling capability.Timer/counter interrupt capability.
-
Product
3U CompactPCI Serial 4-Port USB 3.2/2-Port Ethernet Card
cPCI-A3USB
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 4x USB3.2 Gen 1 ports and 2x RJ45 2.5G LAN ports in front panel- 1x USB2.0 port on board- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
Carrier Card
PEX442
-
The PEX442 Mezzanine Carrier Card allows designers the flexibility to extend and expand the IO capability of their systems by supporting high bandwidth links to combinations of XMC, PMC and AFIX (Additional Flexible Interface Xtensions) modules using PCI Express infrastructure.
-
Product
12 Port PCI Express
PEX 8615
-
The ExpressLane™ PEX 8615 offers 12 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 12 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8615 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
Product
Cable Testing and Diagnostics
-
Testing devices are required for successful commissioning of underground cable networks or repairs. Diagnostic testing devices are used for evaluating the cable status, which enables optimised and anticipatory maintenance planning and thus minimises failures. This planning is best established with the BAUR diagnostics system.
-
Product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
-
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
Product
32 Channel Optically Isolated Digital Card
104-IDIO-16
-
The Model 104-IDIO-16 is a 32-channel PC/104 utility board featuring 16 optically isolated inputs and 16 optically isolated solid state outputs. The isolated, non polarized inputs may be driven by either DC sources of 3-31V (or higher by special order) or AC sources at frequencies of 40Hz to 10KHz
-
Product
Full-Size PCI Express Mini Module With 32 Bit DIO
AX92904
-
*32 bit programmable DIO*Supports four 8-bit TTL level DIO ports with +5V powered*Each bit can be programmable as input or output*51 x 30 mm
-
Product
CPCI 48 Input I/O Card with Zilog Z8536 I/O Controller
CPCI-48IN
Controller
The input board consists of three Zilog Z8536 controllers for DC input control. An FPGA provides the timing and control. Each input has its own optical isolation, and supports a hardware adjustable resistor/opto-diode combination for various input voltage ranges. An AMCC PCI controller provides the interface to the host computer. All I/O is accessible from the front panel.
-
Product
Optocoupler and Relay Cards
-
For easy connection and galvanic isolation of digital input or output signals, we offer various optocoupler and relay boards.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 1.51MΩ
50-298-144
Programmable Resistor Module
The 50-298-144 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Frame Grabber/ Video Capture Cards
-
- Full product line support, including analog, GigE Vision, IEEE 1394b, Camera Link, HDMI, and 3G-SDI- Compatible with most popular cameras and software- Carefully selected embedded components ensure long term availability- Highly integrated with ADLINK I/O cards and embedded computing platforms
-
Product
48-lane, 48-port, PCI Express
PEX89048
-
The new PCIe Gen 5.0 (32 GT/s) PEX89000 series builds on the longevity of the Broadcom series of switches, now spanning 13 families. The PEX89000 family allows customers to build systems from simple PCIe connectivity inside the box to high-performance, low-latency, scalable, cost-effective PCIe fabrics for composable hyper-scale compute systems supporting ML/AI and Server/Storage applications.
-
Product
Dual Channel Driver Card
42460
-
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
Product
Dual Channel, Low-Noise DC Bias Card
PI-41701
-
The PI-41701 is a dual channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V and features programmable current limits with LED indicators and software interrupt to show/alert the user if the channel is in current limit. This card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output.
