-
Product
Cable Identification System & Cable Phasing System
Impulse Phaser
-
With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.
-
Product
Network, Port ID And Cable Tester
One for All PH-400
-
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
Product
Energized Cable Identification System
LCI™
-
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
Product
Cable Fault Locators
-
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Product
Cable Identification System
-
After excavation, sometimes it is confusing to identify the right cable from a bunch of cables. Cable Identification is very important for the safety of field personnel – Cutting a wrong cable can be fatal. So, we require a Cable Identification System to identify the wanted cable.
-
Product
Cable Identification System
KSG 200 / KSG 200 T
-
Cable identification withBAUR KSG 200. The KSG 200 cable identification system is used to identify single- and multi-core cables in a cable bundle or cable loom. By using the KSG 200, the risk of accidentally cutting a live phase is significantly reduced.* Cable identification on all types of de-energised cables* Reliable verification of the cable identification by means of the highly precise three-factor-analysis ATP* Safe cable identification on live low-voltage cables* Connection technology according to CAT IV/600 V
-
Product
Multi-function Cable Tester
NCT-100-S
-
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
Product
Cable Identifier
-
K&S Engineering and Scientific Ltd
K&S Engineering and Scientific LTD's Cable Identifier Set offers the user a compact, portable solution for cable identification. Depending on the user preference, the Cable Function Generator and Cable Identifier Unit can be jointly housed in a rugged briefcase, or alternatively, for the user requiring a more rugged unit, can be delivered as two individual units each with their own carry-case. With the Cable Identifier Set, power optimum levels are selected by means of a rotary switch and the power levels are displayed on a meter located on the Cable Function Generator. As the Cable Identifier Unit is capable of detecting magnetic fields around mains cables it has the added advantage of the user being able to use this as a stand-alone unit to detect power cable configuration.
-
Product
LAN Cable Multifunction Tester
TCT-2690PRO
-
LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.
-
Product
Coaxial Cable Tester
6106
-
Peaceful Thriving Enterprise Co Ltd
This device is designed to test the connection of F type coaxial cable. The testing includes continuity and cable mapping. The tester includes 4 mapping terminals with different color and a F type adapter, which are very helpful for cable identification.
-
Product
Cable Identification & Phasing
VCi-3™
-
The VCi-3™ system is designed for cable and phase identification, mainly for installation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct contact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends, 1m, Screwlocks
A068SFR-T-6B100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Cable Assy 9-Pin D-Type, M/M, 2m, HV
40-970-009-2m-MM-HV
Cable Assembly
9-Pin D-Type Male to Male Cable Assy, High Voltage, 2m Long
-
Product
10-meter (33 feet) Sensor Cable
E1739B
Calibration Cable
The E1739B 10-meter (33 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.Other cable lengths available: E1739A 5-meter (16 feet), E1739C (49 feet) 15-meter and E1739D 25-meter (82 feet).
-
Product
Cable Assy 9-Pin D-Type, F/F, 0.5m
40-970-009-0.5m-FF
Cable Assembly
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
-
Product
SCSI-100 To 2*SCSI-50 Shielded Cable, 1m
PCL-10251-1E
SCSI Cable
SCSI-100 to 2*SCSI-50 Shielded Cable, 1m
-
Product
Cable Assembly, Receiver, TriPaddle, 36" (2) 16-Pin Connectors
540029010201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36" (2) 16-Pin Connectors.
-
Product
Cable Assembly, ITA, I1 Hybrid 4/4, TriPaddle, High Power, 36", Flying Leads
410128565
Cable Assembly
Cable Assembly, ITA, i1 Hybrid 4/4, TriPaddle, High Power, 36", Flying Leads
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Unterminated (Tinned Ends), 0.5m
40-972B-200-0.5m-MU
Cable Assembly
This male rear exit to unterminated 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, unterminated with tinned ends. The connector assembly can be secured to the product by screwlocks.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends
A050DF5-C-0A100
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Mini DisplayPort Male to DisplayPort Male Display Cable
157232-02
DisplayPort Cable
Mini DisplayPort to DisplayPort Cable, 2m (-40 to 85 degree Celsius)
-
Product
Cable Assembly, Receiver, 20", Mini Power/TriPaddle, 9 Pin DIN, 4 Banana Plugs
540039030111
Cable Assembly
Cable Assembly, Receiver, 20", Mini Power/TriPaddle, 9 Pin DIN, 4 Banana Plugs.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 2m, Screwlocks
A068SMR-C-6B200
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Female, 2m
40-970-160-2m-FF
Cable Assembly
The cable assembly is suited for direct connection to Pickering Interfaces products using a Female DIN41612 connector. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
96-pin DIN Male to 96-pin DIN Female, 60 VC Shielded Analog Cable
157350-05
Analog Cable
SH-96-96-2, Cable for PXIE-4302, PXIE-4303, and PXIE-4339 to Rackmount Terminal Blocks, 5 Meters
-
Product
Cable Assembly, 50-Pin D-Type, Female To Unterminated With Ferrules, 0.5m HV, Exit Away From Pin 1
40-972-050-0.5m-FU-HV
Cable Assembly
50-Pin Female to Unterminated D-Type Cable Assembly, High Voltage, With Ferrules, 0.5m Long, 45º Cable Exit Away From Pin 1.
-
Product
3-m, 50-pin Dsub Cable
Y1136A
Multifunction Cable
Connect this m/f twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
Product
20-Pin GMCT Cable, Male To Unterminated, Ferrules, 16A, 2m
40-972C-020-2m-MU
Cable Assembly
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Ferrules, 0.5m
40-972-037-0.5m-FU
Cable Assembly
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
