-
product
PCI/PCIe Bus Extenders
Enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system. Enabling rapid production testing and engineering debug, the hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCI-e bus extender in the industry.
-
product
Contact Time Extender
CTX
The CTX relays supply a 1.5 to 2.5 seconds of a contact output time extension for a momentary contact input. The CTX allows slower device such as scada systems and annunciators to operate thus preventing data loss on the action of protective relays/devices or trip indicators such as the E-Max Trip indication Relay (TIR).
-
product
PCI To CPCI Or PXI Extender Board
MS 1720
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
product
Scanners & Extenders
Measurements International Ltd.
Sealed Relays with 4 A Carrying Capacity, 4-Conductor Wire or Binding Post Inputs, Optional 30 A Capacity, Low-thermal Matrix Design, Insulation Resistance > 1012 Ω.
-
product
Extender
3690-16
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
VME Extender
VMEE-M
VECTOR Electronics and Technology, Inc.
VMEEJ1 Extender on top and VMEEJ2 Extender on Bottom
-
product
Range Extender
By placing the remote control antennas in a better location, closer to the drone, it is possible to extend the range of the drone.
-
product
Extender
3690-15
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards.
-
product
Signal Generator Frequency Extenders
FES
These frequency extension modules easily connect to the output of your signal generator so you have high-performance source for your DUT characterization activities. Characterize your DUT with the confidence that the superior performance in terms of output power, spurious and harmonic will provide product accurate results.
-
product
6U VPX Extender Gen2
The VPX extender module is built to extend a 6U VPX module completely out of a chassis, providing access to all sides of the module for testing and debugging.
-
product
Extender
3690-17
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
PCI Express Cable Extender
SKU-016-XX
The PCI Express Cable Extender was designed to support the development and debugging of PCI Express boards. The PCI Express Cable Extender allows easy access from both sides of the PCI Express board that are plugged into the Extender. It has overcurrent protection and provides access to the PCI Express bus JTAG signals. By enabling access to the PCI Express bus JTAG signals, the PCI Express Cable Extender becomes a universal device that helps support the programming/loading of FPGA/CPLD during debugging and the verification PCI Express boards.
-
product
Extended Test Lead Kit
U1161A
The Keysight U1161A extended test lead kits are compatible with the U1230, U1240, U1250, and U1270 Series handheld digital multimeters. The set includes two extension test leads (one red and one black), two test probes, medium-sized alligator clips, and 4 mm banana plugs.
-
product
Test Adapter / Extender
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
product
VME Extender
VME64-M
VECTOR Electronics and Technology, Inc.
Excellent performance with a multi layer design
-
product
PCI Digitizers
ATS330
ATS330 provides the best value in the mid-range PCI Digitizer market. With its high performance, low noise 50 MS/s ADCs, fully programmable analog front-end and numerous other features, it is an ideal digitizer for many applications
-
product
CPCI Test Extender 6Ux180mm
117FFE6018-0XXX
The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.
-
product
Extended Version CODE300-32
Code300-32 Extended allows the running of two sessions of the program at the same time. This means that with two audio cards the system can handle up to 4 audio channels simultaneously: One could have two receivers, one into the Right (R) channel and the other into the Left (L) channel of the LINE IN input socket of the first audio card and the same configuration for the second audio card.
-
product
VME Test Extender 6U/220mm J1/J2
111EXT6122-012X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
PCI Express
PCI Express (PCIe) is a highly successful SerDes interface that is used in computing devices spanning a wide range of applications. Currently in its fourth generation with on-going roadmap development for a fifth generation, the PCIe interface is undergoing major technical advancements that require state-of-the-art development and validation tools. For example, Gen4 PCIe devices operate at 16 Gbps per lane and are expected to deliver very low bit error rate (BER) levels even over constrained and lossy transmission channels (e.g. printed circuit boards).
-
product
PCI Board
FastX1703-DIG
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
product
Extender
3690-3
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Serial Bus Buffers, Extenders, and Accelerators
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
product
Frequency Extender
DC100
The DC100 system can be installed in the HP8568B(see H96 option below) without compromising the performance of the original instrument. The spectral purity and power accuracy of the primary band ( 100hz to 1.5Ghz) are insured from corruption by careful design of the DC100 system. Additional protection of the primary band is guaranteed as the DC100 system is automatically switched off (all power removed) when in primary band operation.
-
product
Analyzer Calibration Extender
ACE
The ACE-1000A is a calibration solution that allows customers to self-calibrate their Kaelus PIM analyzers in the field. With successful calibration, ACE will extend your analyzer’s calibration while reducing downtime to less than one hour and increasing productivity by retaining instruments in the field.The Kaelus software guides the user through the calibration process from testing through payment including extending the calibration date of each Kaelus PIM Analyzer to 12 months, and printing the Certificate of Calibration certificate (CoC)
-
product
Extenders & Line Drivers
Extenders and Line Drivers enable reliable, long distance signal transmission over coaxial, twisted pair, or fiber optic cabling.
-
product
CMX RF Port Extender
CMX-Z25
Complex devices under test (DUT) come with additional antenna ports to support low, mid and high bands - and advanced MIMO schemes such as 4x4 MIMO. The R&S®CMX-Z25 is the solution: Up to 16 DUT ports can be supported with just 4 ports from R&S®CMX500. So even prototypes of 5G smartphones, tablets, laptops or industrial modules with an extended number of antenna ports can now be connected to a single R&S®CMX500. Together with the scalable CMX architecture any 5G and 5G Advanced mobile device can now be tested in one go - without recabling or 3GPP band combo limitations.
-
product
LXI WTB Extender
60-984-001
The 60-894 provides a simple an effective method of joining two LXI WTB bus cables together to extend the length of available cables. It is an ideal solution for cable extension where users need to experiment with different cabling solutions without having to totally replace the cables in the system. The 60-894 provides mating connectors for the WTB on each end connected together by a set of accurate differential transmission lines to avoid additional reflections on the cable. The 60-894 is entirely passive and is compatible with the LXI specification.
-
product
Optical Extended CAN Bus Jumper
EOFL-C
Optical Extended CAN Bus Jumper, using fault tolerant to optical conversion to extend the range, can extend up to 5 kilometers subsea.Qualified repeater housing protected on each side by highly reliable glass to metal sealed penetrators.
