Ultrasonic Sensors
See Also: Ultrasonic Transducers
-
Product
Single Axis AC Magnetic Field Sensor
MGCH-2
-
Macintyre Electronic Design Associa
The MGCH-2 is the lowest noise, highest sensitivity single axis AC magnetic field sensor available for the measurement of sub radio frequency fields. Because of its innovative design, the MGCH-2 amplitude response is insensitive to the frequency of the field over its 10 Hz to 100 kHz frequency band. Accuracy at 10 kHz is 0.1 dB, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Fiber Optic Sensors And Amplifiers
-
Omron’s high-performance fiber optic sensors and amplifiers come in a wide variety of configurations to meet your specialized requirements.
-
Product
pH Logger Sensor
NUL-206
-
This sensor can be used to measure the static pH values of common liquids (water, milk, soft drinks, vinegar, etc.) as well as the changing values in titrations or experiments such as those looking at the effect of antacids.
-
Product
Inductive Sensors
-
Inductive sensor designed to detect shaft speed, shaft position, gate position, or object presenceTotally sealed constructionMulti-voltage 24 - 240 VAC/VDCDetects ferrous targets up to 5/16" (8 mm)IP 65 Protection
-
Product
USB Sensor Hub
E1736A
USB HUB
Small and light weight, the Keysight E1736A USB Sensor Hub gives users the ability to connect up to four sensors to a PC. Connection from the sensors to the sensor hub is made using interchangeable cables available in 5m, 10m, 15m, and 25m lengths. Connection is made via an easy to snap in connection.
-
Product
Liquid Level Sensors
-
Are used to detect liquid levels or interfaces between liquids such as oil and water or liquids and solids. They can be defined as sensors or transducers, or as integrated systems with instrumentation and control capabilities.
-
Product
Family of Wavefront Sensors
ShaH
-
The family of fast, accurate and reliable wavefront sensors. High quality lenslet arrays optimized for reducing the subapereture crosstalk. An interface to a variety of CCD and CMOS sensors allows a wide range of acquisition bands from UV to near IR.
-
Product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
-
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
IR FPA sensors
-
IR FPA sensors are the most important modules of thermal imagers. Design of sensor electronics (camera core) is a crucial part of designing of new thermal imager. Knowledge of precise parameters of IR FPA sensor is needed by both professionals involved in both IR FPA technology/thermal imagers technology because parameters of IR FPA sensors determine performance limits of thermal imagers. Therefore test equipment that enable measurement of IR FPA sensors is a vital tool for development of both IR FPA technology/thermal imagers technology. It is commonly known that data sheets provided by manufacturers of IR FPA sensors (both cooled or non-cooled) provide too little details for electronics designers. Sometimes the provided data is not accurate enough and better sensor performance can be achieved using modified control signals. Therefore design teams loose sometimes years to develop electronic camera core optimized for a specific IR FPA sensor. When the type of the IR FPA sensor is changed the whole process is to be repeated. In this situation an universal, flexible camera core that would accept IR FPA sensors from different manufacturers and to carry out semi-automatic determination of optimal signal controls for a specific IR FPA sensor would be highly desirable.
-
Product
Ultrasonic Thickness Gauge
-
High-precision ultrasonic thickness gauge, suitable for various materials high-precision measurement needs, can be applied to steel, cast iron, aluminum, copper, zinc, etc.
-
Product
Concrete Humidity Sensor
BlueRock
-
BlueRock is a rugged, waterproof sensor designed to wirelessly monitor the relative humidity and temperature of concrete from fresh to hardened stages.
-
Product
Force Sensor Elements
-
TE Connectivity (TE) enables OEMs to measure force using MEMS-based technology load cells. The same proprietary piezoresistive silicon strain gage technology used to measure pressure can also be configured into a reliable, low-cost package to measure force.
-
Product
Inductive Proximity Sensors (Square)
SP2
-
Easy installation, high-speed pulse generator, high-speed rotation control, and more. A wealth of models ideal for limit control, counting control, and other applications. Sensing distance from 1~2/2 ~ 6/ 5~ 12/10~15mm. Housing by PBT with strong structure and acid resisting available.
-
Product
Cylindrical Inductive Proximity Sensor
-
Shanghai Pubang Sensor Co.,Ltd.
1.Non-contact position detecting,non-wear,high-reliability2.Clear visible indictor design,easy to estimate the working state3.Various type of Sensor,diameter spec.from Φ4 to Φ34,housing length,from ultra-short,short to standard type4.Equipped cable and connector,easy to maintain5.Protection class IP67(IEC)
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
Fail Safe Mechanical Speed Sensor
95004
-
The Fail-Safe rotary speed control is a fluid/magnet actuated mechanical switch. It incorporates the consistent and dependable forces of gravitation and magnetism to achieve its mechanical switching action. Because the unit requires no electrical power to operate, it can be used in remote areas where access to power supply is inconvenient or unavailable.
-
Product
Split type AC Current Sensor
CTF-50A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of terminal feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
SparkFun Ambient Light Sensor Breakout
TEMT6000
-
Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don't. Sensor acts like a transistor - the greater the incoming light, the higher the analog voltage on the signal pin.
-
Product
Charge Logger Sensor
NUL-246
-
This sensor measures electrostatic charges. It can be seen as a highly sensitive electroscope indicating whether a charge is positive or negative. Other uses are: to explore the nature of static charge, to measure both charge and voltage, to measure charge by induction, quantify the charge on a capacitor or discover the charge distribution on a conducting sphere.
-
Product
Compact Flow Sensor For Gas Lapiflow (R)
FSM2
-
This is a small flow sensor for gas with a 2-color 2-screen display.We have a lineup of two types: integrated display type and separate display type.
-
Product
Universal LightProbe S2 Sensors
LED Sensor
Optomistic Products’ Universal LightProbe S2 Sensors are designed for the In-circuit, Functional or Finished Product test of an LED’s color and/or intensity. Implemented in a unique and customizable 2-Part solution, the S2 Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.
-
Product
Split type AC Current Sensor
CTF-200A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
-
Product
Scattering Sensors
-
Scattering sensor data offers links to particulate bigeochemistry and ocean color. Sea-Bird Scientific offers a wide variety of scattering sensor configurations and measurement capabilities. Our sensors are available in single, dual, and three-measurement combinations.
-
Product
Sensors
TA120
-
The TA120 sensor combines the precision of a Class 1 sound level meter, maximum protection of an outdoor kit and full connectivity with open source platforms.
-
Product
4-20mA Sensor Converter
ENVIROMUX-S420MA-24V
-
External RJ45 device monitors up to two 4-20 mA analog sensors. Supports ISA Type 2, ISA Type 3, and ISA Type 4 sensors. Provides 24VDC, 25mA for each sensor. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 500 ft. (152 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: RoHS.
-
Product
Optical Distributed Sensor Interrogator
ODiSI 6000 Series
-
The ODiSI 6000 Series is a powerful measurement system specifically designed to address the modern test challenges of advanced materials and systems. The ODiSI system delivers the highest definition distributed sensing of strain and temperature available, giving you maximum insight and visibility into your component or process.
-
Product
Uncooled Infrared Cameras and Sensors
-
Uncooled Infrared Cameras and Sensors by Lynred USA: XGA/SXGA Format, VGA Format, QVGA Format
-
Product
5VDC Sensor Converter, 12VDC, 25mA
ENVIROMUX-S5VDC
-
External RJ45 device monitors up to two linear DC sensors, 0VDC ~ 5VDC. Output for each sensor: 12VDC, 25mA. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,956,288 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
Mini Digital Output Pressure Sensor
DLHR Series
-
The DLHR Series Mini Digital Output Pressure Sensor is based on All Sensors' CoBeam2 TM Technology. This reduces package stress susceptibility, resulting in improved overall long term stability and vastly improves the position sensitivity. The digital interface option eases integration of the sensors into a wide range of process control and measurement systems, allowing direct connection to serial communications channels. 0.5 to 60 inH2O Pressure Ranges
-
Product
High Intensity Acoustic Sensors
-
Columbia Research Laboratories
Columbia's High Intensity Acoustic Sensors are designed for the measurement of gas-borne sound in industrial applications. They are constructed of type 316 SS for use in corrosive environments. These sensors offer a variety of connector and mounting options, all of them when combined with the all-welded construction provide a true hermetic seal.
