Ultrasound Sensors
-
Product
Roller Contact Sensors
-
Electronic Development Labs, Inc.
EDL’s roller contact sensors are expertly crafted to provide exceptional measurements on both moving flat and rotating cylindrical surfaces, along with stationary objects.
-
Product
Uncooled Infrared Cameras and Sensors
-
Uncooled Infrared Cameras and Sensors by Lynred USA: XGA/SXGA Format, VGA Format, QVGA Format
-
Product
Variable Reluctance Absolute Pressure Sensor
AP10
-
The AP10, Absolute Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full-scale output of 40 mV per volt at 3kHz. The unit operates with carrier systems including the Validyne CD15 sine wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator to produce a high level analog DC output suitable for recording and control.
-
Product
Silicon Irradiance Sensors
-
Measure the irradiance intensity on your photovoltaics system precisely at an affordable price with IMT Technology’s robust silicon solar irradiance sensors (Si sensors).
-
Product
Gas Flow Sensors
ESRF-HF Transmitter
-
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
Product
Vehicle Presence and Data Collection Sensor
FLIR TrafiCam x-stream2
-
The FLIR TrafiCam x-stream2 combines a digital camera and video detector into a single vehicle presence sensor. Detecting moving and stationary vehicles at signalized intersections, TrafiCam x-stream2 transmits vehicle presence information to a traffic controller via detection outputs or TCP/IP communication for adaptive and responsive signal timing. Each cost-effective TrafiCam x-stream2 sensor helps reduce vehicle idling time and optimize traffic flow.
-
Product
Structural Monitoring Sensors
-
Crouzet also offers services (instrumentation) for the measurement, control and monitoring of your industrial processes, equipment and structures. With our extensive experience and design office, Crouzet can bring you specific solutions that comply with your specifications, while respecting both your technical and financial constraints.
-
Product
Signal Conversion Box for Linear Gauge Sensor
DG-0010/0020
-
This is a signal conversion box to convert 2-phase signals (TTL) from the linear gauge sensor GS/BS series into open - collector (DG-0010) or line driver (DG-0020) .This conversion box allows direct connection with the PLC *. It can also be transmitted over long distances.
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
Sensor for Filament Inspection
EyeFI
-
EVT presents the EyeFI - the sensor for the inspection of filaments. The sensor contains two cameras with an Aptina sensor and S-Mount lenses. The cameras are perpendicular to each other. It is therefore possible to inspect two sides of the filament, which means that the EyeFI can detect if the filament is out-of-roundness. Additionally the errors and defects can be detected. For example the occurring flaws are point-shaped or partly flaked, or point-shaped and transverse, or also looking like a longitudial rib, or only spots in different shapes. The defects can be detected with the EyeFI sensor. The EyeFI contains board cameras with sensors from Aptina, the IoCap and an evaluation processor. The housing is about 14x10x4 cm in size. The IoCap is the image-capture-IO-board, which is designed and developped by EVT.
-
Product
Radar Level Sensor
VRS-20
-
Versatile and simple to install, the VRS-20 has been developed by Valeport to work seamlessly with the TideMaster Tide Display/Logger and other third party data loggers using RS232, RS485 and SDI-12 communication. Non-contact technology removes the installation, corrosion & fouling issues of submerged sensors, while simplifying datum control. Accuracy and performance are unaffected by changes in water density and atmospheric conditions.
-
Product
RF Power Sensor Solutions
-
Bird provides innovative power sensor solutions for all types of RF applications. From simple directional power sensors for the measurement of transmitter output power and VSWR measurement and monitoring applications, to highly accurate self correcting power sensors for process control applications, you can rely on Bird sensor products to meet the needs of your unique applications.
-
Product
InGaAs Optical Power Head
81624C
Optical Power Sensor
The new 81624C optical power head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81624C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
Robust Photoelectric Sensor
RX
-
Panasonic Industrial Devices Sales Company of America
Sturdy Photoelectric Sensor made of die-cast zinc alloy.
-
Product
High Temperature Magnetic Speed Sensors
-
SPECTEC Innovative Sensor Solutions
High temperature speed sensors (up to 454° C) are sensitive, shock resistant & reliable for high temp applications in harsh environments, such as race car engines and transmissions. SPECTEC's high temperature magnetic speed pickups are used as transmission sensors, engine governors, output shaft sensors and flow meter sensors. SPECTEC's high temperature magnetic pick-ups are standard in 5/8-18, 11/16-24 and 3/4-20, and M18 shell sizes.
-
Product
Multiparameter CTD with a Wide Choice of Standard Sensors.
MIDAS CTD+
-
Featuring Valeport’s latest 400 Series electronics, the CTD+ will sample all fitted sensors at exactly the same instant, at up to 8Hz. Advanced setup software allows a variety of sampling regimes including burst modes, delay starts and conditional sampling. Available with up to 64Mbyte memory and internal battery pack, as well as a selection of real-time output formats, the CTD+ may be used with Valeport’s own water bottle carousel.
-
Product
Sensors And Components
-
ION Science is a leading manufacturer of VOC gas sensors, with PID sensor technology trusted by major gas detection manufacturers globally for accurate detection of volatile organic compounds (VOCs). To the ever-growing sensing portfolio, ION Science offers Development Boards and Kits specially designed to offer OEMs at a simple, low-cost with means of integrating MiniPID sensors into existing systems and applications. Due to tightening legislation and the growing global focus on air quality, worker safety and environmental emissions are driving the requirements for a new generation of measurement and monitoring systems. The multi-award-winning Disc Pumps are now available and distributed by ION Science.
-
Product
Soil Moisture Sensor
SoilWatch10
-
SoilWatch 10 is a soil moisture sensor which allows measuring relative water content in the soil. Our sensor does not have any exposed electrodes that usually corrode in resistive sensors. Whats more the reads will almost not drift over time or with temperature changes. Our sensor will give the same readings regardless of supply voltage. The sensor is weatherproof. It can be buried in soil for extended periods of time without adverse effects on accuracy or reliability. Designed to work with Arduino.
-
Product
CGS500-IR NDIR Gas Sensor
-
The CGS500-IR sensor is a NDIR (non-dispersive infrared) sensor designed to replace thermocatalytic gas sensors for monitoring hydrocarbon gases in the range 0-100% LEL. The CGS500-IR is available as a sensor only or fitted in an EEx e certified junction box.
-
Product
General Purpose Vibration Sensors
AC104
-
Multi-Purpose Accelerometer, Side Exit Connector / Cable, 100 mV/g.
-
Product
CO₂ Humidity And Temperature Sensor
SCD40 (Qwiic)
-
The SCD40 from Sensirion is a high quality Photoacoustic based CO₂ sensor capable of detecting 0 to 40000ppm with the best accuracy over 400-2000ppm ±(40ppm+5%). In order to improve accuracy the SCD40 has integrated temperature and humidity sensing built-in. For additional accuracy the SCD40 also accepts ambient pressure readings!
-
Product
E-Type Thermocouple, 32°F to 900°F Temperature Sensor
745690-E001
Thermocouple Contact (ITA)
E-Type Thermocouple, 32°F to 900°F Temperature Sensor - The E-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the E-Type Thermocouple and acquire synchronized temperature data in units of degrees. The E-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Water Alarm with Remote Sensor
00800
-
Protect your home or business from costly water damage by placing a Sonin Water Alarm with Remote Sensor anywhere there is a potential for a leak.
-
Product
Temperature Measurement IR Sensors & Detectors
M34
-
A thin-film thermopile in a TO-5 package with an active area of 3.16mm x 0.4mm that offers low noise output.
-
Product
PV Module Temperature Sensores
-
Measure the temperature of your PV module with utmost precision and minimal drift to assess your system’s productivity.
-
Product
One-Piece Optical Sensor Head
OP
-
Sciences et Techniques Industrielles de la Lumière
OP series consists of a one-piece optical sensor head for dedicated applications (e.g. long distance).The performance and specifications are dedicated to various applications in the industry.Typically integrated as OEM for measuring 3D shapes, glass thickness, autofocus, OP series fits a wide range of applications.
-
Product
Car Oxygen Sensor
KS60044
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
High Speed, Multi-Point Laser Displacement Sensor
HL-D3
-
Panasonic Industrial Devices Sales Company of America
The HL-D3 Series was developed based on a new concept of capturing the shape of objects with points instead of a line. The new Panasonic Displacement Sensors feature faster measurement, achieved by selecting only the desired sensing points; and adjustable light intensity for each sensing point, which contributes to stable, precision detection; both without compromising the Z-axis resolution. This is equivalent to the performance of 500 high-precision Displacement Sensors with a resolution of 1 μm 0.039 mil.
-
Product
Dynamic High Pressure Sensors
-
Columbia Research Laboratories
Columbia's line of Dynamic Pressure Sensors can also serve as Acoustic Sensors (Microphones). They are designed to measure fast pressure variations, surges and dynamic blasts. The Sensors vary from low cost, small size, and lightweight to High Pressure (to 10,000psi) units, with all-welded contructions for extreme ruggedness, making them excellent choices for a wide range of applications.
-
Product
SparkFun Atmospheric Sensor Breakout
BME280 (Qwiic)
-
The SparkFun BME280 Atmospheric Sensor Breakout is an easy way to measure barometric pressure, humidity, and temperature readings, all without taking up too much space. Basically, you can find out anything you need to know about atmospheric conditions from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
