10/100/1000BaseT
IEEE 802.3ab standard for Gigabit Ethernet over copper wiring.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
Fault Insertion Unit
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
789546-01
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
Network Interface Card
PMC-GBIT-DT2BP
Interface Card
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
Product
Miniature Airborne Communications Converter
MACC II - Converter
-
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
Product
AFDX ® / ARINC 664 Test Cards
-
Our AFDX ® / ARINC664 test cards can be used for test and simulation applications in which it is necessary to send and receive data via the AFDX® data bus. They support the 10/100 Mbit / s ARINC 664 Part 7 Ethernet interface as well as the next generation 1 Gbit / s Ethernet. / ARINC 664 test cards are delivered with device drivers, high-level interfaces (APIs) for Windows Linux, VXWorks and LabVIEW / LabVIEW Real-Time (further on request).
-
Product
100base-T1 Ethernet (BroadR-Reach®) Logging Expansion With Low Latency
PT-15B
-
The PT-15B expands the PM-200 data logger from the Power Family by adding twelve 100base-T1 interfaces. Ethernet traffic is looped through the device with constantly low latency irrespective of the frame length. This means that the time synchronization protocols of the logged Ethernet interfaces are not affected. 100base-T1 packets are time stamped, filtered and sent to the PM-200 data logger via a 1000base-T interface.
-
Product
EOC Master
EOM-7224
-
Hangzhou Softel Optic Co., Ltd.
*EOCM-7224 is the integrate EOC Master with two EOC master module and one ONU module.*EOCM-7224 EOC Master can provide high speed data service based on coaxial cable network. EOCM-7224 built in a ONU. *The module supports IEEE 802.3ah standards. It provide one SC/PC optical EPON uplink port and two 10/100/1000Mauto-negotiable Ethernet RJ45 ports. By using the EPON technology, the ONU Module can provide a high-speed data channel through a single optical fiber with a rate of 1.25 Gbit/s on bi-direction. In addition, it offers the QOS, flexible bandwidth allocated to provide quality high-speed data service, voice service, and video service.
-
Product
Airborne Network Flight Test Recorder
TTC nREC-7000
-
Curtiss-Wright Defense Solutions
The nREC-7000 is a high speed network recorder for use with Flight Test Data Acquisition and Multiplexing units. The nREC-7000 accepts data for recording on two 10GBASE-SR ports and two 1000BASE-T ports that can store data at sustained speeds of up to 1,000 MBps per 10GbE port. The recorder is also capable of acquiring, formatting (using PCAP, DARv3 or IRIG-106 Chapter 10/11), and recording 10GBASE-SR Ethernet at line rate.
-
Product
4G Powerful Routers - ICR-3200 & SmartFlex
-
Powerful LTE routers with Ethernet 10/100, RS232/485, and WIFI operating on high-performance CPU and memory ready to host IoT applications.
-
Product
PhyView Analyzer
PVA-3000
-
Connects up to 24 10/100/1000Base-T ports and provides access to the PHY Performance Test Suite supporting one-click, fully automated transmitter, receiver, and, auto-neg testing.
-
Product
8FE Slim-Type Unmanaged Industrial Ethernet Switch
BB-ESW108-A
Ethernet Switch Module
8 x fast Ethernet ports with auto MDI/MDI-X, Supports 10/100 Mbps auto negotiation, Compact size with DIN rail and wall mount. Supports redundant 12~48 VDC or 10~24 VAC power input, Wide operating temperature range of -40 ~ 75°C, C1D2 for hazardous locations.
-
Product
4G & 5G Routers: Essential Ports - ICR-2000/2400
-
4G cellular routers operating on LTE Cat. 4 cellular technology equipped with basic interfaces with up to two Ethernet 10/100 ports.
-
Product
2 Port 10/100/1000Mbit/s AFDX/ARINC664P7 Test, Simulator And Monitor Module For PMC
AMCX-FDX-2/B
Monitoring Module
AFDX®/ARINC664P7 Test and Simulation module for PMC with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
Product
8FE Slim-Type Unmanaged Industrial Ethernet Switch
EKI-2528I-LA
-
8FE Slim-type Unmanaged Industrial Ethernet Switch with Low VAC Power Input, -40~75℃, 8 x fast Ethernet ports with auto MDI/MDI-X, Supports 10/100 Mbps auto negotiation. Compact size with DIN rail and wall mount, Supports redundant 12 ~ 48 VDC or 10 ~ 24 VAC power input.
-
Product
Metro Expert
MX Series
-
The VeEX® MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/ Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
Product
1-Port Modbus Gateway
EKI-1211
-
1 x 10/100 Mbps Ethernet port Integrates Modbus TCP and Modbus RTU/ASCII networks. Baud rate: supports up to 230.4 Kbps. Supports up to 16 connections per serial port under Modbus client mode and 32 sessions under Modbus server mode.
-
Product
4FE+1FE SC Multi-Mode Unmanaged Ethernet Switch
EKI-2525M
-
Provides 4 x 10/100 Mbps Ethernet ports with RJ45 connectorProvides 1 x 100 Mbps Multi-mode SC type fiber optic portSupports full/half duplex flow controlSupports MDI/MDI-X auto crossoverProvides redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mount
-
Product
Fanless Embedded System With LGA1150 Socket Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q87, 2 HDMI/VGA/DisplayPort, 4 GbE LANs, 6 USB 3.0, Wide Range DC-in And PCIe Mini Card
eBOX670-883-FL
-
The eBOX670-883-FL supports the LGA1150 socket type for 4th generation Intel® Core™ i7/i5/i3 and Celeron® processors (formally codename: Haswell) with Intel® Q87 Express chipset. Under this rich support system, the eBOX670-883-FL allows wide operating temperature ranging from -40°C to +55°C for the most endurable operation. The outstanding embedded controller comes with four 10/100/1000 Ethernet ports, Jumbo Frame (9.5K), PXE Remote Boot, Teaming, and wake-on-LAN (WOL) function to highly enhance its network connection speed. Additionally, the eBOX670-883-FL supports up to three independent hi-resolution displays or a 4K display. Undoubtedly, this rugged fanless embedded computer is the best solution for any industrial field, including host computers, cloud computing servers, multimedia applications, and automation systems.
-
Product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
LXI Microwave Multiplexer, 50Ω Dual 18-Channel 6GHz SMA
60-891-019
Multiplexer Module
This LXI Microwave Multiplexer is controlled through an LXI interface based on 1000Base-T Ethernet. This provides a quick and easy method of installation. It also provides a simple way of controlling it at a remote location through its API or built in soft front panel.
-
Product
CPCI ARM LPC3250 Board
MS 1513
-
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
Product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
785831-33
Controller
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
Product
Dual Function Slot MOSA Data Concentrator Unit (DCU)
NIU2A-DCU-01
Data Concentrator Unit
NIU2A-DCU-01 is a Modular Open Systems Approach (MOSA) Data Concentrator Unit with low power high performance ARM Cortex -A9 processing. 512 MB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet and optional Fiber Optic Ethernet support
-
Product
8GE Unmanaged Ethernet Switch, -40~75℃
EKI-2728NI
-
Provides 8 Gigabit Ethernet ports with Auto MDI/MDI-X, Supports 10/100/1000Mbps Auto Negotiation, Supports jumbo frame transmission up to 9kbytes. Provides Slim size, DIN-rail with IP30 metal mechanism, Supports Redundant 12 ~ 48 VDC power input and P-Fail Relay, Supports a wide temperature range: -40 ~ 75° C.
-
Product
Ethernet Switch and Router
VPX6-684
-
Curtiss-Wright Defense Solutions
Curtiss-Wright's VPX6-684 FireBlade provides Systems Integrators with a fast, secure and unified approach to interconnect subsystems, chassis, cards, and compute nodes within any given platform using 1 or 10 Gigabit Ethernet links. Providing up to 24 wirespeed 10/100/1000 Mbps interfaces and up to four 10 Gbps interfaces in a single 6U VPX slot, the VPX6-684 Ethernet Switch is ideal for architecting system-wide Intra-Platform Networks (IPNs).
-
Product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
Interface Card
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
Product
TET Modules
-
The tET Series tiny Modbus TCP based I/O modules provide digital I/O functions, support I/O pairing and have a din rail mount. The module can be remotely controlled through a 10/100 M Ethernet network by using Modbus TCP/UDP protocol. They are configurable through a standard web browser and are easy to use. The tET Series can be used with our FREE EZ Data Logger Software.
-
Product
2-Port 10/100/1000 Base-T Ethernet NIC, Intel® 82580DB, PCIe I/F to processor
EM1
-
The EM1 module integrates the Intel® 82580 GbE Controller with supporting magnetics and circuitry to provide dual-port gigabit (10/100/1000Base-T) Ethernet network controller functions. NAI Single Board Computer (SBC) boards are typically designed with dual-port NICs. The EM1, with direct-connect PCIe interface, allows for seamless SBC/processor configuration providing access to additional Ethernet communication port functions.
-
Product
Fanless Embedded Box PCs
ARK Ultra Rugged Series
-
The Fanless Embedded Systems ARK-V&S series are designed for rugged and space-critical in-vehicle and video surveillance applications. These embedded systems feature in-vehicle power (9~36Vdc, ISO-7637-2), in-vehicle certifications (E-Mark, IEC-60721-3-5 5M3), extension capability and wireless communication (GPS/G-sensor/Wi-Fi/3G/CANBus) for in-vehicle NVR applications. As for video performance, these embedded systems provide high graphic power (Up to 1080p/720p @120fps) and support IP Camera (4 Ports 10/100 PoE, IEEE802.3af) to maintain stable performance for mobile NVR
