CMOS
Complementary Metal-Oxide-Semiconductor is a low power and heat integrated circuit.
See Also: Image Sensors
-
Product
Digital I/O Board
3512
Digital I/O
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
Machine Vision Camera - 1.6 MP, 78 FPS, Sony IMX273, Color
Blackfly S Board Level
-
The FLIR Blackfly Board Level variants are high performance, machine vision, area scan cameras designed for embedding into tight spaces. Unlike many board level cameras, it boasts a rich feature set applied to the latest CMOS sensors; the same feature set as the cased version. It is ready for integration with proven compatibility with popular SBCs and SOMs. The Blackfly S board level models enable OEMs to develop smaller, lighter, and lower cost solutions with embedded system connectivity and rich features.
-
Product
Scientific CMOS Large Field of View Camera
Iris 15
-
The Iris 15 Scientific CMOS (sCMOS) camera provides a large field of view and the highest resolution with its 15 Megapixel design.
-
Product
Low Light Imagers for Defense
-
Teledyne Imaging addresses low light imaging applications with a range of standard CMOS and EMCCD image sensors suitable for defense and security surveillance systems, whether for battlefield, vehicle, airborne, CCTV or security day camera’s.
-
Product
4K Autofocus MIPI NVIDIA® Jetson TX2 Camera Board
E-CAM132_TX2
-
e-CAM132_TX2 - 13MP Autofocus Jetson TX2 camera board is a 4-lane MIPI CSI-2 camera solution for NVIDIA® Jetson TX2 developer kit. This camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® and an integrated high-performance image signal processor (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control). e-CAM132_TX2 is a two board solution consists of a base board and a 13MP autofocus camera board. This camera board is connected to the base board using 30 cm micro-coaxial cable.
-
Product
Miniature 8-channel photon counter
id150 SERIES
-
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
Product
sCMOS Camera
Dhyana 400D
-
Fuzhou Tucsen Photonics Co.,Ltd
Dhyana 400D is equipped with a brand new 1.2 inch scientific CMOS sensor, which provide 80% quantum efficiency at 600nm. The 1.2 inch sensor size and 6.5X6.5um pixel size is more suitable for microscopy standard C-mount imaging. When comparing to other existing scientific CMOS camera products, Dhyana 400D has a hardware 2X2 binning function which make it superior sensitivity for low light imaging. When comparing to other existing scientific CMOS camera products, Dhyana 400D has a hardware 2X2 binning function which make it superior sensitivity for low light imaging.
-
Product
3.4 MP Custom Lens Low Light Camera Module
e-CAM30_CUMI0330_MOD
-
e-CAM30_CUMI0330_MOD is a high performance, small form factor, 3.4 MP pluggable Low Light Camera Module with S-Mount lens holder. It is based on AR0330 - a 3.4MP CMOS Image sensor from ON Semiconductor®. It has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs the entire Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images, videos and the optional MJPEG compressions.
-
Product
Temperature & Humidity Transmitter
HTO
-
- CO2 measuring element: NDIR Sensor 2- CO measuring element: Electrochemical sensor- Temperature/Humidity sensing element : CMOS sensor- Analog output option:4~20mA or 0~10V- Communication output option:RS485 Modbus RTU- Configured by PC with free software via USB cable (option)- Present value offset adjustable- Inside buttons for adjust output parameters- LCD backlight color to Indicated CO/CO concentration 2- Temperature measuring range can be -50~100℃ via USB console port to setting
-
Product
X-ray Camera
-
Up until the introduction of SID-A50, X-ray inspection systems has been using detectors such as Image Intensifier (I.I.) and C-MOS Flat Panel Detectors, which needs to convert X-ray into optical light first, in order to visualize X-ray.These Indirect Conversion Method X-ray Detectors comes with multitude of issues. These problems include but not limited to; Low Sensitivity, Fuzziness, Time Degradation, Inadequate Life
-
Product
1.3 Million Pixel CMOS Image Sensor
Sapphire 1.3M
-
This 1.3 million pixel Sapphire CMOS image sensor, designed on Teledyne e2v’s proprietary Eye-On-Si CMOS imaging technology, is ideal for diverse applications where superior performance is required. The innovative pixel design offers excellent performance in low-light conditions with both electronic rolling shutter and electronic global shutter, with a high-readout speed of 60 fps in full resolution. Novel industrial machine vision application features such as multi ROI and histogram output are embedded on-chip. Very low power consumption enables this device to be used in battery powered applications.
-
Product
USB 3.0 Cameras
See3CAM
-
See3CAM - a new series of USB 3.0 Camera. It's the world's first UVC compliant USB 3.0 Camera Module that is plug & play on Windows/Linux. USB 3.0 camera board does not require additional device drivers. These USB3 cameras work with standard Windows (DirectShow) and Linux (V4L2) software. USB3 Camera is based on Aptina & OmniVision CMOS sensors.
-
Product
Ethernet Cameras
HT Series
-
Our cameras are available with resolutions of 2, 4, 12, and 20 megapixels in monochrome, color, or near-infrared enhanced (NIR) with full frame rates of up to 338fps, 179fps, 84fps, and 32fps respectively (we can also provide taped on glass). As the first 10GigE industrial digital camera series in the world, our HT cameras obtain their high performance from industrial CMOS sensors with Global Shutter technology in combination with the cross-industry standard 10 Gigabit Ethernet (10GigE) interface.
-
Product
2D CMOS Image Sensors
Emerald 36M
-
Superior 36 Megapixel resolution - 6K square resolution - Multi-ROI feature enabling more objects to be captured in a single high resolution shot - Small global shutter pixel for blur-free images.With its high resolution, Emerald 36M improves inspection accuracy, increases throughput through an optimized inspection system path, and covers wider areas for surveillance or aerial mapping.
-
Product
Data Acquisition
-
For devices with analog outputs, we are now shipping our new multi-channel data acquisition system. This high-speed, low-noise solution is highly modular, so you can test scientific CCDs and high-speed machine-vision CMOS sensors with the same basic system. Swappable pre-amps and A/D converter modules enable you to reconfigure your test system to fit your needs.
-
Product
Cameras
TMX
-
The Phantom TMX series of cameras is the next evolution of ultrahigh-speed imaging. Designed with a revolutionary back side illuminated, custom CMOS sensor it delivers clear, high quality images at speeds not previously possible.
-
Product
Operational Amplifiers
-
Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.
-
Product
Isolation and Power Solutions
-
Silicon Labs' innovative digital isolation and power product portfolio includes CMOS digital isolators, isolated gate drivers, isolated current sensors, isolated system products and Power over Ethernet (PoE) families. These mixed-signal IC solutions leverage Silicon Labs' superior isolation and high voltage expertise to enhance power system performance, flexibility and reliability while reducing system size and cost. The entire isolation portfolio supports isolation voltages up to 5 kV.
-
Product
Single Sensor - Monochrome Line Scan Cameras with Fast Scan Rates
-
JAI’s monochrome line scan cameras provide an excellent combination of high resolution and fast scan rates.The Sweep SW-8000M-PMCL model features an 8192-pixel linear CMOS sensor delivering a line rate of 100,000 lines/s (100 kHz) over a Camera Link interface. The SW-4000M-PMCL model is based on a 4096-pixels sensor capable of running as fast as 200,000 lines/s (200 kHz) over Camera Link.
-
Product
Memory
-
Renesas offers MIL-STD-883-compliant CMOS random access memory (RAM) and CMOS programmable read-only memory (PROM) devices that are that are qualified to QML Class Q military standards.
-
Product
3.4 MP Autofocus Low Light USB Camera Board With Liquid Lens
See3CAM_30
-
See3CAM_30 is a 3.4MP UVC Compliant, low light, autofocus USB camera with liquid lens. It is a two-board solution with AR0330 CMOS image sensor from ON Semiconductor and USB 3.1 Gen1 type C interface board. See3CAM_30 is a colour camera with S-mount lens holder and does not require any special camera drivers to be installed in the host PC. See3CAM_30 is customizable and it is a Ready-to-Manufacture camera with all the necessary firmware built in and compatible with the USB Video Class (UVC). It consumes less power and doesn't heat up. There is no mechanical movement like in VCM motor for autofocus. Hence the life of the lens increases.
-
Product
TMR Switch Sensors
-
MultiDimension Technology Co.,Ltd.
A digital unipolar magnetic switch that integrates TMR and CMOS technology in order to provide a magnetically triggered digital switch with high sensitivity, high speed, and ultra-low power consumption. It is designed for use in applications that are both power-critical and performance-demanding. It contains a push-pull half-bridge TMR magnetic sensor and CMOS signal processing circuitry within the same package, including an on-chip TMR voltage generator for precise magnetic sensing.
-
Product
Ethernet PHY
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
Product
FastCamera
FC1700
-
The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.
-
Product
8 Mega Pixel Auto Focus MIPI Camera Module
e-CAM80_MI8865_MOD
-
e-CAM80_MI8865_MOD is a 8 MP Autofocus MIPI RAW camera module based on Ominivision's OV8865 CMOS image sensor. The 1/3.2-inch OV8865 is a low-power high-performance color CMOS Image Sensor featuring an improved 1.4-micron with BSI technology. OV8865 is already a proven sensor in the market with dynamic range and reduced dark current that enables superior high and low light image capture. Note: You would require an external ISP to process the data. Contact us to purchase the ISP.
-
Product
Front Side Illuminated Sensor with Pixel Size of 5.3µm with NIR Spectrum Sensitivity
Ruby Family
-
The EV76C660 and EV76C661 are members of Teledyne e2v’s Ruby family of CMOS imaging sensors. These breakthrough devices provide sensitivity and performance beyond that considered possible on a front side illuminated sensor with a pixel size of 5.3µm, Quantum Efficiency (QE) of over 80% and excellent sensitivity and performance in the near-infrared (NIR) spectrum (>50% at 850nm). This significantly reduces system illumination costs, or enables very low-light imaging in outdoor camera applications.
-
Product
Machine Vision Cameras
Manta Series
-
High-performance industrial cameras with a large choice of sensors, modular options and built-in image optimization. VGA to 12 Megapixels. CCD and CMOS (Sony, CMOSIS). Up to 125 fps. NIR versions, board level option.
-
Product
X-Ray Detector
Cmosaix CMX4343
-
The technology used for the Cmosaix CMX4343 x-ray detector is based on a large array of CMOS cameras and sophisticated mathematical algorithms that produce superior X-ray imaging and enable new applications that were not possible before, at a fraction of the cost of existing technologies.
-
Product
3.4 MP GMSL Camera (supports Upto 15 Meters)
NileCAM30_TX2
-
NileCAM30_TX2 is the four board solution containing the camera module, serializer, deserializer and TX2 base board. This camera is based on AR0330 CMOS image sensor from ON Semiconductor®. The NileCAM30_TX2 comes with 3 meters or 15 meters coaxial cable with FAKRA connector at both ends of serializer/deserializer board. The NileCAM30_TX2 has an S-mount (M12) lens holder which allows customers to choose and use the lens according to their application requirement.
-
Product
Low-Noise DC Bias
-
Imaging devices, such as CCDs, IR FPAs, and CMOS image sensors, require DC bias with very low electrical noise to prevent contamination of the image. Image quality can also be enhanced by carefully tuning each bias voltage to extract the maximum signal/noise ratio out of an array. Pulse Instruments has decades of experience providing DC bias supplies with the flexibility required tocharacterize and test a variety of devices while maintaining the noise immunity required for satellite and astronomy applications.
