Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
product
iHawk Real-Time Platforms
iHawk is Concurrent’s high-performance, real-time Linux-based computer platform for time-critical simulation, data acquisition and process control applications. iHawk symmetric multiprocessors feature from one to eight x86 processors and up to 1 TB of memory in a single rack mount or tower enclosure.
-
product
PXI Resistor Module 2-Channel 1.5R to 1.02k
40-293-021
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Fast Transient Burst Simulators
FNS Series
A simulator to reproduce fast repetitive high frequency pulses which are generated when switching ON/OFF electric current on the inductive load. International Standard IEC 61000-4-4 defines immunity tests for power supply lines or I/O signal lines against fast transient repetitive bursts. Also adopted as a Japan Industrial Standard.
-
product
Altitude Chambers
ESPEC can provide custom-built chambers for simultaneous testing of temperature and low-pressure altitude conditions. Two common applications are: Testing of avionics or other aerospace equipment to simulate actual conditions it might experience. Simulation of high-altitude conditions like might be found in mountainous regions.
-
product
Simulation Software For Cyclic Voltammetry
Digisim
Cyclic voltammetry can readily provide qualitative information about the stability of the oxidation states and the electron transfer kinetics of a redox system. However, quantitative studies using cyclic voltammetry (e.g., mechanistic investigations) are more difficult and typically require the use of simulation software. A number of methods have been developed for the simulation of cyclic voltammograms. Of these methods, the fast implicit finite difference method has been shown to be the most efficient, stable, and accurate, and this method is used for the DigiSim simulation software from BASi®.
-
product
Controllable, Programmable Clocked AC Source
EAC-AFV
*Output from 15kVA to 2000kVA*Output voltages 0VAC to 700VAC / 1000VDC per phase*Maximum currents up to 2000A per phase*Simulation of 1- and 3-phase networks (worldwide)*Variable frequency of up to 2000Hz, sine, square, triangle*Indication via graphic display
-
product
Regenerative Grid Simulators
Chroma Systems Solutions, Inc.
Rigorous testing to industry regulatons and standards for the safe operation of on-grid products.
-
product
Transformer Rated Metering Site Training Bench
Model 8833
The PowerMaster® 8813 is a true 3-phase training simulator for metering technicians to help improve their troubleshooting skills for applications encountered in the field. The Model 8813 provides a safe, controlled environment to help the trainee accelerate their education in meter testing and wiring verification. The training simulator also features the ability to simulate over 28 commonly found metering errors in the field. Paired with the Training Administrator Station (TAS), the bench can be controlled remotely over a closed WIFI network, and each trainee’s performance is recorded and time stamped for every session.
-
product
MXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5181B
Take your devices & designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading output powerThoroughly test receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
product
IEC60529 IPX1/2 Rain Resistance Tester
IPX12A-600
Shenzhen Chuangxin Instruments Co., Ltd.
The IEC60529 IPX1/2 Rain Resistance Tester is designed according to the <> of IEC60529 standard, GB7000.1 and GB4208-2008. IEC60529 IPX1/2 Rain Resistance Tester is mainly used to simulate the product under the condition of the rain climate to test the products’ physical properties.
-
product
Torque Analyzers & Sensors
If torque tools slip out of calibration, that could impact the quality of your products. Having an accurate way to regularly test calibration onsite is a great way to reduce risk and ensure safety. With Mountz torque analyzers and sensors, you can test tools before they go into service every day. This prevents employees from working with miscalibrated tools and enhances quality management. It’s also more efficient to use your own torque testing equipment since you can evaluate your tools without sending them to a laboratory. Whether you want stand-alone sensors for hand and power torque tools or run down adapters that simulate actual joint conditions, Mountz has many options to choose from.
-
product
Pattern Conversion
Wave Wizard
Wave Wizard generates a test program according to device spec. It avoids the inherent problems that exist when trying to force an event-driven simulation into a constrained ATE test program, by considering device perspective.
-
product
PCI Strain Gauge Simulator Card, 6-Channel, 3k
50-265-106
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Eurocard Plugbord
E160-6U-3
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Overall voltage and ground plane each side with 0.085" diameter clearance around each hole.. Solder coated for user convenience. Use T123 eyelets to simulate plated-thru holes committed to voltage or ground planes. Row and column legends provided.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-055
The 40-297A-055 (PXI) and the 42-297A-055 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
43-752A-912
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-252-010
The 40-252-010 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
PXI Precision Resistor Module 4-Channel, 2 to 13.6k
40-297-131
These PXI precision resistor modules provide a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Pack Testing
PEC offers a 600V-600A and a 1000V-500A system with either 1 or 2 channels. The systems are programmable using the standard PEC LifeTest application, offering a user-friendly environment for configuring and analyzing drive cycles and other energy storage simulations.
-
product
Software Tester & Test Manager
With their ability to replicate all types of networks (i.e. Wide Area Networks, the Cloud, over Wireless, Radio and Satellite links etc. ) iTrinegy network emulators provide testers with the ability to test application performance in a realistic simulation of the target network environment.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-016
The 40-297A-016 (PXI) and the 42-297A-016 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 1.8 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
product
Communication Network Lab (5G, 4G, 3G, 2G, IP, TDM)
GL’s End-to-End Wireless Network Simulation Test Suite provides you an advanced full-fledged “Live Network” at your company premises in any customized package to suit test requirements.
-
product
Acoustic Measurement Systems
Even AuSIM's audio simulation is only as good as the model parameters within the simulation. For AuSIM, deriving optimal model parameters begins with studying the acoustic world around us. The AuSIM3Dtm display systems synthesize a virtual aural environment from parameters based on the physical world. But the same techniques can be applied to reverse the process and extract parameters from the physical world to use for later synthesis.
-
product
V2X Test Tools
Validate and verify your V2X application with our Mx-Drive Mobility Simulator. Use the Mx-DSRC Compliance tester for USDOT certification.
-
-
product
Stability Chambers
Lunaire Environmental is a leading manufacturer of steady state and shelf life testing chambers and walk-in rooms which provide constant climate testing and meet ICH guidelines. These steady state chambers and rooms are perfect for long-term material testing on packaged products in controlled temperature storage. Lunaire steady state climatic test chambers are also ideal for research facilities and laboratories because they simulate wide range of temperature, and temperature and humidity environments. Click here for an overview brochure on Tenney and Lunaire equipment offerings.
-
product
AC Source
AFC
The AFC Series products are single and three phase AC Power sources ranging from 0.5kVA to 2000kVA. This AFC series has a continuous and adjustable output voltage between 5~300V. This allows for quick and convenient 3 scales of preset voltage for high and low voltage simulation. Power is supplied by state-of-the-art IBGT pulse width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance. With up to 90% efficiency the AFC minimizes heat dissipation so less infrastructure cooling is required.
