AC Current Clamps
wrap around conductors to measure current.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
AC Load Bank (Rack Mounted)
K-1000 Rack Mounted
-
Kongter Test & Measurement Co., Limited
Rack mounted resistive load bank is widely used in data center to simulate electric loads and dissipation of IT systems. These load banks are controlled by sectional steps with customized setting. Users could set power and time as per their needs with easy operation.
-
Product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
-
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
Product
Current Transformers
Sensors
-
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
Product
Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.
72-2985
-
The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.
-
Product
DC current Sensors
CTH
-
The CTH sensors convert dc current to an isolated voltage output, the CTHR sensors convert ac current to a dc output signal proportional to the Arms. All popular process control voltage and current loop outputs are available. Through hole or split core options mean that connection is non-intrusive and straightforward. The available input range of the CTH sensors is any value from 5A to 6000Adc.
-
Product
AC High Voltage Test Sets
-
We are highly reckoned among clients for manufacturing and exporting an excellent AC High Voltage Test Set. It is specially engineered and developed for performing varied tests on air conditioner. As to satisfy clients' requirements, we can also optimize this test set. Manufactured in accordance with industry standards using supreme grade raw materials, this AC High Voltage Test Set is offered to clients at industry leading price. Before the final dispatch in market, this test set is stringently tested on varied quality parameters.
-
-
Product
Current Clamps
-
Due to its variable measuring functions, the digital clamp meter can be operated universally. Useful details, such as the large display, manual or automatic ranging and measurement position lighting, makes operation particularly easy and reliable.
-
Product
AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS) Digital Multimeter
1320
-
± 199.9mV, ± 1.999V, ± 19.99V, ± 199.9V, ± 1200V, 5 Ranges, AC VOLTAGE MEASUREMENT (AC or AC + DC TrueRMS)
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
Clamp Meters
-
Basic functions:AC current: 40/400/1000ADC current: 40/400/1000AAC voltage: 4/40/400/750VDC voltage: 400mV/4/40/400/1000VResistor: 400/4/40/400K/4/40MTemperature: -20 to +750°CFrequency: 10/100/1000Hz/10/100kHz/10MHzDuty cycle: 0.1 to 99.9%Capacitance: 5nF/50nF/500nF/5μF/50μF/200μFSpecial functions:Auto rangingNCVDiodeContinuity buzzerLow battery displayData holdRelative data holdAuto/manual range shiftZeroAuto power-offOverload protectionSampling frequency: 3 times/sMaximum display: 3999Maximum open distance of clamp mouth: 55mmGeneral characteristics:Color: iron gray and orangeNet weight: approximately 274gLCD size: 46 x 32mmSize: 245 x 90 x 33mmPower: 1 x 9V and 6F22Packing content:CartonHandheld bagEnglish manualTesting leadBatteryTemperature probe
-
Product
Leakage Current Tester
TOS3200
-
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
Product
High Insulation Digital Clamp Tester
HCL-5000+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Wide AC current measurements for 0.01A～500A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).・Auto power off function and Splash proof structure.
-
Product
Clamp Meter 6000counts Ture RMS
VA312 /VA315
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Clamp meter Diode Test Auto Range Continuity Buzzer MAX/MIN Value Measurement.
-
Product
AC & DC Electronic Load
3270 Series （350V,1875W~22500W）
-
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
Product
AC Electronic Load
-
AC&DC Electronic Loads are design for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources and other power devices such as switches, circuit breakers, fuses and connectors.
-
Product
3.5 Digit Handheld Clamp Meters
U1210 Series
-
Measurements of electrical distribution cables can be challenging and risky. For cables up to 2 inches in diameter, the Keysight U1210 Series (U1211A, U1212A, U1213A) handheld amp clamp meters (also known as clamp-on ammeters) enable high-current measurements without breaking the circuit. Plus, they provide an extra layer of protection with CAT IV 600 V and CAT III 1000 V safety ratings and include full digital multimeter (DMM) measurement features.
-
Product
Current Sensing
-
A current sense amplifier is a differential amplifier providing an analog output voltage proportional to the current flowing into a load connected on its input.
-
Product
Current Probe/DMM
685
-
The #685 is a great tool for all purpose electrical testing. Applications include: fuel injection systems, fuel pumps, charging systems, electric motors, and most parasitic drains. Capable of measuring as low as 10 milliamps!
-
Product
Current Probe
PA-629
-
*Maximum Current Value: +/- 200ADC, 140A RMS*1mA = 10mA, 100mA (switchable)*Rising Time: 1.2uS*Bandwidth: DC ~ 300kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
Product
Digital Clamp Tester with Big CT window (CE)
MCL-3000D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This handy type clamp tester has the biggest CT window in the world (108mmx128mm) and can measure AC load current (0.01A -3000A) just by clamping the conductor without disconnecting the circuit.
-
Product
AC/DC Clamp Milliammeter (CE)
M-740
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current*Suitable for measurement of 4-20mA DC controlled circuit*DC mV analog signal output*Lowest influence from Magnetization and Terrestrial magnetism*Wide measuring ranges - up to DC 1000mA and AC10A
-
Product
High Current Transformers
-
High Current Transformer is designed to elevate and check the temperature of the conductors at high current levels, in order to simulate the current loading conditions found in electrical circuits. High Current Transformer is designed as an open type transformer that uses the test object as its secondary coil or has 1 or 2-turn self secondary winding. The conductors cores' temperature depends on the short-circuit high current caused by the test object. According to the current going through the test object, the test temperature of the conductor will change. The loop temperature is measured by a thermocouple probe which is directly connected to conductor.
-
-
Product
Digital Arrester Clamp Tester (with Data output)
ALCL-40H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*ALCL-40 is designed to test the diagnostic of OXIDE SURGE ARRESTER.*The least influence from the external magnetic field and noise by triple shielding of CT.*Compliant with IEC6099-5.*Enabled the measurements for 100nA resolution and harmonics current.
-
Product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
785041-01
Current Input Module
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
Product
AC Engine Dynamometer
DA50
-
Power: 50 hp (37.3 kW)Torque: 87.5 lb-ft (118.6 Nm)Maximum Speed: 8,500 rpmConstant Torque Range: 0 - 3,000 rpmConstant Power Range: 3,000 - 5,100 rpmDecreasing Power Range: 5,100 - 8,500 rpmRotation: bi-directional
-
Product
Leakage Clamp Meters
-
Precision Mastech Enterprises Co.
Specialized, high-sensitivity electrical testing tools designed to measure low-level AC current (typically in milliamps, to detect ground faults, insulation failures, and potential hazards without disconnecting equipment
-
Product
Current Loop Expansion Kit
OP-SB85C
-
This expansion kit supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
