Filter Results By:
Products
Applications
Manufacturers
Current Probes
measure AC or AC-DC amperage without contacting conductors.
See Also: Current Sensors
-
product
High Current Probes
*Low internal resistance to minimize arching*PogoPlus bias ball design*High current optimized base material and plating*Higher temperature spring design*Specialized high current tip geometry
-
product
Micsig AC & DC Current Probes
CP2100
Shenzhen Micsig Instruments Co., Ltd.
*Split design, small and exquisite appearance, easy to test *Compatible with all BNC-connected oscilloscopes, adapters can also work with multimeters.
-
product
Current Probes
Innovative DC to 5MHz "positional" current probe capable of measuring currents in PCB tracks, component legs etc. without the need to break the connection or surround the conductor.
-
product
Current Probes | Current Sensors
Sensitivity of Conventional Probes Deliver Precise Measurement of Low Current Waveforms from 1 mA. High-precision Current Sensors, DC to 4 MHz, DC to 20 kHz, up to 50 kHz and load current sensors,
-
product
Broadband Current Probes
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.
-
product
Current Measurement Probes
Comprehensive line of clamp-on current probes covers the entire spectrum of applications, from electrical panels to substations. AEMC Current Probes measure current without interrupting the circuit under test and extend the measuring capabilities of DMMs, recorders, power meters, and loggers. The numerous jaw sizes are designed to accommodate a wide variety of conductor diameters and ranges. Available for AC or DC measurements.
-
product
Current Probes
Com-Power's Current Injection Probes are used for RF conducted immunity testing per IEC 61000-4-6, CISPR 16-1-2, RTCA DO-160 and MIL-STD 461. Current injection Probes are to be used only when there is no commercially available CDN for the type of port(s) to be tested.
-
product
High Current Probes
The maximum continuous current rating of a spring probe is determined by its design, size, and construction. Typical probes are rated from 2 to 8 amps maximum continuously current at working travel. While this is sufficient for most board test applications, higher current applications will require a much more solid and rugged probe to withstand current capabilities of 10 to 150 amps and beyond.Another high current solution is our feed-through plunger probe line. As the name already describes, the plunger moves right through the probe and is made from a single piece, reducing the internal resistance of the probe to a minimum.
-
product
Current Probes
PMI® introduces the convenience of flexible current probes (Flex CTs)! These 5,000A probes come in 12″, 24″, 36″, and 48″ lengths that allow you to easily surround multiple conductor bundles. They are available in sets of two, three, or four for use with different recorders. The Flex CTs are powered from recorder voltage and DO NOT require a battery pack for operation.
-
product
T3CP Series AC/DC Current Probes
T3CP Series
Teledyne Test Tools AC/DC Current Probes are powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range of five current probes includes models with bandwidths up to 100 MHz, peak currents up to 500A and sensitivities to 1 mA/div.
-
product
Eddy Current Probes and Drivers
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
product
Brute High Current Probe
P4301-2R
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
product
CC0550X, 50 MHz, 5 Arms Current Oscilloscope Probe
786846-01
The CC0550X, or Hioki CT6700, is a clamp-on current probe that offers a wide DC to 50 MHz bandwidth and 5 Arms of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor … controllers. The probe requires an external power supply.
-
product
High Current Probes for EV Battery Packs
Up to 500Amps - customized connections - battery pack charging.
-
product
PC Controlled Bench Top Power Analyzer
PA2100
The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.
-
product
Complete Power Analysis System
PK3564-PRO
PK3564-PRO complete Power Analysis System includes PS3550 Power Analyzer, AC charger, Quick-Start manual, deluxe voltage leads, four eFX6000 flexible current probes, SD memory card, CAS3 hard-shell carrying case, PSM-A Software, Mini Line-to-DC Converter, Bluetooth Adapter, USB Communications Cable, and 1-year deluxe warranty.
-
product
Bulk Current Monitoring Probe
MP-50
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
product
30A, 100MHz High Sensitivity Current Probe
CP031A
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Micsig Ocilloscope AC Current Probe
ACP1000
Shenzhen Micsig Instruments Co., Ltd.
*Test Current Range: 0.1A-1000A*Operating Frequency: 10Hz-100kHz*Maximum Primary Current: 2000A (2s)*Output Signal: mV/A*Highest Precision: 1%
-
product
Brute High Current Probe
P4301-1R
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
product
High Accuracy 100 Amp Current Probe
HA100
The HA100 is a compact clamp-on current probe for smaller loads where compact size is important. Its measurement range is from 0.1 to 100 amps AC and is very small which is ideal for locking inside a crowded electrical panel during monitoring.
-
product
Current Probe
DCFlex
Power Electronic Measurments Ltd
The DCflex is an easy to use, low cost, thin and clip-around DC current probe. It is suitable for measuring large DC currents of >2kA. The DCflex takes a single shot measurement of the DC current with a typical accuracy of ±1%. It is important to understand that the DCflex does not provide a continuous measurement of DC current.
-
product
CC30100X, 100 MHz, 30 Arms Current Oscilloscope Probe
785562-01
The CC30100X, or Hioki 3276, is a clamp-on current probe that offers a wide DC to 100 MHz bandwidth and 30 Arms of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.
-
product
Brute High Current Probe
P4301-1Z
Current Rating (Amps): 50Current Rating Remark: 40 Amps for BeCu plungersAverage Probe Resistance (mOhm): 5Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 1,750Overall Length (mm): 44.45
-
product
I-V Measurement Systems
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
product
Current Probe
LFR
Power Electronic Measurments Ltd
The LFR is ideal for power quality applications. It has a small, predictable phase error, for power measurements at 45/65Hz. The wide bandwidth allows accurate measurement up to and even above the 400th harmonic.
-
product
N2782B AC / DC Current Probe, 50 MHz, 30 Arms
N2782B
The N2782B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 30 Arms continuous.
-
product
Antenna Kits
A.H. Systems offers 10 models of portable antenna kits. Each kit provides all the reliable antennas, current probes and accessories needed to satisfy a wide array of customer requirements. Each component has a specific storage compartment in the carrying case therefore, loss and breakage are virtually eliminated. Cables, a tripod with azimuth and elevation head and a tripod carrying case accompany each antenna kit. Click on a model below to learn more about it''s characteristics and included antennas.
-
product
Probes, Clamp-On
EM-6981 | 9 KHz – 110 MHz
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
product
18 Inch Universal Flex Current Probe Accessory
FLIR TA74
The FLIR TA74 adds capabilities, simplifies challenges, and gives you the best readings with your existing meter. The narrow, 18-inch long flexible coil clamp and locking mechanism allows you take measurements in tight or awkward spots – ideal for multiple conductor measurements, double-wrap requirements, and deeper access. The connection is a standard banana plug and the output is a voltage signal, so it’s compatible with most DMMs and clamp meters, regardless of brand.
