Filter Results By:
Products
Applications
Manufacturers
Temperature
a measurement of heat or cold.
-
product
Air Temperature Probe
U1183A
Measure dryer, transport pipe, and surrounding air temperature within the range of -50°C to 800°C.
-
product
Temperature Measurement IR Sensors & Detectors
ST60 LCC
A single-channel silicon-based thermopile in a LCC package for surface mount assembly in a small active area of 0.61mm x 0.61mm. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature chang
-
product
Temperature logger-40 to 85C
TK-4014
This logger is self-contained with an internal temperature sensor. It can measure temperatures between -40 to 85C. The unit is designed primarily for indoor use but is splashproof to IP54.
-
product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
product
E-Type Thermocouple, 32°F to 900°F Temperature Sensor
745690-E002
E-Type Thermocouple, 32°F to 900°F Temperature Sensor - The E-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the E-Type Thermocouple and acquire synchronized temperature data in units of degrees. The E-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
Tribocorrosion Tester
ASTM G119
Tribocorrosion involves studying Wear Evaluation of Protective Coatings. It involves mechanical and electrochemical interactions between components in motion. Rtec Tribocorrosion modules measures inline current, voltage, friction, wear, temperature , down force, ear, acoustic emissions at all times. Currently used by several Fortune 500 firms globally.
-
product
DC/AC Inverter 3000 W
ODS-3000-7154-T
DC/AC inverter with 3000 W from Premium | input ranges from 25.2 - 45 VDC | output at 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
product
Temperature Input Device
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Premium Multi-Sensor Marine Thermal Camera
FLIR M400XR
Especially designed for first responders, the FLIR M400XR offers detailed 640 × 480 thermal video, a long range HD Color camera, and a tight-beam LED spotlight for improved target identification. In addition to active gyro-stabilization and radar tracking, the M400XR’s integrated video tracking can lock onto and follow objects within its field of view. Firefighting mode displays a target temperature meter and isotherms to aid firefighters in battling blazes.
-
product
Infrared Radiometers
Calibrated to a custom black-body cone with a measurement uncertainty of 0.2 C from -30 to 65 C when the sensor (detector) temperature is within 20 C of the surface (target) being measured. Radiometers are only sensitive from 8 to 14 m (atmospheric window) to minimize the influence of water vapor and CO2 on the measurement.
-
product
Temperature Sensor
ITS-7025
The ITS-7025 Temperature Sensor was developed to monitor the temperature of liquid-cooled klystron amplifiers. The sensor is designed to clamp directly to the cooling pipe and provide an analog voltage output from 0 to 10 VDC corresponding to 0 to 100 degC with 2 degC accuracy. Two analog outputs are provided; one for connection to a remote data acquisition system, and a second for local service monitoring. A single +28 VDC (other voltages available) powers the sensor which draws less than 100 uA.
-
product
J-Type Thermocouples Wire, Fiberglass (32 deg F to 900 deg F) 1 m
745690-J001
J-Type Thermocouple, 32°F to 900°F Temperature Sensor - The J-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the J-Type Thermocouple and acquire synchronized temperature data in units of degrees. The J-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
PXI Precision Resistor Module 6-Channel, 3 to 1.51M
40-297-050
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Automotive Digital Multimeter, 1999 Count, Average, Manual Range, 3.5 Digit
72-9275
Full featured multimeter with additional functions for automotive diagnosis. Measures AC/DC voltage, DC current, resistance, frequency, dwell, tach, duty cycle and temperature.
-
product
Outdoor Temperature Sensor
ENVIROMUX-STS-O
Applications from -40 to 185°F (-40 to 85°C). Accurate to within ±0.9°F (±0.5°C). Weatherproof enclosure. High resistance to external influences on the cable due to digital output signal. Re-calibration is not necessary after initial set-up. Quick release waterproof RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,942,123 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
Digital Temperature Sensor
ZET 7021
Digital temperature sensor ZET 7021 is designed for measuring temperature of liquid, solid, gaseous and granular mediums, which are safe for the material of thermocouple casing. Application spheres: heat power energy, chemical and metallurgical industry.
-
product
Temperature Kit
TEMPKIT
The Power Probe Temperature Kit is designed to give readings for ambient temperature and from the wireless Temperature Probe. The Tempkit has a built–in temperature sensor in the base unit, plus a temperature sensor in the remote wireless Probe. This allows for multiple readings simultaneously. One additional wireless Temperature Probe (TEMPPROBE) is available separately, for a second temperature reading.
-
product
Low-Power General Purpose FPGA
Certus-NX
*Up to 39K logic cells, 2.9 Mb embedded memory, 56 18 x 18 multipliers, 192 programmable I/O, one lane of 5 Gbps PCIe, two lanes of 1.25 Gbps SGMII, two ADCs (each 12-bit, 1 MSPS).*Packages as small as 6x6 mm, and in ball-pitch options of 0.5 and 0.8 mm.*Power modes – User selectable Low Power vs. High Performance modes, enabled by FD-SOI programmable back-bias.*Design security – ECDSA bitstream authentication, coupled with robust AES-256 encryption.*Instant-on configuration – I/O configures in 3 ms, and full-device as fast as 8 ms.*Available in Commercial, Industrial and Automotive (AEC-Q100 qualified) temperature grades.
-
product
Precision Barometer
HD3114B
Temperature, humidity and pressure handheld data logger with color graphic LCD display.
-
product
Tinytag Thermohygrometer-20 to+50C /0 to100% RH
TH-2500
The Tinytag Thermohygrometer is a hand-held unit to take spot readings of temperature and relative humidity. Readings are communicated via a clear LCD display. Temperature can be displayed in Celsius or Fahrenheit in 0.1 degree steps. The unit can also function as a data logger when used in conjunction with Tinytag Explorer and a PC download cable.
-
product
Coax, Contact, Receiver, 20/26 GHz, SF142B, 90 Series modules only
610102109
Primary mating contact 610102110. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 OhmsFrequency Range DC to 26 GHzVSWR 1.15 + .01 (f) GHz w/ SF142 (20 GHz)Insertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications SF142B Environmental SpecificationsOperating Temperature -65°C to +125°Vibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
CSlaser | CTlaser Series Infrared Thermometer
The infrared thermometers of the optris CSlaser/CTlaser series consist of an innovative double laser sighting, in contrast to many IR thermometers with single lasers which only mark the center of the spot. The two laser beams follow the infrared optical path to mark the position of the measuring field at any distance. At the focus point both lasers are crossing – this greatly supports an exact alignment and reduces measurement errors. The infrared thermometers of this class are mainly used in industrial areas as well as in research and development. Small measurement field sizes are of great importance for precise temperature measurement. A number of different focus versions allow a flexible adjustment for the different applications.
-
product
IR Thermometers
UEi Test & Measurement Instruments
Non-contact IR energy measurement to determine temperature.
-
product
Conformal Coating Inspection
Conformal coating plays a key role especially when electronic assemblies are used in products and systems that perform safety-relevant tasks. The coatings applied to the circuit board protect against environmental influences such as dirt, dust, moisture, condensation, and varying temperatures. Increasing packing densities and the trend toward miniaturization are also making conformal coatings essential. The insulating effect of the coating allows reductions in the distance between conductor paths while also boosting the performance of terminal devices.
-
product
Environmental Testers
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
-
product
Handheld Thermo Hygrometer
HD2101.1
Portable thermo hygrometer, measuring range for temperature -200 °C…650 °C with probes TP47… , for humidity 0…100%RH.
-
product
Temperature Monitors
SIM923A
Stanford Research Systems, Inc.
The SIM923A has selectable 10 µA and 1 mA current sources to provide sensor excitation. Sensor resistance is determined ratiometrically with a half-bridge circuit consisting of the sensor and an internal reference resistor.
-
product
12:1 IR Thermometer w/ K-Type Thermocouple Input
INF195C
UEi Test & Measurement Instruments
The INF195C offers the unique circular laser targeting showing users the exact spot being measured. This 12:1 Infrared Thermometer also offers advanced features including a wider temperature range, K-Type input, selectable emissivity levels, Min/Max, average, differential, a user adjustable alarm and backed by a 1-Year limited warranty.
-
product
Gas Detectors
Great for HVAC professionals, Klein Tools’ Gas Detectors provide quick and accurate results. Whether you need to detect and measure concentration levels of CO and temperature, refrigerant gases, methane, propane, and other combustible gases, you can expect performance and durability from Klein.
-
product
Pen-Type Food Thermometers
This thermometers look like an extra-large needle with a temperature gauge on the end. It delivers reliable results when you want accurate measurement readings of both internal and ambient temperatures. This electronic temperature meter can also be used in getting food temperatures. The probe can measure temperature that range from -50°C~ 300°C (-58 ~ 572°F). The easy-to-read digital readouts has a large screen that quickly displays temperatures in either Fahrenheit (°F) or Celsius (°C) with just one press
