Hybrid Electric Car
conveyance using electric and internal combustion power synergistically.
See Also: Hybrid Electric Vehicle
-
product
Electrical Safety Testing
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
product
Motor Test for Electric Scooters
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual Transfer
M9156CH40
The Keysight M9156CH40 PXI hybrid dual transfer switch module provides an exceptional 0.03 dB insertion loss repeatability, high isolation, low SWR with a long operating life up to 10 million cycles.
-
product
Electrical Test & Measurement Tester
Evolusys Technologies Sdn. Bhd.
• Polarity • Forward & Reverse Voltage• Forward & Reverse Current• Snapback/Thyristor• Open/Short measurement• Contact check (optional-apply for Keithley C series only)
-
product
Electrical Control Panel
We hold expertise in offering wide range of Electrical Control Panel. Our entire product range has high tensile strength and is easy in installation. Our range includes Relay Panel, Transformer Panel, DC Panel, AC Panel, PLC PANEL, and industrial panel. We offer them in varied grades and ensure high strength. Moreover, we offer them in well-defined time.
-
product
Electric Motor Checker
CIE/1001
Cambridge Instruments & Engineering Co.
Housed in attractive wooden body with sunmica finish. For comprehensive check of Rotor and Stator Inductance, Resistance and Insulation Resistance without dismantling the Motor. Only to isolate the power supply.
-
product
Electrical Test Kits
Klein Tools’ electrical test kits combine essential tools for electricians at a great price point. With numerous options depending on what your jobsite requires, these kits are provide professionals with multiple ways to test and troubleshoot.
-
product
Automatic Wind-Solor Hybrid Power Inverter
Applies to electrical appliances (family usage): (power within) various electric light wiring, televisions, refrigerators, computers and other low-power home appliances, fax machines, printers, small electric tools. (Light, TV, refrigeratory, Computer, Fax, Copier)
-
product
Mobilize Electrical Safety Analyzer And Tester
Safe-T Sim®
The world’s smallest automated electrical safety analyzer is designed to perform all electrical safety tests with the touch of one button. Advanced features and half the cost of other automated safety analyzers. User-defined tests with programmable Pass and Fail limits. Wireless technology plus our app provide the capability to control the Safe-T Sim and generate a complete electronic test report right from your smart device!*
-
product
60 GHz, 2/4 Port, Electrical Remote Sampling Head Module
N1045B
The N1045B 60 GHz remote sampling head module is engineered to provide superior measurement accuracy with the highest throughput for testing multi-lane electrical designs.
-
product
Hybrid LX
HLX Series 0.8” x 0.8” x 0.15”
*Surface Mount Package *Ruggedized, Hi-Rel *Hermetically-Sealed per MIL-STD-883 *Extreme Shock and Vibration Tolerance *Output Power to +14 dBm Available
-
product
Customized Electrical Test Optical Inspection
Landrex Technologies Co., Ltd.
Customized Electrical Test Optical Inspection
-
-
product
Electric Vehicle Diagnostics
Innovative diagnostic leak detection technology designed exclusively for battery-electric vehicles.
-
product
Electric Safety Tester
PV-215
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
product
Hybrid Wound Component EST Scanner
19035
Chroma Systems Solutions, Inc.
The quality verification test items for Wound Components consist of AC/DC Hipot tests and Insulation Resistance (IR) tests. Chroma integrates the above tests into the Hybrid 19035 Wound Component EST Scanner series to perform safety tests for motor, transformer, and heater related wound products. The wound component manufacturers performing quality verification testing will not only have reliable quality, but also can control product quality efficiently.
-
product
Robotic Cell for Testing Car Multimedia System
It is necessary to develop an automated system for testing a multimedia device. The system should perform functional testing: testing of physical buttons, touch screen and logic of operation.
-
product
Electrical Testing
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
product
5 kV Electric Motor Analyzer
MCE
The MCE is the most comprehensive static electric motor test equipment available on the market today. Through a series of powerful diagnostic tests, the MCE provides a complete look at the health of an offline motor. The MCE provides critical information to technicians allowing them to diagnose problems early, thus reducing unwanted downtime.
-
product
ITA, I2 Micro ICon, 120/12 Position Hybrid
410130104
The i2 Micro iCon ITA is capable of holding up to 120 QuadraPaddle contacts and up to 12 Micro Power or Micro Coax contacts. Its sleek, 0.8” footprint increases the horizontal stackability. The 30 degree U-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 0.77 in. The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
product
Tester Electrical Interfaces
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
product
Electrical Fast Transient Pulse Group Generator
SKS-0404IB
Shanghai Sanki Electronic Industries Co., Ltd.
Electrical fast transient pulse group generator SKS-0404IB fully complies with the new standards of IEC61000-4-4, EN61000-4-4 and GB/T17626.4; provides pulse test voltage up to 4500V, which can meet various product standards Severity level ; pulse frequency up to 1MHz, and continuously adjustable; imported discharge switch, high precision, long life, good reproducibility; using 7-inch true color touch screen control, convenient for users to directly program and control.
-
product
Dual Servo Electrical Test Fixture
TA-334001
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
-
product
Hybrid & Combiners
*High power handling 500W per port with High in-band isolation at 30 dB minimum and 32 dB typical*Very low PIM <-160 dBc with low insertion loss*Outdoor rack unit with DC/AISG Input pass through on all ports*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
product
Electric Tool Life Tester
Guangzhou Jumho Electric Co., Ltd.
Electric Tool Life Tester loads various periodic signals, such as constant current, constant torque and revolving speed etc, to a single electric tool until it is completely ruined, comparing historical data for further causal analysis.
-
product
Portable Charging Facility Testing Platform For Electrical Vehicle
PONOVO has long-term follow-up technology in China and abroad. Based on its own mature intelligent power detection equipment, and according to its own advantages in the field of new energy, PONOVO could be able to provide users with professional new energy test system solutions.
-
product
33/60 GHz Dual Electrical Channel Module
N1040A
The N1040A is a dual electrical channel plug-in module for the N1000A DCA-X mainframe and provides two electrical channels with maximum bandwidth of 33 or 60 GHz, based on the option selected.
-
-
product
Digital Battery & Electrical System Analyzer w/Printer
726
*Accurate Battery & Electrical System Tester *Features programmed test for new Start/Stop Batteries 3 Testers in ONE! 1) 6 & 12 Volt Battery Tester + 12V Start/Stop Battery Test 2) 12 & 24 Volt Charging System Tester 3) Alternator-Starting-Charging System Tester *Wide Testing Range from 40 to 2,000 CCA *Built-in Printer - print the results for permanent service records *Removable/Replaceable Cable Set *Patented Dynamic Resistance Technology
