-
Product
Universal In-Line Test Platform
-
UniLine brings 20+ years of test & quality experience to your manufacturing floor and test automation delivers accurate results, without bias. By standardizing test, product quality improves as costs decrease. Equipment becomes understandable and manageable across departments and station support becomes simple.
-
Product
System
SpecMetrix
-
SpecMetrix systems by Sensory Analytics were designed from the ground up to precisely measure the absolute thickness of just about any coating on any substrate. All our systems are flexible for use in virtually any manufacturing environment. They provide coating thickness data of unprecedented accuracy—helping manufacturers reduce costs by optimizing coating process control and product quality. Our systems are easily configured to measure webs, coils, flat sheets, small samples or finished parts.
-
Product
Special leak test, pressure testing machines and systems from TQC
Leak Testing
-
TQC have supplied automatic leak test / pressure test equipment for over 25 years. The supply has included simple manually connected leak test fixtures to fully automatic, high speed production leak test facility. TQC supply leak testing equipment to meet the customers requirements.
-
Product
WEIGHING SYSTEM TESTING
1006
-
The Tester 1006 has a simultaneous control function of up to 4 load cells in any weighing system, upload and download function for programming the DAT and MC 302 series instruments, but it can also be used as a Calibrator and Peak detector. It is very useful for the correct mechanical installation and for fault diagnosis. The Tester 1006 is supplied as standard with cable for connection to our junction boxes / sum mod. CEM 4 / C and CGS 4 / C. Simultaneous display of the signal of each individual load cell allows to control the entire weighing system, weight distribution, overloads, faulty cells and faulty connections. OUT OF PRODUCTION. Pavone systems provides a new version of Tester 1006: Tester 1008.
-
Product
Material Compatibility Test System (MCTS)
-
Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:
-
Product
Test Handler
M4872
-
Improve Efficiency in High-Volume Manufacturing and Device Characterization.
-
Product
Haptic Testing System
-
The Air Ventilator Haptic Test System performs automatic functional tests on air ventilation components to measure the force necessary for the execution of movements in the different components of the part. The movements are performed by a 6-axis robot that forces the components of the part to follow the desired routes while storing data on the force expended. This particular machine tests movable fins and knurled wheels by performing four test motions on each fin and two on each wheel.
-
Product
AUTOMATIC WINDING TEST SYSTEM
VE9036SU
-
6 CHANNEL Microprocessor based Automatic Test System for Automobile Coils, Magnetos, Alternator, Motor Winding. Can Test : Impulse Winding Tester (IW), AC/DC HiPot, Insulation Resistance (IR), Inductance (L), DC Resistance (DCR)
-
Product
Fully Automatic Eddy Current Crack Test System
ROTO-SCAN
-
Foerster Instruments, Incorporated
The fully automatic crack test system ROTO-SCAN was specially developed for the testing of rings. The mechanical equipment has been developed for the gentlest possible handling of the test pieces and features a compact and low-maintenance design. The test probes seamlessly scan the inner and outer contours of the test pieces, thus ensuring 100 % testing of the rings.
-
Product
Vision Systems
-
Robust and powerfull Vision controllers that can operate with single or multiple cameras connected to it. The cameras acquire the images and send them back to the vision controller for analysis and an output/judgment.
-
Product
PIM Test Systems
-
AWT's Portable PIM testers are powerful yet compact tools for testing and analyzing telecommunications network infrastructure. These testers are ruggedized and can withstand harsh environmental conditions. they are accurate, reliable and easy to operate and they provide a wealth of features ideal for work in the field. Built-in Distance-to-PIM option.
-
Product
Accelerated Life Test Systems
-
Test systems for accelerated life testing and product burn-in utilize Intepro’s electronic loads that are ideal where high power bulk loading is required. Characterization applications within Telecommunication and Aerospace sectors benefit from Intepro’s environmental stress screening (ESS)/Burn-in solutions
-
Product
Instrumented Pendulum Impact Testing System
JB(INSTRUMENTED)
-
Jinan Testing Equipment IE Corporation
JB-450I/750I Instrumented Pendulum Impact Testing Machine is equipped with high precision instrumented strain-gauged striking edge & high-speed data acquisition system. This instrumented test system can measure the force of a test specimen during an impact event. Then, the instrumented test data can be used to calculate the energy absorbed by the test specimen. In addition, the crack initiation and arrest loads can be used in fracture mechanical models.
-
Product
Management System
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Monitors all systems from receiving sample to consumption, including coal truck, coal yard and equipment of sampling, sample preparation and analysis for fuel.
-
Product
Integrated 5G mmWave Test System
IQgig-5G
-
The IQgig-5G is a fully-integrated, non-signaling solution for testing 5G mmWave products at both the 28 GHz and 39 GHz frequency bands. All signal generation, analysis, and RF front-end routing hardware are self-contained inside a single chassis. The IQgig-5G is license-upgradeable to support the pre-5G and 3GPP standards evolution with up to 1 GHz of tester bandwidth. The IQgig-5G solution has three bi-directional source and measurement ports each with 2.92mm connector coaxial interface.
-
Product
Sputtering Systems
-
Known for precision and cleanliness, Veeco Ion Beam Sputtering (IBS) systems are ideal when engineers need tight control over film thickness, composition, and optical performance. Using a focused ion beam, IBS dislodges atoms from a target, depositing them onto a surface in smooth, ultra-uniform layers.
-
Product
Small Drop Test System
KRD41 series
-
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
-
Product
Vibration Test Systems
G-0 Series
-
The G-0 Series Vibration Test Systems consist of all-round, rugged, high quality vibration generators energy-efficient solid-state PWM power amplifiers, ideally suited to any vibration tests requiring high reliability such as MIL, IEC and JIS standardized tests for aircraft, automobiles, electronic components, electric apparatus and aerospace equipment.
-
Product
Modular Battery Test System
-
This modular battery test system provides for manufacturers versatile testing possibilities. Due to modularity it allows easy configuration of battery testers for a wide range of different power levels.
-
Product
System Components
-
System components and accessories complete the Bender product portfolio:Coupling devices for ground-fault monitoring at high voltages, analog measuring instruments, power supply units, interface converters and interface repeaters.Please contact us for advice regarding these and other system components.
-
Product
Steering Module Test Systems
-
Steering test systems for quiet evaluation of rattle, NVH & performance issues – non-hydraulic. The MB Dynamics Steering Module Test Simulator family of technologies (SMTS) is an assembly of components and software designed to facilitate the quiet testing, development, troubleshooting, and auditing of a variety of steering gear and steering column assemblies — collectively referred to here as steering modules (including components).
-
Product
Test Instruments
-
Test instrumentation from COTS to custom, including VXI, PXI and LXI-based platforms.
-
Product
Magnetostrictive Level Transmitters
-
ABB's K-TEK level products' patented sensor technology allows the LMT series transmitters to be used in the most challenging of industrial level applications such as interface measurement, compressor level and separator level applications. In addition, the LMT Series Level Transmitters are the only magnetostrictive level transmitters in the world to be certified for use in SIL2 and SIL3 systems per IEC61508.
-
Product
Backplane Test System
402LV
-
Very High Pin Count Level IV Backplane Test System. To ensure that Testronics maintains its leadership position as the premier supplier of backplane testers, we will be introducing our solution to testing high pin count / very large backplanes, the Model 402.
-
Product
High-Temperature Test Systems
-
HT-PEM (high-temperature polymer electrolyte membrane) technology represents a further development of PEM fuel cell technology. Unlike conventional PEM fuel cells, which operate at lower temperatures, HT-PEM fuel cells can reach temperatures of up to 200 °C.
-
Product
Burn-In Systems
OPTIMUM Series
-
Advanced Microtechnology, Inc.
The OPTIMUM product line of burn-in systems has a model to meet your individual testing requirements. Please select one of the models below for more specific information
-
Product
Vision System
Project X
-
Project X is different. It utilises a totally new, patented technology XY scale, that records not only X and Y position but also any rotational movement of the camera system. In addition, this is an absolute scale system, which means as soon as you switch on the machine it knows exactly where it is - no need for referencing. The camera is free to glide around the measurement area mounted on a simple air bearing system, without any worry about constraining the mechanics to avoid losing accuracy.
-
Product
MEMS Testing System
BK3010V2
-
The BaKo BK3010V2 is our updated MEMS Tester, based on our C-Mic tester, the best selling BK3010. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is very easy and can be done in a few minutes. In addition, the new BK3010V2 can be connected to a computer so you can keep and view compiled data and track trends in variations in your C-Mics.
-
Product
Sound Level Meter
831-LOWN
-
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
