Backplane Test
-
Product
3-in-1 Test System
CIBANO 500
-
CIBANO 500 combines a micro-ohmmeter, timing analyzer, and a coil and motor supply. All important CB tests on all types of CBs can be carried out even when a station battery is not available.
-
Product
RAMP TEST SET
AN/USM
-
Tel-Instrument Electronics Corp.
The AN/USM-708 Multi-Function Test Set provides unsurpassed reliability and ruggedness designed by an established and well recognized company with 50 years in the design and manufacture of aviation ground support and bench test equipment.
-
Product
D-Mic Testing System
BK3012V2
-
Easy to use and faster than human testers can load, the new BK3012V2 is the upgrade of our popular BK3012 D-Mic tester. Setup is even easier than for the BK3012 and you can enter specifications and be ready for testing in a few minutes. As well as testing, the BK3012V2 can be connected to a computer, so you can keep your results and analyze them for current quality and trends over time.
-
Product
Transportation Bounce Test System
KRD51 series
-
Bounce testing simulates the constant loose cargo state during truck transport. Often times, containers carrying military and civilian hardware (such as: medical supplies, electronics, weaponry, communication devices) travel for extended periods of time and must be transported off-road. All of these items must maintain functionality upon arrival at their destinations.
-
Product
Compliance Testing Services
-
Compatible Electronics is the largest commercial compliance test lab in Southern California, with four test locations, 10 Open Area Test Sites (OATS) and 7 Semi Anechoic Facilities. All open field sites (OATS) are in low ambient areas, which is ideal for radiated emissions testing.
-
Product
Laboratory Test Equipment Temperature Cycling Steam Aging Test Chamber
-
Shenzhen Chuangxin Instruments Co., Ltd.
Steam aging test machine is used to test and determine the parameters, performance of electrical, electronics, other products and materials for high temperature, low temperature, or the temperature of the thermostat test environmental changes.
-
Product
ZY-3 Needle Flame Test
ZY-3/ZY-3S
-
According to IEC60695-2-2 and IEC60695-11-5, ZY-3/ZY-3S Needle Flame Test is applied in the production and quality control department of lighting instrument, hyperpiesia electrical apparatus, domestic appliance, machine electric appliance, electrical machine, power tool, electronic instrument, electrician instrument and technical equipment. Also, it is fit for the industry of insulation material, engineering plastics and solid combustible material.
-
Product
Gravity Test Handlers
-
Microtec offers a wide variation of customizable gravity handlers. The focus of our systems is based on the approach to provide 1 system for many different applications. By pursuing continuous improvements and setting the objective to provide our customers the most convincing test handlers, we are always driven to push our products and its features to the limits and exceed traditional boundaries.
-
Product
Automatic Test Software
EasyTest 2.0
-
EasyTest © 2.0 is a set of common test automation software platform, with the definition of test engineering, test process editor, test program generation, test execution process, test data on a network share as one of the functions. Using EasyTest © 2.0 can easily set up a large network systems and ground test integrated test system, you can build standalone automatic test system, or automatic control equipment R & D engineers, and other data stored for use in research and development.
-
Product
Aircraft Test Set
CA-2100S-07
-
The CA-2100S-07 is a bench mounted, modularized and computer based test set used to service all types of aircraft electronics. It simulates the aircraft environment and replaces a myriad of specialized test fixtures found in the industry.
-
Product
Flexible Test Environments and Integration Services for your Integrated System Tests
TESTERLYZER® Frame 4.0
-
The TESTERLYZER® Frame 4.0 provides a flexible test environment for vehicle control units in an integrated system and is easily accessible from all sides. Customized adaption is provided for panel designs, control unit holders and cable adapters. A TESTERLYZER® I-Box 4.0 is a standard component of the TESTERLYZER® Frame 4.0 and provides the basis for a wide range of structures for the testing of control units, software and services relating to vehicles in research and development. The backbone of the I-Box provides all signals required with distribution to standardized adapter sockets and interfaces. The modular assembly structure ensures swift and safe setting up of the required test environment.
-
Product
Adhesion Tester, Adhesion Testing Equipment, Adhesion Peeling Test
SG-P08-3
-
Adhesion tester, adhesion testing equipment, adhesion peeling test.This tester is used to testing the strength of the adhesion of stuck-on and moulded soles at.The toe and heel in the shoe factory and Laboratory.
-
Product
Mobile Application Testing
-
Mobile Application testing involves the testing of applications in mobile devices. The applications are tested for functionality, performance, usability, etc.
-
Product
In-Circuit Test (ICT)
-
Analog components (resistance, capacitance, inductance, diodes, transistors, etc.) as well as complex digital components can be tested in the ICT. Compared to other test methods (e.g. flying probe), the in-circuit test enables very short test times (= high assembly throughput) combined with a very high test coverage.
-
Product
Semicon Test Probes
-
Fine pitch, 0.20 mm [8 Mil] - single & double ended - non-rotating - kelvin - RF - high performance.
-
Product
AC Hipot Test Set
-
Weshine Electric Manufacturing Co., Ltd
AC Hipot Test Equipment for Dielectric Withstand Test are suitable for 50 / 60 Hz AC testing of low capacity test objects. Optionally, these units can also be upgraded to function as DC test sets by mounting the rectifier attachment on top of the transformer.Weshine® AC Hipot Test Set for AC hipot test can be equipped with a rectifier attachment for DC voltage testing.Typical application areas:Testing of cables Testing of switchgearTesting of transformersTesting of CP & PTTesting of MV systems
-
Product
Testing & Quality
-
The solar simulator, electroluminescence and hi-Pot testers are the main machines used to test photovoltaic modules. These machines can be positioned at the end of the production line and along the production chain to keep the quality and efficiency of the photovoltaic modules under control after the most sensitive production phases. Each machine uses the best technologies in order to guarantee the best and most accurate measurements.
-
Product
DC High-Voltage Test Device
PGK 25
-
Cable testing with the BAUR PGK 25. Cables must be tested in compliance with the national and international standards. This applies before the commissioning of new cable networks. The portable BAUR PGK 25 cable test device is used for DC voltage testing in low- and medium-voltage cables. It is characterised by its low weight of only 16.5 kg, by the easy operation and solid construction for onsite use.* Compact device for DC voltage testing with negative polarity* Continuously adjustable output voltage* Perfect for mobile use
-
Product
Pre-Certification Testing
-
Gain confidence that your product passes certificationVerify your product qualityTest specific areas
-
-
Product
Bench Top Test Set
WesTest-3000/BTTS
-
WesTest Engineering Corporation
*PXI Based*Test Requirement Driven*Core Capability Consistency*Software Standards- ATML, IEEE
-
Product
Temperature & Humidity Testing
-
Trialon routinely test products for the automotive, military, medical, aerospace, heavy truck and customer markets in our facilities in Michigan and Indiana.
-
Product
Test Port Cable, 1 Mm
11500L
-
Connect test ports to devices, fixtures, or probe tips with this 24-cm cable featuring a return loss of 16 dB minimum.
-
Product
Miniature Vibration Test System
G-2 Series
-
The G-2 Series Miniature Vibration Test System, though compact & handy, consists of a sweep oscillator, sine controller, power amplifier and vibration generator, thus suited to a variety of applications; calibration of sensors, standardized vibration tests for small parts, school teaching materials and modal analysis. The G-2002 is handy, with all the composed units being incorporated in a portable case.
-
Product
Test Contactor
RF Scrub
-
RF Scrub™ Test Contactor’s innovative design combines an extremely short signal path (0.90mm test height) with high wear resistance pins that can operate in a wide temperature range.The RF Scrub Test Contactor’s long-life, elastomer free design and easy field maintainability makes it an optimal solution for testing of high-performance devices.The RF Scrub design minimizes load board wear and with the unique pin base material and plating, the cleaning intervals can last up to 100,000 cycles.
-
Product
Test & Measurement
-
High-performance surface and dimensional analysis tools for industry and researchers
-
Product
Blockchain Application Testing
-
Blockchain has revolutionized the approach businesses are conducted and provides enterprises the great opportunity to track assets, collaborate and share information. Diverse verticals like retail, finance, and healthcare are reaping the benefits of blockchain distributed ledger technology. The blockchain apps have now gone way beyond crypto-currencies like bitcoin and other decentralized payment modes or systems.
-
Product
Electro-Optical Test Software
INFRATEST
-
INFRATEST is a powerful software for testing IR cameras, visible and NIR cameras, ICCDs, goggles and laser rangefi nders. Based on video acquisition modules compatible with a wide range of communication protocols, including LVDS, Camera Link, GigE Vision and all types of analog formats – CCIR, PAL, RS170, NTSC, INFRATEST acquires, displays and analyzes the video signal from all types of electro-optical devices.
-
Product
Manual Test Fixture (MA)
MA 2013/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 25,00 kg
-
Product
802.11be Test System
IQxel-MX
-
Next generation wireless devices Access Points, CPEs and client devices like smartphones or tablets based on the IEEE 802.11be EHT (Extremely High Throughput) standard require stringent RF performance to meet the latest standard requirements.
