-
Product
Cable Fault Meter
-
A cable fault meter can locate open power cables, either live or dead (without current), with voltages up to 300 V. A cable fault meter can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power from the cable which is being tested. Many cable fault meter devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A
40-191B-012
Fault Insertion Unit
The 40-191B is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
VALVE & BOX LOCATOR
7-T
-
Rugged "Cycolac" instrument housing and detection headTelescoping HandleVisual Meter & Battery TesterBuilt-in speaker, signal and battery test meterOne sensitivity control knobBalanced and lightweight Adjustable extensionSet of stereo headphones3 Replaceable "AA" Alkaline batteriesDependable
-
Product
Earthing Resistance Tester
JYD-10A
-
transformer neutral grounding resistor is the vital need in medium voltage AC distribution network that are also called by different names like Neutral Earthling Resistors. They are taken into use to limit the current that would flow through the neutral point of a transformer or generator in the event of an earth fault. They are also used for resistance grounding of connected generators and transformers.
-
Product
Rebar Locator
Profoscope +
-
The Profoscope+ is a fully integrated rebar locator with data storage. To increase the efficiency on the construction site this enhancement of the Profoscope not only offers real time visualization of rebars, but also automatic data collection. Writing down measuring results of testing series is a time consuming business that can be an unnecessary source of errors. The various data storage modes of the rebar locator Profoscope+ make note taking obsolete. This cordless rebar detector is ideally suited for one-handed operations, keeping the other hand free for marking rebars.
-
Product
Precision Locating System
Pathfinder PLS
-
The Pathfinder PLS is RYCOM's Precision Locating System for the damage prevention specialist...
-
Product
Earth Leakage Breaker And Residual Current Device
IGR Series
-
IGR Leakage Current Analyzer is invented as the world first, and also can measure Insulation Resistance (MO) without power cut-off. This patented instrument can analyze leakage current, and display Igr(resistive), Igc(capacitive), and Io(vector sum), Ground Insulation Resistance, and the phase angle between voltage and current. (IGR ELB) - Operates due to Igr. - Properly-operating in spite of IGC in digital era. ( Not tripping on UPS load and Harmonics and noise area) - Possible to go down Igr for safety of people and animals. - Possible to manufacture high sensitive ELB. - Possible to prevent fire from electric leakage current.
-
Product
Non-Trip Earth Resistance Measurement
M73
-
M73 has been developed for operators who mainly work on private installations. M73 is very easy to use, it is very small in size and it carries out all necessary tests to establish COMPLIANCE (and hence ensure SAFETY) of an electric system.
-
Product
Short-circuit and Earth Fault Indicators
-
The Sensorform range of Short-circuit and Earth Fault Indicators detects short-circuit and earth faults on medium voltage underground cables. A wide range of options are available for enclosure type, power source, indicator type, reset method, trip-level selection, auxiliary outputs, and remote indication.
-
Product
Pipe & Cable Locator
505
-
Split box locator, Inductive Operation, Conductive Operation, Locate Unknown Pipes, Peak Method, Null Method, Very Accurate Depth Location.
-
Product
Earth Resistance & Resistivity Meter
MRU-21
-
* earth resistance measurment with 3-pole method, * measurement of continuity of equipotential bondings and protective conductors with auto-zero function - with current 200mA, * resistance measurement using 2-pole method.
-
Product
Pre- Locator
CFL PL4
-
CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.
-
Product
PXI 1A Fault Insertion Switch 11-Channel
40-195-101
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Short Circuit Locator for Power Cables
A910
-
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
Product
PXI Fault Insertion Matrix Modules
-
All of our fault insertion matrices feature a breakout arrangement that allows faults to be attached to the sensor lines via the Y axis. This includes the breaking of a connection or the adding of a series defect – all of which can simulate connectivity problems in the system. The three pin breakout versions allow the connection to be swapped for a “bad” sensor simulation.
-
Product
GPR Utility Locating Tools
LMX100™
-
LMX100™ offers the perfect balance of depth penetration and resolution for accurate locating. Data is collected in Locate & Mark mode; this provides a real-time image in the field to identify utilities and mark their locations.
-
Product
OGI Camera for Hazardous Locations
FLIR GFx320
-
The FLIR GFx320 represents ground-breaking technology for visualizing fugitive hydrocarbon leaks at natural gas well sites, off-shore platforms, liquid natural gas terminals, and more. Its certifications for use in hazardous locations allow surveyors to work confidently while maintaining safety. FLIR designed the GFx320 with the user in mind, offering ergonomic features such as the articulating LCD screen to help you avoid fatigue during all-day surveys.
-
Product
Fault Detection Device in PV String
-
Hanwa Electronic Ind. Co.,Ltd.
◆Very light and easy to carry.◆Possible to find fault areas that can’t find by Voc.◆Measurement Voc and Vc.◆Possible to check data and record the data using Android.
-
Product
Ocean Signal RescueME PLB1 (Personal Locator Beacon)
RescueME PLB1
-
The RescueME PLB1 is the world's smallest 406mhz & GPS enabled PLBOperation of the rescueME PLB could not be simpler. To activate the PLB: Pull the retractable antenna out by its end tab, flip open the spring loaded cover over the activation button, hold the button for 1 second until the lights blink. Visual instructions are clearly printed on the case. When activated, the rescueME PLB1 will transmit accurate position data from its 66 channel GPS for a minimum of 24 hours while the integrated strobe light ensures maximum visibility.Ocean Signal has ensured that rescueME, like all of its other safety products, exceeds statutory requirements. RescueME PLB provides an incredible 7 year battery life, and is covered by a 7 year warranty. Even after more than 24 hours of continuous operation, and when the battery power is insufficient to transmit the satellite signal, the PLB1's homing beacon and strobe light will continue to operate. This high intensity strobe light features a molded lens to enhance the visibility of its efficient LED and it gives a powerful 1 candela light emission.Self-test of the PLB can be carried out with a simple button press with the start of test and results clearly indicated by a green flashing light. The antenna is easily extended like a normal tape measure and can be retracted using the winding mechanism on the top of the unit. This unique feature greatly facilitates user training and familiarization as it is not a one time deployable antenna similar to existing PLBs.rescueME comes with a snap-in mounting bracket and universal rubber mounting strap which can be fitted permanently or with each use. It is also supplied with a detachable flotation lanyard to accommodate all scenarios out of the box.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Fault Insertion Unit
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
Fault finder
The STaff™
-
The staff fault finder is designed to meet the demands of the professional troubleshooter but its simplicity and price make it a tool for anyone needing to locate cable faults. Arrows on the LCD screen direct the user to the fault with pinpoint accuracy. A reference indication also will aid the user in identifying multiple faults when present. Whether you are fault locating utility service line or locating a broken sprinkler wire, the STAFF is the professional's choice.
-
Product
Fault Locator
SNOOPi
-
SNOOPi employs a bespoke optical sensor to detect and discriminate between fault and natural gas.
-
Product
Magnetic Locators
-
Schonstedt is a worldwide leader in designing and manufacturing Magnetic Locators. Using innovative HeliFlux dual-sensor technology, Schonstedt Magnetic Locators detect the magnetic fields present from any buried iron object.
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
Metal Cover Locator
CS880
-
The CS880 Metal Cover Locator is a metal detector that will locate lost or hidden metal objects. It is most commonly used for locating manhole covers through tarmac and grass.
-
Product
Earth Leakage Relay
-
Nippen Electrical Instruments Co.
NIPPEN's Earth Resistance Testers are used for measuring earth electrode resistance, soil resistance, earth continuity, neutral and earth loop resistance, resistance of various components etc.They are used in Railways, Defence, Utilities, Power Plants, Geological Surveys and other Industries.Direct reading type models SET/DET/TET provide direct readings of resistance on moving coil type meters, having a linear scale, 70mm long knife edge pointer and an external zero adjustment.
-
Product
Cable Fault Point Identifier
OCFI
-
Shanghai Tarluz Telecom Tech Co., LTD
Optical Cable Fault Identifier (OCFI) is The latest instrument of optical cable maintenance, repair equipment developed by tarluz, it can identify the physical cable fault location easily. This is an essential tool for fiber optic cable repair!
-
Product
Fault ID & Repair
-
As a manufacturer of bare PCBs, you know that your reputation sits right on top of every board you send out. You have to get them right, but with every PCB you discard, you’re throwing away precious labor, materials, power and time, along with many other costly elements that go to make up your products. That’s why it’s important to know which of your flagged boards are in fact electrically sound, and whether repair is a viable, reliable option.
-
Product
Cable Fault and Test System Vans
-
Whether you are working on-site, in the countryside or an urban environment, having the right equipment available when conducting fault location operations is vital. When the correct tools can be accessed easily, fault-location time speeds up dramatically, and faults can be dealt with more efficiently. Megger’s range of cable test vans offer solutions to the challenges of fault location in the real world, no matter the environment. Our test van systems have been developed in collaboration with end users to ensure that they live up to the standards of daily fieldwork. Our vans are designed to be adaptable to the end users needs so that the most appropriate tests may be carried out for the cable in question, regardless of whether it is low, medium or high voltage.
-
Product
Real-Time Location System
RTLS
-
The new real-time location system „RTLS“ combines high localisation accuracy in an industrial environment with unique technical features which allow a broad use of the system in different applications. It is possible to use RTLS in complex environments for different applications. Tracking and Digitising Production and Logistics Processes manufacturing progress and a transparent material flow.The real-time data about the location and status of the objects available with the RTLS form the basis for networking the parties involved and the logistics processes in their value-added chain.
