BERT
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: Bit Error Rate Testers
-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
Multi-Instrument BERT Software
N4980A
-
The Keysight N4980A multi-instrument BERT software provides the ability to control multiple instruments through a rich Windows-based graphical user interface (GUI). Bit error rate measurements are simple to set up with the intuitive control screens. The software is ideal for setting up and performing parallel BER measurements and jitter tolerance testing (N4980A-JTS) in multi-lane and SERDES devices. You can also create your own patterns using the powerful editing tools built into the pattern editor to meet your unique requirements.
-
Product
4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) With Eye Checker
RB3004
-
*Low cost continuous 4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
Advanced Measurement Package For M8000 Series Of BERT Test Solutions
M8070ADVB
-
The M8070B system software for the M8000 Series of BER Test Solutions can be enhanced by additional software packages, such as M8070ADVB or M8070EDAB to get the best out of the M8040A, M8020A and M8030A J-BERT platforms.The M8070ADVB Advanced Measurement package offers advanced features like automated jitter tolerance test and parameter sweeps, eye diagram measurement or the integration of external equipment such as electrical and optical clock recovery or error analysis using a real-time scope.
-
Product
HDMI/Display Port Checker with 4ch x 12Gb/s Tunable BERT & EyeChecker
RB1204-HDMI,RB1204-DP
-
*Low cost continuous 4ch 1G to 12Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
PAM4 Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
Golight PAM4 BERT integrates a 4-CH or 8-CH multistage pulse pattern generator (PPG) and a highsensitivity error detection (ED) to achieve BER measurement of data transmission in 200Gbps and 400Gbps. PAM4 BERT provide the best solution for automated production testing of 200G and 400G highspeed optical transceiver.
-
Product
Bit Error Ratio Testers
-
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
Product
Multi Channel Bit Error Rate Tester
QSFP+ Tester Rx
-
You want to save time by measuring sensitivity on all four QSFP+ channels at the same time? Here we go: BERT + E/O converter + optical attenuator + optical power meter.Have this four times in two mainframes. Only one clock source is needed.Covers 16G FibreChannel and Infiniband FDR.
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
Multi-Functional Ethernet Test Solution
PacketExpert™
-
PacketExpert™ 10GX is a comprehensive Ethernet/IP test solution supporting industry standard functionalities including wirespeed bit error rate testing (BERT), RFC 2544 / Y.1564 / RFC 6349 tests, packet capture, event-driven triggers and actions, traffic playback, impairment generation, stacked VLAN/MPLS tests, and many others.
-
Product
Bit Error Rate Testers
-
The FarSync BERT Tester provides a comprehensive, simple to use, line testing utility for asynchronous and synchronous lines. Standard BER test patterns are used with real time error counters, user controlled error injection, full line test statistics and APIs.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
Bit Error Rate Testers
FarSync BERT Tester – USB
-
A Bit Error Rate sync and async communications line quality tester for a Windows Laptop/PC using a USB port. The FarSync BERT provides a comprehensive, simple to use, all in one, line testing utility for testing synchronous lines from your Laptop. There are no extra expensive modules to buy to test different line types.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Photoreceiver
-
A lightwave digital receiver module designed for OC-192, DWDM, and Bit Error Rate Testing (BERT) of a digital optical link. The LRD-10-M is an O/E converter with post/limiting amplifier module designed for use in receivers up to 12.5 Gb/s data optical transmission systems.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Economical Solution for Test Requiring Fewer Instrumentation Modules.
OPTOWARE-S200 (FOTS-Bench Top Series)
-
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
Product
Pump Laser Diode Driver
S-110
-
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
Product
Receiver Conformance Test Application for IEEE 802.3ck
M8091CKCA
-
Designed to assist and simplify the stress signal calibration used for testing the inputs of IEEE 802.3ck Draft 3.3 chip-to-chip (C2C) and chip-to-module (C2M) electrical interfaces using Keysight M8040A 64Gbaud Higher Performance BERT or an M8050A 120Gbd High-Performance BERT together with Keysight Digital Communication Analyzer (DCA) Oscilloscope or Infiniium UXR real-time Oscilloscope.
-
Product
Single Channel Error Rate Tester
Basic Bert
-
Already as a single channel BERT the PARALLEX® system offers full functionality for testing high speed components. PRBS and user pattern generation and error detection for 2..13Gbit/s.
-
Product
NRZ Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
Product
Multi-Channel Synchronization Module for M8190A, M8020A or M8030A
M8192A
Synchronization Module
Complex testing sometimes requires playing multiple waveforms in parallel (e.g. multi-emitter testing). The M8192A synchronization module allows engineers to synchronize up to 12 M8190A channels and fits into a standard AXIe frame.The M8192A synchronization module also supports testing of high-speed digital busses like PCI Express.Test efficiency can be increased by testing up to 10 lanes with the M8051A and the M8041A BERT modules in parallel. These can be synchronized by the M8192A module.
-
Product
International Test Set
930i
-
The 930i Communications Test Set is a multi function portable unit that features a powerful Next Generation Voice Test Suite. It offers a laboratory quality VF TIMS, a full-featured BERT, RS-232 control and a host of other functions as standard equipment.
-
Product
Serial Bit Error Ratio Testers
-
Developing next-generation technology requires world-class signal integrity and analysis capability. Keysight offers the widest choice of serial bit error ratio test (BERT) products for accurate and efficient characterization, compliance, and manufacturing test for digital interfaces in computer, video, datacom, and telecom applications operating up to 40 Gb/s. Keysight’s breakthrough technology enables you to conquer even the most difficult measurement challenges.
-
Product
HDMI/Display Port Checker with 4ch x 12Gb/s Tunable BERT & EyeChecker
RB1204-HDMI/DP
-
*Low cost continuous 4ch, 1G to 12Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
Single Channel SFP+ All-In-One Sensitivity Tester
SFP+ Tester
-
All in one mainframe to perform a complete sensitivity test on a single channel fiber optic transceiver. Includes Clock source, BERT and all optical modules
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
E1 T1 Tester
NetProbe 2000 PDH
-
New Generation Analyzer for Legacy PDH networksThe NetProbe 2000 E1E3 is newest, state-of-the-art handheld analyzer on the market for testing the legacy E1 and E3 in PDH networks. It includes all features for E1 & E3 BERT and E1 physical layer testing. Automated line monitoring performs autocheck of essential alarms and errors.
