-
Product
MIMO Vibration Control Overview
-
MIMO Testing has gained a huge momentum in the past decade with the development of multiple shaker table systems, the availability of Multiple-Input Multiple-Output (MIMO) controllers, and the readiness of the standards (e.g., Mil STD 810G method 527 and IEST DTE 022 working group recommendation). The Multiple-Input Multiple-Output (MIMO) Control System includes the following:
-
Product
MIMO Tester
-
Qosmotec Software Solutions GmbH
The QPER MIMO Tester is a handover tester einriched with phase shifter that helps engineers to make mobile networks fit for modern standards like LTE or HSPA+.
-
Product
Multiple-Input Multiple-Output (MIMO) FRF Testing
-
EDM Modal MIMO FRF Testing includes a dedicated test setup and operation process flow using multiple simultaneous shakers to acquire FRF signals. Using a large channel count data acquisition system (i.e., Spider- 80X or Spider-80Xi), this shaker excitation method provides much higher efficiency and accuracy for the FRF measurements while minimizing local stresses on the test article.
-
Product
Multiple-Input Multiple-Output (MIMO) Sine Test
-
EDM Modal Sine Testing includes a dedicated test setup and operation process flow using a single or multiple modal shakers outputting a sine wave to acquire FRF signals. The Source Output type is either Swept sine or Stepped sine. The sweep mode can be linear or logarithmic.
-
Product
MIMO Antenna Assembly for Shield Box
HDRF-MIMOST2570
-
MIMO Antenna setup assembly customized for HDRF-series shield boxes
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 400 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.828-04
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
2-In-1 Wi-Fi Tri-Band MIMO Antenna, Covering 2.4/5/6GHz Bands, Support Wi-Fi 6E/7, IP67
AIW-514
-
2-in-1 WiFi Tri-band MIMO antennaDipole antenna with omni-directional radiation patternCovering 2.4GHz/5GHz/6GHz bandsSupport latest Wi-Fi6E/7Screw MountRP-SMA male connectorIP67 waterproof resistant for outdoor
-
Product
USRP Software Defined Radio Reconfigurable Device
-
The USRP Software Defined Radio Reconfigurable Device is built on the LabVIEW reconfigurable I/O (RIO) and universal software radio peripheral (USRP) architectures. It includes a powerful FPGA for advanced DSP that you can program with the LabVIEW FPGA Module. The device includes 2x2 MIMO transceivers or four-channel superheterodyne receivers, supporting center frequencies from 10 MHz to 6 GHz, with up to 160 MHz of instantaneous bandwidth. The USRP Software Defined Radio Reconfigurable Device also optionally includes a GPS‐disciplined oven-controlled crystal oscillator (GPSDO), which provides greater frequency accuracy than temperature- compensated crystal oscillators. Prototyping applications include LTE and 802.11 prototyping, spectrum monitoring, signals intelligence, military communications, radar, direction finding, and wireless research.
-
Product
NI-5793, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782512-01
RF Adapter Module
The NI‑5793 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5793 modules.
-
Product
CPS-8910 , Switch Device for PCI Express
784307-01
Switch Module
PCI Express, Cabled Switch Device—The CPS‑8910 is designed for large multiple-input, multiple output (MIMO) expansion configurations and system control on the PXI platform or software defined radio devices. The CPS‑8910 provides two PCI Express upstream ports and eight downstream ports for seamless system expansion. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel MIMO systems. You also can connect multiple CPS‑8910 switch boxes to a single PXI Express chassis to create massive MIMO systems with a Software Defined Radio Reconfigurable Device. The large data throughput capacity makes the CPS‑8910 an ideal data aggregator for massive MIMO systems. You can use the CPS‑8910 with copper or fiber-optic cables.
-
Product
VXG Vector Signal Generators
-
Keysight's VXG vector signal generators offer the industry's highest output power with ultra-low phase noise for your most demanding wireless and aerospace and defense applications. With the VXG's multichannel architecture, quickly switch from blocker and interferer tests to MIMO and beamforming tests.
-
Product
Propsim Channel Emulation Solutions
-
Propsim Channel Emulation Solutions are versatile and easy-to-use in a wide range of applications including MIMO, Beamforming, WLAN, Aerospace, MANET and MIMO OTA testing.
-
Product
Test Tool for Modern Wireless Communication Devices
ITN 1000 for WLAN and Bluetooth™
-
Functional Test Tool for Modern Wireless Communication DevicesDevelopment, prototyping, validation and production testing of wireless devices supporting the Internet of Things need low cost, easy-to-use test equipment with support for the latest standards:- Wi-Fi 6E: 802.11ax, 2×2 MIMO; 2/5/6 GHz - Bluetooth™: 5.2 BDR/EDR/BLE
-
Product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786856-01
Vector Signal Transceiver
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal solution in both the lab and the production floor. The PXIe-5831 meets the stringent challenges of 5G New Radio, but it is also able to test a variety of cellular and wireless standards such as Wi-Fi 6. In addition, you can easily expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
Product
Software Defined Radio
-
NI software defined radios (SDRs) provide the design solution to rapidly prototype wireless communications systems, which leads to faster results. You can present applications with real-world signals such as multiple input, multiple output (MIMO) and LTE/WiFi testbed.
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.825-02
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-02
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
PXIe-5830, 12 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
787047-01
Vector Signal Transceiver
12 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5830 supports validation and production test into mmWave frequency bands. This vector signal transceiver incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe-5830 helps you test a variety of cellular and wireless standards such as Wi-Fi 6. You can expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
Product
NI-5792, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782511-01
RF Adapter Module
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
Product
Signaling Test Solution
IQcell-5G
-
Purpose built to validate RF parametric measurements, end-to-end throughput, MIMO, mobility, and user experience testing across cellular and cellular capable connectivity devices such as smartphones, CPE’s, laptops, tablets, hotspots & much more.
-
Product
RF Switch Matrices
-
For applications involving the test and measurement of multiple RF components, Teledyne Coax offers Custom Switch Matrix solutions to integrate multiple switches, along with additional components including filters, mixers, and attenuators, as required. These Custom Switch Matrix units can contain SPDT, Transfer, or Multi-Throw Switches in either Multiple Input Multiple Output (MIMO) or Multiplexer (MUX) configurations.
-
Product
Steering Test Equipment: Software & Hardware
-
MB Dynamics delivers steering test equipment to help fulfill a myriad of application test requirements, or jobs-to-be-done. The steering test equipment consists of software for multi-test-head, synchronized MIMO closed-loop control and data acquisition; rotary servo motors for attachment to a steering spline or wheel; electrodynamic shaker systems; long-stroke linear motor actuators; pneumatic actuators; column stands for mounting steering column; gear fixture for mounting the gear; instrumentation (force, torque, displacement, rotary position, acoustic, acceleration); fixtures for mounting gears and columns; brackets, clamps, and fixtures for holding test items; jounce/rebound fixtures and tilt positioners for aligning input forces with tie rods at angles; software and associated data acquisition hardware up to 16 channels for recording, analysis and evaluation of in-lab steering noises and accelerations, road load data acquisition, and general Sound & Vibration analysis; and engineering services to accelerate test effectiveness.
-
Product
2x8 USB Solid State Switch Matrix, 300 KHz To 6.5 GHz
P9165A
Switch Module
P9165A 2x8 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
Multiple Shaker Control
-
EDM Multi-Shaker Control (MSC) is a software option included in the EDM testing package along with VCS. Multiple Shaker Control provides one centralized interface to interact with multiple controllers running separate tests at the same time. Multi-shaker controllers are not time synchronized unlike in MIMO VCS, in which all drives are time synchronized.
-
Product
2X8 USB Solid State Switch Matrix, 300 KHz To 9 GHz
P9165B
Switch Module
P9165B 2X8 USB solid state switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
Antenna Test Chambers
-
Special design for low PIM antenna measurements Shielding > 90 dB Frequency Range 700/1000 MHz to 6000 MHz Residual PIM < -165 dBc (@ 2 x 43 dBm) Up to 6 antenna ports for multi-band and MIMO antennas Standard models for antennas up to 2.7 m length Customized solutions available on request
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/s on 4 DAQ Channels and 4 AWG Channels
DN2.816-04
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.806-08
Digitizer
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
Multi-Port Antennas
-
*Contains between 4-12 ports*Multi-band antennas with separate high and low band ports*Deploy 4x4 (MIMO) on both high and low bands*Independant tilt control for each band
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 250 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.822-02
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
