Trailer Circuit Testers
determine that a trailer's lighting is working. Trailer
-
product
4-Wire Universal Cable/Harness Tester
LX-760+
Shenzhen Lian Xin Technology Co., Ltd.
The system provides English/Chinese free switch operation interface·4-Wire Measurement
-
product
45 Degree Flammability Tester
TF310
TESTEX Testing Equipment Systems Ltd.
45 Degree Flammability Tester, is to determine the fabric flammability (fabric burning test) under controlled conditions, complies with standards like 16 CFR Part 1610, ASTM D1230, ASTM F2100.
-
product
Large Range Resistivity Tester
HS-SFRT
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
product
Electrical Test & Measurement Tester
Evolusys Technologies Sdn. Bhd.
• Polarity • Forward & Reverse Voltage• Forward & Reverse Current• Snapback/Thyristor• Open/Short measurement• Contact check (optional-apply for Keithley C series only)
-
product
High Voltage Breakdown Tester
Model HV-55
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 5 Kilo Volt DC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Gradually.
-
product
Hardness Testers
The QATM hardness tester portfolio covers all standard test methods, such as Vickers, Brinell, Knoop & Rockwell, as well as a wide test load range. The entire hardness tester range is characterized by technological innovation, precise measuring instruments and maximum comfort due to automation and advanced interfaces.
-
product
SCSI CABLE TESTER
ST123
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
product
Production PCB Combinational Tester
The PT100Pro combines ARM Functional Test, Analog Test and Boundary Scan in one platform for testing up to 32 PCBs at a time. The PT100 Pro solves the test challenges and cost requirements of testing small, high-volume PCBs used in the home, mobile, entertainment, automotive and embedded markets. PCBs in these markets are cost sensitive yet require high volume, high fault coverage on leading edge technologies such as WiFi, DDR Memory, USB, Bluetooth, Nand Flash, MPEG decoders, Power Management Units, and MMC/Smart Cards interfaces.
-
product
Hipot & Electrical Safety Testers
Vitrek manufactures two different series of hipot and electrical safety testers. These testers have been designed to fit your testing application. Each series offers 6 different models with a wide variety of test functions and capabilities.
-
product
Oxygen Sensor Tester and Simulator
ST05
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
product
Aerodynamic Filtration Performance Tester
DRK9007C
Shandong Drick Instruments Co., Ltd.
Used to test the gravimetric efficiency performance of air filters.
-
product
Battery Leak Testers
Battery leak testers are crucial tools in the quality assurance process for battery manufacturing. These testers are designed to detect any leaks in battery cells, ensuring that the batteries are safe and reliable for use. Battery leaks can lead to reduced efficiency, potential damage to devices, or safety hazards. By employing sophisticated techniques, such as pressure decay methods or helium detection, battery leak testers can identify even the smallest imperfections in battery casings. These testers are essential in industries where battery reliability is critical, such as in automotive, consumer electronics, and renewable energy sectors, ensuring that the batteries meet stringent safety and quality standards.
-
product
Cable Testers
E448
The EMO cable testers are designed for use in portable and bench mounted applications, including the assembly and testing of cables.
-
product
Spring Back Tester
HTJ-16
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;
-
product
AC/DC Leakage Current Tester
228
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
-
-
product
Module Breakage Tester
MBT
The tester is used to provide confidence that the risk of physical injuries can be minimized if the PV module is broken in its specified installation. The module breakage test is specified in the IEC 61730 (MST 32).
-
product
Hand-held Cable Tester
STM-8
The STM-8 is an economical and versatile hand-held tester designed for the testing of UTP and screened cable for opens, shorts, reversals, miswires, split pairs and cable length.
-
product
RF PHY Tester
TLF3000
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
product
Safety Tester
Safety analyzer is mainly used to provide the test solution for electric car, grid, photovoltaic, electrical appliances, information equipment, medical equipment industry as well as innovative solutions for the various electrical measurement.
-
product
Electric Safety Tester
PV-215
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
product
WAN Tester III
The Telinc WAN Tester III is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, T-3 and E-3 modems,multiplexers, CSU/DSUs, T-1 CSUs, DTUs, NTUs and TIUs. It is supplied with user changeable nickel metal hydride batteries and a built-in charger.
-
product
Weld Testers
The Weld Tester is our most versatile electrochemical monitoring instrument. Housed in a substantial metal case with brushed anodised aluminium front panel and green military specification connectors this equipment looks functional and professional. The top row of connectors are exactly the same as provided on a Gill 12 whilst the bottom row are for the additional weld segments. Using the same Potentiostat, Galvanostat, Zero Resistance Ammeter with integrated Frequency Response Analyser and Sweep Generator as a Gill 12 allows all the tests supplied with the Gill 12 to be supplied with the Weld Tester.
-
product
Electrical Testers
Digital voltage and continuity tester with LCD screenAC and DC voltage testing (7 thresholds) with automatic AC or DC detection, audible continuity and single-pole phase test.
-
product
Hipot Tester
HAL
The HAL Series combines over 50 years of expertise in ensuring the electrical safety of manufactured electrical products.
-
product
PAT TESTER
Precision Mastech Enterprises Co.
The Safety Pat Plus is a handheld battery powered unit suitable for carrying out electrical safety tests.Stores 300 test results and can be battery & mains powered. The instrument is capable of testing surge protected equipment & can test 110V, 230V appliances. It will return true leakage results at both 110V and 230V
-
product
LED Driver Online Tester
LEDLS-60/LEDLS-12
• The tester includes A Group Measuring Module and B Group Measuring Module. The A Group measuring module can test 6pcs LED Driver AC Parameters. The B Group measuring module can test 6pcs LED Driver AC, DC and AC/DC Parameters. • There are 12 windows to display the input and output parameters, it is good for comparing and analyses. • Quick test for all of the parameters in 0.1 seconds. • It can set up the testing parameters PASS/FAIL range, it will have Noise/Light warning if it is Fail. We also supply handle port (Extra cost) • Software communicate with PC (Extra cost)
-
product
Installation Safety Testers
VDE 0100
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP
SCOT MXP measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time in various configurations. The MXP has a special mode to measure Pre-Insertion Resistor (PIR) closing time
-
product
Friction and Wear Tester
EFM-III Series
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
