-
Product
CTGcalc™ Software
-
CTGcalc™ is a Windows application that sets up microwave network analyzers, acquires measured S-parameter data, and analyzes the acquired data for CTG’s various measurement fixtures. CTGcalc™ allows the user to extract complex dielectric permittivity, magnetic permeability, or sheet impedance of the measured specimens.
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
Product
EFixture-B, Advanced Electric Test Fixture
-
The eFixture-B is an advanced electric test fixture designed to deliver maximum flexibility and efficiency in automated testing processes. This innovative system eliminates the need for pneumatic components, providing a purely electric exchange mechanism that simplifies setup and operation. With its compact design and robust build quality, the eFixture-B accommodates a variety of testing scenarios, making it an essential tool for modern electronics testing environments.
-
Product
EAOC, Electric Servo Drive
-
The AOC-E module is an electric servo drive for the automated opening, closing and contacting of mechanical or vacuum test fixtures, aimed at optimizing work processes and increasing productivity.
-
Product
Integrating Spheres
IS-*M
-
• Diameter: IS-0.3M (φ0.3m)、IS-0.5M (φ0.5m)、IS-1.0M (φ1.0m)、IS-1.5M (φ1.5m)、IS-1.75M (φ1.75m)、IS-2.0M (φ2.0m). Other sizes can be designed according to the customer’s request. • The painting of integrating spheres is according to CIE Pub.No.84 (1989) • Material: Pure barium soleplate (BaSO4) • BaSO4 coating: ρ(λ)≥0.96 (450nm~800nm) and ρ(λ) ≥0.92 (380nm~450nm) • Fine diffuse reflection: Reflectanceρ≈0.8 and accuracy of ρ (λ) <1.5% • Build-in lighting holder position: The vertical is for E40, E27 and so on. The horizontal is for T5/T8/T12 tubes. The side assistant opening is for lighting fixtures • Auxiliary lamp position has been built-in. Auxiliary lamp and Auxiliary lamp device are optional • Power cable and socket has been build-in, it is convenient to power the testing lamp • Two photo detector ports, one optical fiber port and temperature sensor hole are built-in • The traditional integrating sphere is assembled by several pieces, Lisun Group developed A Molding Technology to produce the integrating sphere. A molding integrating sphere will be more round and the test results will be more accurate than the traditional integrating sphere
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
LHS2-A, Single-Position Linear Arm Fixture
-
Single-position linear arm fixture, the LHS2-A. Your manual fixture for small assemblies with few needles for small series or laboratory set-ups. Small, extra compact and absolutely uncomplicated to operate.
-
Product
Coefficient of Friction Gauges
M5-2-COF
-
The M5-2-COF coefficient of friction (COF) gauge is an integral part of a COF testing system, typically including a motorized test stand and COF fixture. With a capacity of 2 lbF [10 N], the gauge can be used to measure friction for a wide range of materials, ideal for conformance to ASTM D1894 and other relevant standards. Static and kinetic coefficients are displayed on the backlit LCD, and are calculated from a user-programmable sled weight.
-
Product
DC Power Module, 8V, 12.5A, 100W
N6742B
Power Module
The Keysight N6742B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Safety Test Panel for Luminaire Fixture
-
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
6TL24 Combinational Base Test Platform
H71002400
Test Platform
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
Universal Test Fixture
CAM/GATE
-
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
Product
Boundary Scan Program Development Service
-
No need for test fixtures. Integrates product development, production test, and device programming in one system. Test and Programming data can be reused in Production. Fast test procedure development. Reduced inventory management. Eliminates or reduces ICT usage time. Pre-production testing can begin as soon as prototype is released.
-
Product
Remote Display Kit for Post.4d
postrd
-
remote display kit for post4d, not RoHS compliant (can be considered test equipment, not subject to RoHS). Connects to PC Engines post4d PCI POST card (will not work with post2b or post5a). 20 inch cable, place display in a more accessible location. Ideal for software development or test fixtures.
-
Product
PXI 5A Fault Insertion Switch 10-Channel
40-196-001
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
Air Data Adapter Test Panel
TA-241
-
AZ-241 Adapter Panel is designed to meet manufacturer's requirements. This panel will allow by the book testing of the air data computer when interfaced with the main air data test fixture. The Scott-T transformer is optional or can be customer supplied. Without the Scott-T your API can read the altimeter resolver directly.
-
Product
Calibration
-
General purpose calibration/diagnostic tool.Built in precision resistors.Simple manual contact/routing/resistor selection.4mm terminal posts on key device connections.In line mode to aid fixture wiring/DUT debugging.Comprehensive documentation including circuit schematics.Connecting cables.
-
Product
Vacuum Test Fixtures
Series 63
-
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
Product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
Test Fixture
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
Product
Clamshell Type Mechanical Fixtures
Series 10
-
Semco MT Series 10: An affordable solution for testing of printed circuit boards.
-
Product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
-
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine the multi-channel SA with the internal swept-signal generators. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
USB-C® – USB 2.0 C Receptacle to A Plug
AUT17032-CRAP
-
This fixture is designed for USB-C 2.0 Plug and USB-A products.
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 9,30 kg
-
Product
DC Power Module 0 To 5 V, 0 To 10 A, 50 W
N6731B
Power Module
The Keysight N6731B, a 50 W basic DC power module, provides programmable voltage and current, as well as measurement and protection features at a very economical price. Use this module to power the device under test or ATE system resources, such as fixture control.
-
Product
Military & Aerospace Solutions
-
Military and aerospace electronics spans a vast array of complex applications, including communications, vehicle control, radar, electronic warfare and countless others. Although the applications are widely varied, there are similarities in the requirements as well. Typically these electronic systems, whether COTS (Commercial Off- the-Shelf) or custom developed for the application, share similar requirements for ruggedness, reliability, and precision. Our customers don’t have room for error, mission critical hardware test systems must perform as designed. Circuit Check provides military and aerospace testing solutions for ITA’s, Self-Test Fixtures and Automated Test Systems that meet the stringent needs of this marketplace.
-
Product
Edge Connector Fixture
220EDGE
-
An edge connector fixture can be a low cost alternative to a bed of nails fixture. The most important features of this Edge Connector Tester is its portablility, ease of use, intuitive control functions, and durability in a production environment.
-
Product
Receivers
Series 32
-
Semco’s Series 32 Receivers are the optimal design for interfacing the GR 2270 style (VG) test fixtures. Featuring Semco’s patented CAM/TRAC® design, the Series 32 Receivers provide a locking system that assures consistent contact throughout the entire interface. With a full 5/8″ stroke, the Series 32 Receivers allow additional clearance for coax and custom block applications. They are available with or without vacuum ports. Models include: Bench Top, Slope, 19” Rack Mount, Dual 19 Rack Mount, and Dual Benchtop configurations.
-
Product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
RF Signal Generator
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Test Fixture
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
