-
Product
9050 - 50 Module, 2-Tier Solution
-
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
Product
Grips and Fixtures for Force Gauges
-
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Product
ITA, G12x, Front Mount, 18 Module
410104474
ITA
The G12x ITA can be used with all G12x Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
Product
Flexible Pitch GND Fixture Clamps
GF-A
-
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
Product
Functional Test Fixtures
Test Fixture
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
PCIe
SFF 8639 Gen4 (U.2)
-
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
Product
Small Footprint Flex 20 ATE
Flex 20
-
The Flex 20 is floor mounted but maintains a small footprint on the shop floor. A VPC S6 interface is normally used on this system allowing multiple test fixtures to be used with the system.
-
Product
Werklicht® Pro
-
*Intelligent laser projector, *Exact positional representation on assemblies in 3D *For attachments, holes, bolts and more *Stencils, fixtures and coordinate measuring machines are superfluous *Avoid mistakes before they arise. *Simplifies, streamlines and speeds up work steps *Over the entire process chain - from data preparation to quality assurance With Werklicht® Pro , the "digital template", you build an elegant bridge between CAD data and the real object.
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
CAN Interface
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
-
Product
Test Probes
-
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
Product
Temperature Probes
-
Lake Shore offers a variety of temperature sensors in packages that enable mounting in very tight areas. But for some applications (especially if the sensors have to be immersed in liquid), you need to do more to protect the sensor circuitry. For these applications, a cryogenic temperature probe is the optimum choice. Encased in one of these stainless steel thermowell fixtures, the sensor can perform as designed, is unaffected by high pressure, and is sealed to keep electrical components and wiring protected from fluids and other elements.
-
Product
Military & Aerospace Solutions
-
Military and aerospace electronics spans a vast array of complex applications, including communications, vehicle control, radar, electronic warfare and countless others. Although the applications are widely varied, there are similarities in the requirements as well. Typically these electronic systems, whether COTS (Commercial Off- the-Shelf) or custom developed for the application, share similar requirements for ruggedness, reliability, and precision. Our customers don’t have room for error, mission critical hardware test systems must perform as designed. Circuit Check provides military and aerospace testing solutions for ITA’s, Self-Test Fixtures and Automated Test Systems that meet the stringent needs of this marketplace.
-
Product
Custom Test Connectors and Sockets
-
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
Product
USB-C® – USB 2.0 Plug HS SQ Test Fixture
AUT17094
-
This product is designed for USB-C USB2.0 Receptacle Host Electrical Test.
-
Product
PXI-5651, 3.3 GHz RF Signal Generator
779670-01
Signal Generator
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Manual Probearm for HBM and Flex-Pitch Applications
TPA-GFM
-
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
Fiber End-face Interferometer
-
Anfkom International Co.,Limited
1.Automatic MeasurementSANA2 is equipped with the locking handle sensing unit to monitor the device locking status. To further simplify the testing process, the instrument can start the measurement once the device to be tested is fully locked. Operator can also click the button aside the locking handle to trigger the measurement.2.0~12° APC Angle Auto TuningBenefit with the unique fixture design, SANA2 can tune the APC angle precisely from 0°to 12°automatically, meeting any special requirement on APC angle setting.3.Simple and User Friendly Interfaces and Excellent 3D ImagesThe software of A 2 is simple and user friendly, you can change the language within the software. It provide many endface rebuild method such as 3D, 2D, plot to assist the engineers about the process. The test reports and data are generated automatically for analyzing and tracing.4.Auto Centering ImagesSANA2 has auto centering image function that can find the fiber and makes it to center automatically within one click.No mouse drag or hardware adjustment is needed.5.Cleave Angle Measurement
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Product
DC Resistance Tester
ZLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
Product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
Resistivity Cell
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
Product
Precision LCR Meter With Component Fixture And Limits Comparator
LCR400
-
0.1% basic measurement accuracyDual 5 digit high brightness displaysAutomatic component recognitionBuilt-in 4 terminal component fixtureLimits comparator with 8 Pass bins plus 2 Fail binsThree test frequencies, switchable biasRS232 interface standardOptional SMD tweezers, BNC connectors, Kelvin Clip test lead set, and PC logging software
-
Product
Medium Kelvin Clip Lead
16089B
Accessory Kit
Measure odd-shaped components that you cannot measure using conventional fixtures
-
Product
Reel to Reel Non-Contact OS Inspection System for TAB/COD/TCP/TBGA
TRV
-
*Most suitable mechanism for non-contact inspection*Sprochet-less transfer decreases products damage.*Easy operation by Fixture alignment mechanism*Equipped with Tracing Test function
-
Product
ATE Test Probes
-
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
Product
LCR Meter
SS10X Series
-
LCR Meters are basic passive component testing equipment, can be used in quality management department or production process for quality inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, electric valve, contactor, cable, wire, etc. This series LCR meter, offering different kind of testing fixtures, can improve testing precision and reduce the difference value of error code, being an economical and useful basic testing instrument.
-
Product
ICT/FCT-Fixtures (Large IF)
GenRad CK-2-228X
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Functional Test Fixtures
-
EMC Technologies designs and manufactures discretely wired and wireless functional test fixtures used for performance verification of PCBs and Electronic Assemblies. Commercial applications have included work in support of many industries including: satellite TV, computer servers, medical, networking, and telecommunication.
-
Product
CMP Mechanical Kits (120x138mm)
230197 – CMP-150-HP
-
The CMP Mechanical kits are an excellent option for manual tests of both low and high volumes. Now in a more rigid design with removable probe plate for easier maintenance. Integrated fixture down switch as an option. The kit is available in 4 standard sizes but can be adjusted to your demands.
