Parasitic Voltage
draw on battery when vehicle is off.
-
Product
LXI High Voltage Matrix 2-pole 200x2
60-310-202
Matrix Switch Module
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-905-HI
Multiplexer Module
The 65-231-905-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
High Voltage Tester
-
The High voltage tester for routine testing of MCBs combines a conventional high voltage tester with a specially designed robust fixture to hold 20 single pole MCBs at a time. The solution comes as a single trolley with easy-to-set test parameters with safety interlocks designed for user safety with respect to electric shock and mechanical fixturing. An advantage of the system is – it gives a high yield (20 MCBs are tested in about one minute) thus yielding user safety at a high value for money.
-
Product
LXI High Voltage Matrix - 750V 50x4 Matrix Plugin Module
65-218-111
Matrix Switch Module
This plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 750V without access to the chassis backplane.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-115-HI
Programmable Resistor Module
The 40-230-115-HI (PXI) and 42-230-115-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 925Ω with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Clamping Voltage Tester
MIG0603CLV2
-
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
Product
Voltage Controlled Amplifiers
-
Teledyne Microwave Solutions (TMS) offers a variety of high-performance voltage controlled amplifiers operating over a 5 to 2500 MHz range. These VCAmps feature an AGC range of 20.0 - 50.0 dB and Response Times from 3 – 25µs. TMS has a broad range of component products to meet your demanding needs.
-
Product
AC Voltage and Frequency Transducers
NMTU/F
-
The NMTU/F device is an AC voltage and frequency transducer with two independent analogous outputs. The A output measures AC voltage, the B output measures the frequency of input voltage. That´s why one single NMTU/F transducer is able to replace two customary transducers, thus making it possible to achieve significant savings in installation space.
-
Product
RF Voltage Probe
P-20 Series
-
The P-20A is a PASSIVE 10:1 RF VOLTAGE PROBE with a 50 Volt DC BLOCK built in. It has been designed to allow users of RF test equipment to use standard signal tracing techniques. The P-20A makes it possible to conveniently and accurately monitor or inject signals up to 3 GHz into RF circuits without significantly loading or detuning them.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-222-HI
Programmable Resistor Module
The 40-230-222-HI (PXI) and 42-230-222-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 1.81kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-136-HI
Programmable Resistor Module
The 40-230-136-HI (PXI) and 42-230-136-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 395kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Wide Range High Voltage Programmable DC Power Supply
N3600 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N3600 series is developed based on NGI's years of experience in testing for battery fluctuation simulation test, battery charger, high voltage diode, electrolytic capacitor, electromechanical control, ATE test system, etc. It is a high-voltage wide-range programmable DC power supply. According to different test environments in the fields of lab test, system integration test, and mass production line, NGI has made a number of optimization designs based on the international advanced technology. N3600 series is a market leader in similar products in terms of reliability, maintainability and safety.
-
Product
Standard Voltage 37 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
PXI 12 Channel High Voltage Multiplexer
40-320-001
Multiplexer Module
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
Differential Probe
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
-
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
Product
Electronic AC/DC Voltage Tester
ET60
-
The ET60 voltage tester requires no batteries as it measures AC/DC voltage up to 600V in electrical circuits, outlets, light fixtures and anywhere else AC/DC voltage testing is required.
-
Product
Voltage and Current Measuring Technology
-
HIGHVOLT Prüftechnik Dresden GmbH
Designed for the measurement of alternating current (AC), direct current (DC), lightning (LI) and switching (SI) impulse high voltages (HV) as well as AC and impulse high current (HC) according to IEC 60060, IEC 61083 and IEC 60052, available as indoor and outdoor design.
-
Product
PXI 16x SPST High Voltage Reed Relays
40-310-101
Reed Relay
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-310-HI
Programmable Resistor Module
The 40-230-310-HI (PXI) and 42-230-310-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-055-HI
Programmable Resistor Module
The 40-230-055-HI (PXI) and 42-230-055-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PC Controlled High Voltage Tester
Cablescan H23
-
The Cablescan H23 combines low-voltage solid-state technology with high-voltage relay technology ¾ solid-state devices for testing continuities and components at low voltage; relays for testing high-resistance isolation and high-current continuity.
-
Product
Standard Voltage 50 Pin D-Type Connectors for Pickering
-
The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 50-pin D-type connector.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-031-HI
Programmable Resistor Module
The 40-230-031-HI (PXI) and 42-230-031-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Programmable Voltage Reference Plug-In
ProDAQ 3202
-
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-150-HI
Programmable Resistor Module
The 40-230-150-HI (PXI) and 42-230-150-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Low Voltage Switching Regulators
-
Renesas' comprehensive portfolio of low voltage, synchronous buck integrated FET switching regulators offer a compact solution size with outstanding performance.
-
Product
AC / DC Voltage And DC Polarity Tester
1861
-
Peaceful Thriving Enterprise Co Ltd
*With cETL Approval.*Built-in LED and neon lamp indicator.*Neon lamp for 120V-230V-400V AC.*LED Display for 12V-50V and polarity.*Long lead connects tester body and probe.
-
Product
Eight-channel USB Voltage and Thermocouple DAQ
Model DI-2008
-
Includes DI-2008 instrument, WinDaq software, calibration certificate, terminal screwdriver, and USB cable (6-feet). Eight differential and isolated analog input channels. Seven bi-directional digital input ports, including: Counter input for totalizing applications, Rate input for frequency/flow/rpm applications. ChannelStretch™ channel expansion to 128 analog and 112 digital channels. Programmable voltage and thermocouple measurements per channel. 10 mV to 50 V programmable range per channel in 12 steps.
-
Product
PXI Quad 6:1 High Voltage Power MUX
40-331-003
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
