Coaxial Matrix
route radio frequency signals through a a grid array.
-
Product
PXI 8-Slot BRIC Matrix, 77x16 2-Pole (7 sub-cards)
40-562B-122-77X16
Matrix Switch Module
The 40-562B-122-77X16 is a high density BRIC8 matrix module with a size of 77x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, MCX
42-837A-102
Matrix Switch Module
The 40-837A-102 (PXI) and 42-837A-102 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
PXI 12-Slot BRIC Matrix, 512x8 1-Pole (8 sub-cards)
40-558-121-512X8
Matrix Switch Module
The 40-558-121-512x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI BRIC4 1Resource Distributor, 3Bus Matrix
40-569-013
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
SMA Male to SMA Male Cable, 50 Ohm, 12.7 cm
763443-01
Coaxial Cable
The SMA-SMA Coaxial Cable, sometimes referred to as SMA100, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths.
-
Product
LXI Low Thermal EMF Matrix 1-pole 14x33
60-510-004
Matrix Switch Module
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset. The 60-510 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
Product
PXI Single 2x2 RF Matrix SMB 75 Ohm
40-837-001
Matrix Switch Module
The 40-837-001 is a 75Ω 2x2 RF matrix with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-837 modules.
-
Product
PXI 4-Slot BRIC Matrix, 220x4 1-Pole (5 sub-cards)
40-562B-021-220X4
Matrix Switch Module
The 40-562B-021-220X4 is a high density BRIC4 matrix module with a size of 220x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
Matrix Switch Module
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
PXI 8 Slot BRIC 230x8 1-Pole Dual Analog Bus (5 sub-cards)
40-560A-121-230X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4 Slot BRIC 24x16 2A 1-Pole Matrix
40-598-001
Matrix Switch Module
The 40-598 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-598 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-34
Relay Matrix Module
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 160x8, 1-Pole (5 sub-cards)
40-563B-121-160X8
Matrix Switch Module
The 40-563B-121-160x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
PXI 2 Slot BRIC 132x4 1-Pole (3 sub-cards)
40-562A-221-132X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
Keysight Dual 4x8 Armature Matrix for 34980A
34931A
Matrix Switch Module
The Keysight 34931A module for the 34980A Multifunction Switch/Measure Unit gives you the most flexible connection path between your device under test and your test equipment, allowing different instruments to be connected to multiple points on your device under test at the same time. Dual 4x8, 8x8, or 4x16 configurations 64 2-wire cross-points Connections to the internal DMM Expandable via four 2-wire analog buses Relay counter Latching armature relays 300 V, 1 A switch; 2 A carry current
-
Product
PXI Single 33x8 Matrix 2-Pole 1A
40-581-002
Matrix Switch Module
The Worlds highest density 2-pole single slot 3U PXI Matrix Module, the 40-581has 264 crosspoints configured as a 2-pole 33x8 matrix. The use of high density electromechanical relays means that the 40-581 is a low cost high density matrix solution with current handling up to 1 Amp. The 40-581 module is suitable for matrix applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based matrices do not have sufficient power handling capability.
-
Product
LXI 1GHz 75ohm 24x16 Matrix
60-730-002
Matrix Switch Module
The 60-730 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-730 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
Product
LXI High Density 64x64 2 Matrix With BIRST
60-552-027
Matrix Switch Module
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI/PXIe Switched Guard Matrix, 16x4
42-590-101
Matrix Switch Module
The 40-590-101 (PXI) and 42-590-101 (PXIe) are modules that provide a switched guard 16x4 matrix solution with up to 1012 Ω channel to channel and channel-to-ground isolation.
-
Product
PCI Single 22 X 8 Matrix 1 Pole Screened
50-512-021-S
Matrix Switch Module
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
PXI 8 Slot BRIC 105x16 2-pole (7 sub-cards)
40-561A-122-105X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 10x4 Matrix 2A 1 Pole
40-545-001
Matrix Switch Module
The 40-545 series of modules are high density power switching matrices. Typicalapplications include power routing in Functional ATE systems, specifically automotiveelectronics, for example testing of Engine Management Units.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 525x4, 7 Sub-cards
40-568A-107
Matrix Switch Module
The 40-568A-107 is a PXI 1-pole 525x4 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-568A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 2-Slot BRIC 24x8 Matrix, 2A 2-Pole (1 sub card)
40-565A-202-24X8
Matrix Switch Module
The 40-565A PXI Matrix BRIC is a range of high-density matrix modules able to switch up to 2 Amps at 150VDC/100VAC They are available in 2, 4 or 8 slot PXI sizes to suit most high-performance PXI Matrix requirements and constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXIe 64x4 High Density Matrix Module, 1-Pole, 2A, 60W
42-585A-001
Matrix Switch Module
Our model 40-585A, along with the following models 40-584A, 40-586B and 40-587A are high-density single pole PXI matrices each with 256 crosspoints. All models use gold-plated contact electromechanical relays. This module is also available in PXIe format (42-585A-001).
-
Product
PXI Dual 12x4 Matrix, 2 Pole Switching
40-511-022
Matrix Switch Module
The 40-510 series of matrix modules feature a wide range of selectable switchingconfigurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signalrouting in ATE and data acquisition systems.Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Larger matrices may be constructedby Daisy Chaining the common signals from multiple PXI modules.
-
Product
PXI 12-Slot BRIC Matrix, 396x8 1-Pole (18 sub-cards)
40-562B-321-396X8
Matrix Switch Module
The 40-562B-321-396X8 is a high density BRIC12 matrix module with a size of 396x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Solid State 8x2 Matrix, 30 Amp
40-555A-011
Matrix Switch Module
The 40-555A-011 is a high current 8x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI 12-Slot BRIC Matrix, 396x8 2-Pole (18 sub-cards)
40-562B-322-396X8
Matrix Switch Module
The 40-562B-322-396X8 is a high density BRIC12 matrix module with a size of 396x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC 176x4 2-Pole (4 sub-cards)
40-562A-022-176X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
