RF Matrices
route radio frequency signals through a a grid array.
-
Product
High Performance/Software Controllable RF Multicouplers
-
1U High Performance Rack Mount Broadband Multicouplers, with configurations up to 1×8 or switchable 2×4 configurations. Features include High Output/Output Isolation and Software Controllable power level and amplitude balance.
-
Product
2 X 1 RF Switch
MX 1×2 RF
-
Auto detect 2×1 RF switch, used for simple automated switching or redundancy of the RF signal path.
-
Product
SP16T RF Pin Diode Switches To 10 GHz
-
Pulsar Microwave's 16-way switches cover 500 MHz to 10 GHz in single pole, 16-throw configuration. Maximum input power is 200 mW and switching time is 100 ns. SMA female connectors are standard. A 15-pin D-SUB male connector makes the internal connections to the power, ground and logic circuitry. Switching control is TTL with the option of line drivers and decoders.
-
Product
EMC & RF Solutions
-
Microwave Absorbing Material Characterization System that measures the signal loss through a material sample in a frequency range of 5 15GHz (with the option of extension to lower frequencies).
-
Product
RF Benchtop / EMC Amplifier
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
RF Coaxial Connectors
-
Radiall is proud to offer the widest range of RF coaxial connectors in the industry. We offer over 13,000 part numbers and 55 product series including AEP® and Mil QPL connectors. Radiall started by manufacturing coaxial cables and connectors; now, more than 60 years later, these precision-made components are still a primary focus of our business. We design and manufacture RF coaxial connectors for a wide variety of industries. Our offerings include coax connectors that are waterproof, high frequency, snap-on, non-magnetic and more. We will also design custom connectors for your specific application.
-
Product
RF Shielded Test Enclosure, Ideal for tall RF devices
JRE 3036
-
For testing tall devices, the JRE 3036 is ideal! Large enough to fit entire computer systems inside, as well as their associated components, everything will be securely isolated from the outside world. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
RF & Microwave Test Cables
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
VNA Test Cables and microwave cable assemblies (RF Coax cable assemblies) must have a high degree of mechanical flexibility in combination with constant electrical stabilities. Such cables are usually used in laboratories for high-frequency measuring applications and test stations, as well as in the areas of telecommunications, automotive, medicine, industry, consumer electronics and aerospace for signal transmission and other applications.
-
-
Product
LXI Low-Frequency Matrices
-
Our LXI low-frequency matrices provide complete flexibility for connecting test equipment and the unit under test (UUT)together and are compliant with LXI Standard 1.4
-
Product
FieldFox C Handheld RF Analyzer, 4 GHz
N9913C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
RF Systems
-
With our detailed, end-to-end knowledge of beam generation systems and the way platforms operate in the field, we deliver state-of-the-art radio-frequency and x-ray systems. These integrated and effective systems are built with optimised components and interfaces to achieve the performance, reliability and ease-of-use expected by platform designers, manufacturers and end-users.
-
Product
Microwave& RF Signal Generator
-
Berkeley Nucleonics Corporation
A low-noise, fast-switching, high power and offers wide frequency ranges.
-
Product
Polyurethane Jacket RF Cable Assemblies
-
For applications where space is limited and minimizing transferred mechanical stress on the interface connection is a must...The polyurethane jacketed versions of our already proven cable assemblies deliver new engineering options to standard FEP jacketed cables.Polyurethane offers greater memory retention than a similar size cable jacketed with FEP. This feature offers the benefit of minimizing stress and torque applied to interface connections, such as those on a circuit board.It also allows cable to better maintain position in an installation where the "spring back" of an FEP jacketed cable could be problematic.Additionally, a polyurethane jacket offers improved abrasion resistance over an FEP jacket.
-
Product
Standard RF Fixture
-
The standard RF fixture supports both pulsed and non-pulsed operation. It employs SMA input/output connections. For RF output powers over 10W, an N-type connector may be used to replaces the SMA connector because of its power-handling capability.
-
Product
Concurrent Alternative RF & GNSS Signal Simulation
SimAltNav Replay
-
Non-GNSS sources of RF (radio frequency) are of interest in GPS-degraded or contested signal environments, with interest focused on LEO (low earth orbit) constellations. These systems offer high receiver signal power (relative to GNSS) and a secure & resilient link to augment GNSS.
-
Product
PXI 8x9 RF Matrix 500MHz 50 SMB
40-725-511
Matrix Switch Module
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
Product
RF Switching PXI Card
GX6062
Switch Module
The GX6062 is a high-density 6U PXI RF switching card that provides 200MHz bandwidth and multiple switching configurations. The GX6062 has 12 groups of 1 x 4 differential, non-terminated RF multiplexers. The 12 groups can be used to create multiple configurations including: 6 x 1:9, 3 x 1:19, 2 x 1:29, 1 x 1:59, and more. The GX6062 switching card plugs directly into any 6U PXI chassis.
-
Product
Microwave Switch RF Switch - 26.5G AXIe
RF Switch-26.5G AXIe Module
-
The RF Switch-26.5G AXIe module is designed to work as part of information measuring systems as a radio frequency signal switch (one input to six outputs for each of the eight input lines).
-
Product
RF Amplifiers up to 6000 MHz
-
Includes RF and microwave amplifiers covering the band from 500Mhz to 6000Mhz in a single module with either GaN or GaAs devices. Custom and standard power amplifiers available with high linearity, low noise figure, and very low error vector magnitude (EVM). Our rack systems and select modules include Automatic Gain Control (AGC), Automatic Level Control (ALC), and peak/pulse/average detection useful in OTA, MIMO, and CTIA testing.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
PXI Hex SPDT RF Switch SMB 75 Ohm
40-830-006
RF Switch
The 40-830-006 is a 75Ω RF Switch 6 separate SPDT relays in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI-5670 , 2.7 GHz RF Vector Signal Generators
778768-04
Vector Signal Generator
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
Product
PXI Triple SPDT RF Switch 3GHz 50 SMB
40-870-003
Switch Module
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
Product
Personal RF Detection Meters, Low Frequency
-
Personal RF Detection Meters, Low Frequency by Sensory Perspective Ltd.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 50Ω, SMB
42-870A-003
Switch Module
The 40-870A-003 (PXI) and 42-870A-003 (PXIe) are 50Ω RF switches with 3 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
RF Safety Monitoring
fieldSENSE 2.0
-
LBA's FieldSense 2.0 personal RF safety monitors are an effective and economical means to monitor the strength of electromagnetic (RF) fields from wireless cell phone towers, microwave ovens, television stations, and other common workplace RF sources between 50 and 6000 MHz, E-field and H-field (sensed as a plane wave). The Personal RF Monitor is essential RF safety equipment in complying with FCC, OSHA, Canadian and other workplace rf safety requirements.
-
Product
PXI Triple SPDT RF Switch SMB 75 Ohm
40-830-003
Switch Module
The 40-830-003 is a 75Ω RF Switch with 3 separate SPDT relays in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
