-
product
Digital Multimeter
380
This digital multimeter has the compact design and the functions you need for overall convenience. Its capabilities are equal to many higher priced multimeters. Comes with test leads, protective holster, instructions and installed 9 volt battery.
-
product
Digital Input Board
VME-1182A
A multifunctional intelligent controller allows COS, SOE, pulse accumulation, debounce times and time tagging control on a per-channel basis.
-
product
High Precision Digital 1A Micro-Ohmmeter
DRM-1A™
The DRM-1A™ is a lightweight and portable micro-ohmmeter designed to measure very low resistances from 1 μΩ to 200 Ω. It is the most accurate in its category.
-
product
AC/DC Digital Clamp Meter
Up to 400A AC/DC.Conductor dia. : Φ19mm max.True RMS.Peak Hold.Simple switch operation for easy of use.
-
-
product
Dual Input Digital Handheld Oscilloscope
SDM 760
Dual Input Digital Oscilloscope ; 20MHz. Dual Input Digital Multimeter ; AC/DC Volt, Frequency. Interface ; RS-232 Optically isolated. Operating time ; 2 hours with backlight. Charging time ; 12 hours
-
product
Digital to Analog Converter
20-bit digital-to-analog (D/A) converter offering 20-bit monotonic performance over the specified temperature range. It utilizes delta-sigma technology to achieve inherently linear performance in a small package at very low power. The resolution of the device can be programmed to 20 bits for Full-Scale, settling to 0.003% within 15ms typical, or 16 bits for Full-Scale, settling to 0.012% within 2ms max. The output range is two times the external reference voltage. On-chip calibration circuitry dramatically reduces low offset and gain errors.
-
product
Digital Load Cell Simulator
Model EL41
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
product
Multifunction Digital Tester
*Contact ACV test*Non-contact ACV test*Continuity check*DC Voltage / Polarity check
-
product
Digital Dailysate Meter
Digital Dialysate Meter™ D4 & D6
The DIGITAL DIALYSATE METER is specifically designed to test both acetate and bicarbonate dialysate quality. Measure Conductivity, pH and Temperature to ensure proper mixing during dialysate preparation and as a final check of dialysate quality before hemodialysis treatment. There are no strips or reagents that expire or subjective interpretation of results. Internal sensors require the user to place the sample in the instrument, preventing contamination of dialysate by the measurement device.
-
product
M2730 DIGITAL PORTABLE FLOW CALIBRATOR
M2730 is the new digital portable calibrator of ForTest® M series. Enclosed in a container of anodized aluminium with shatterproof plexiglass front, we find a completely new circuit board and a mass flow meter sensor, for direct measurement of leaks. Coupled to the micrometer nozzle supplied, they are designed to simulate the desired leakage, facilitating the procedure for programming and verification of leak test instruments.
-
product
Digital Step Attenuators To 18 GHz
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
product
Digital Input Scanner
IM2030
Available with us is a digital input scanner that shows the status of digital / potential free inputs connected to the unit. The units are available with 8/16/32 inputs and the names for each input can be configured for easy identification. MODBUS interface is provided to transmit the current status of the inputs to pc.
-
product
Portable Digital Tesla Meter
HT20
This instrument is convenient for operator to measure magneticinduction of DC magnetic field accurately. It is characterized by its wide range, clear display of LCD, and indefectible structure of sensor.A piece of 9V dry battery, which acts as its power supply, can servefor 4 hours continuously. Meanwhile, regulated power supply (enclosed) is available to 220VAC.
-
product
64 Input USB Modular Digital I/O
U2652A
The Keysight U2652A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
product
PCI Digital I/O and Relay Driver Cards
a 32-channel Digital I/O card with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel.
-
product
PXIe-6569, PXI FlexRIO Digital I/O Module
787283-01
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
4 4/5 DIGITAL MULTIMETER
IBL-608
International Biological Laboratories
This 4-4/5 Digits Digital Multimeter with 50000 Counts LCD Display is ideal for professionals for whom there is no compromise to accuracy. This is a complete Digital Multimeter with facility of analytical analysis via the RS-232 PC interface facility with which all the data can be down loaded to the PC for analysis.
-
product
Mini Digital Sound Level Meter
PSPL01
Frequency Range: 31.5 Hz-8 KHzMeasuring Level Range: 40 to 130 dBAccuracy: +/- 3.5dB @ 1 kHz, 94dB (Under Reference Conditions)1/2" Electret Condenser MicrophoneNewly Designed HousingC-type Frequency WeightingHigh Performance & Auto LCD Backlight50 hrs. Battery LifeAuto Power Off (15 Minutes Inactivity)Sold as : Unit
-
product
Digital Contact Thermometers
Digital thermometer can accommodate a wide variety of K-type thermocouple tips that are suited for many types industrial and commercial temperature measurement applications such as Kilns, Ovens, Furnaces, Heat Treating, Ceramics, Pottery, Molten Metal, Crucible and many others
-
product
Digital Panel Meter
MW(Q)-5A
Mx-5A meter to provide power (Watt or Active Power or Re-active Power or Power Factor), high-precision measurement, display and remote communication capabilities.Additional purchase: 1 group of relay outputs, 1 analog output, an RS485 communication output (the Modbus RTU Mode) interface, so that can be installed in power management, remote input and output, alarm and variety of remote communication control the use of needs.120mm (D) is ideal for assembling in panels with limited penetration depth.
-
-
product
Digital Height Gauges
Digital Height Gauges is a measuring device used to determine the height of objects and mark items. Another option is to measure the height of the object using the bottom.
-
product
Digital Multimeters
This multimeter is most suitable for use on production lines or lab, R & D, maintenance and repairing work.
-
product
128 Channel Digital I/O Modular PXI Card
GX5733 Series
The GX5733 is a 3U modular digital I/O card that offers up to 128 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5733 offers the highest channel density and flexibility in the industry for a single-slot, 3U PXI plug-in board. 96 channels support TTL levels and an additional 32 I/O channels can be customized by installing one of Marvin Test Solutions' GX57xx series I/O modules. Alternatively, the remaining port can be configured to support 32 TTL channels.
-
product
Digital-Phase-Lock-Loop
The Quartzlock A6-CPS is a board level product designed for synchronising two stable oscillators. A typical example is the locking of a low phase noise OCXO to a rubidium frequency standard. The product uses a digital implementation of a standard phase lock loop.
-
product
15-CH Isolated Digital Output Module
ND-6056
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Digital Motorized BRINELL Hardness Tester
900-355
Load Cell driven system provides precise control of test force application Direct digital reading Engineered to obtain highly sensitive and accurate readings Perfect for laboratories, workshops, tool rooms, inspection labs, etc. Measuring Range: 8-650HBW
-
product
Industry Pack Carriers and Digital I/O
CPCI-2IPC-6U
The CPCI-2IPC-6U module provides a high performanceflexible I/O scheme, that supports industry standard IndustryPacksÔ. For application requiring high performance, highdensity I/O or unique combinations, the CPCI-2IPC-6U is theperfect solution. The Local DSP’s can be used to simplymove data to and from the CPCI bus or provide localprocessing functions such as local PID controls, FFT’s, digitalfiltering, etc.
