Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
General Purpose Basic Carrier Demodulator
CD15
-
The CD15 Sine Wave Carrier Demodulator operates with variable reluctance transducers to provide a DC output signal for dynamics as well as steady state measurements. A 5kHz sine wave excitation is applied to the two inductance ratio arms of the transducer and the resulting output is demodulated and amplified using the latest integrated circuit techniques. The DC output is obtained from an active filter circuit and gives a uniform response from steady state to 1000 Hz. The low impedance sine wave excitation allows operation with the transducer located over 1,000 feet from the CD15.
-
Product
Remote & Large Digit Displays
-
Remote and Large Digit Displays, as defined in this web page, are numeric displays that are driven by a serial signal from a computer, programmable controller, or other instrument. Digit heights can range from 0.56" (14.2 mm) to 11.0" (280 mm). Laureate remote displays, with a digit height of 0.56", are similar to a digital panel meter or counter in appearance.
-
Product
RTM Analog Signal Conditioning Board
MS 3633I
-
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 8-Channel, 4-Pole
40-614D-008
-
The 40-614D-008 (PXI) and 42-614D-008 (PXIe) 4-bank, 8-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI-8512, 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-02
-
2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
LXI Microwave Multiplexer, SP4T, 3-Bank, 26.5GHz, 50Ω, SMA, Terminated
60-803-303
-
High performance RF multiplexer suitable for switching microwave signals up to 26.5GHz with automatic termination of unused signals
-
Product
L-Band Matrix Switches
-
Quintech Electronics and Communications Inc.
L-Band RF Signal Management.
-
Product
NI-9862, CAN Interface Module
781639-01
-
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
Spectrum Analyzers
-
GAOTek spectrum analyzers can monitor the levels of spurious signals, such as intermodulation products, noise, harmonics and other signals, to see whether they meet the required levels by displaying the frequency of the signals on the horizontal scale and the amplitude of signals on the vertical scale. GAOTek sells these spectrum analyzers to the United States, Canada and Globally.
-
Product
FPGA Card
VP780
-
The VP780 is a high-performance Virtex-7 VPX card with advanced digital signal processing capabilities. The design has been optimized for the implementation of complex FPGA algorithms with high throughput requirements.
-
Product
1465 Series Signal Generator (100kHz – 67GHz)
1465
-
1465 series microwave signal generators, with the frequency range of 100kHz – 67GHz, is provided with high purity spectrum and high output power. It can meet the high-end requirements of electromagnetic signal tests. S1465 series are mainly used in the radar performance evaluation, high-performance receiver test and components parameter test etc., and applicable to aviation, aerospace, radar, communication and navigation equipment etc.
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Double Monochromators/Spectrographs
Omni-λxxxD
-
Omni-λxxxD series Double Monochromators/SpectrographsThe Double Monochromators/Spectrographs include two 300 mm focus monochromators( or 500 mm, 750 mm focus) which are with fine alignment. Double Monochromator has the dispersion subtraction mode and dispersion sum mode. Using dispersion sum mode, the double monochromator / spectrograph spectral resolution can be doubled, suitable for high resolution measurement. Using dispersion subtraction mode, the double monochromator / spectrograph stray light can be reduced effectively, suitable for weaker signal detection, such as Raman spectral measurement.
-
Product
Shaft Speed Sensors - Magnetoresistive
1102 / 932 / 933 XP
-
Features• Square-wave pulse frequency output, NPN open-collector• Zero speed operation with no signal loss• 5-24 VDC powered• 1/2" NPT conduit port (933 XP)• Non-contact, large gap distance sensing• Simple to install and set up• Works with Electro-Sensors magnetic pulser discs / wraps• 1102 – non-threaded stainless steel
-
Product
Impedance Matching Pads
-
Impedance matching pads from BroadWave eliminate impedance discontinuity (mismatches) without introducing reflection to the circuit. Custom units are available in a variety of impedance and connector types from DC to 4 GHz. BroadWave Technologies impedance matching pads preserve signal integrity by matching virtually any transmission line.
-
Product
PXI-5402, 14/16-Bit, 20/40 MHz Arbitrary Function Generator
779655-01
-
20 MHz Bandwidth, 14-Bit PXI Waveform Generator—The PXI‑5402 is a 20 MHz function generator capable of generating standard functions including sine, square, triangle, and ramp as well as other signals like psuedorandom noise and DC signals. This function generator can generate signals from -5 V to +5 V and uses direct digital synthesis (DDS) to precisely generate waveforms.
-
Product
GPS Antenna Signal Splitter 3 Way, SMA Jack, Passive, L1 & L2, 50 Ohm
GPS310
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
-
Product
2GHz programmable frequency dividerValon
3010a
-
The Valon 3010a accepts a wide range of input frequencies and provides three independent, user-selectable, divided outputs. The 3010a is useful for extending the low-frequency range of any signal source down to 5MHz as a 50Ω output or down to 0Hz as a TTL output.
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
-
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
7 Spade Pin Circuit Tester / Maintenance Kit
#8028
-
Innovative Products of America
Test, clean and restore 7 spade pin connections.The tester will verify that the tow vehicle is sending proper signal to the connector, while accompanying cleaning tools will remove corrosion, and verify proper pin size on both male and female truck/trailer plugs. For use with 7 spade connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardPatentedKit Includes: #7893: 7 Spade Pin Circuit Tester, #8023: Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
Product
Monics® SatID®
-
Kratos Defense & Security Solutions, Inc.
Kratos’ leading RF interference geolocation product, satID® provides an accurate, fast, all-in-one solution for locating and identifying sources of interference, including VSAT/TDMA terminals. With the capability to geolocate within 5 km of the interfering signal, satID is the most accurate geolocation product available today.
-
Product
High-Voltage Test Hood with Integrated Hipot
LX-HVE900IS
-
Large test room with a hood made of sturdy, highly insulating and transparent plastic, which guarantees a clear view of the test item and the signal lamp during the test. The system is operated on the test device. Alternatively, test sequences stored on an integrated computer can be started automatically by closing the hood. The test sequence can be fully followed on the monitor.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
PXI Ultra High Density 64x2 1-Pole Matrix
40-533B-031
-
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
Protocol Intelligent Pressure Transmitter
HR3288Hart
-
HighReach Measuring & Controlling System Co.,Ltd
The HR3288 HART protocol intelligent pressure transmitter is a high-precision, high-stability, multi-parameter, 4-position, half-LCD display intelligent pressure measurement product that complies with the HART protocol. Users can use the HART communicator to manage, adjust Or monitor process variables for HART instruments running in the process, or use the buttons for on-site configuration, which is easy to operate.This product adopts the latest application results of digital technology in the field of sensor manufacturing, combined with the most advanced pressure transmitter design and manufacturing technology, precision digital temperature compensation and nonlinear correction technology, safe and reliable explosion-proof structure design and standardized signal output , precision high, wide range coverage, suitable for places where precise measurement of fluid pressure is required.
-
Product
PID Controller
ZET 7190-R
-
ZET 7190-R — PID controller on CAN bus. It is used in automated systems for control signal forming.
-
Product
Dual 16x2 1-Pole High-Density PXI Matrix Module
40-520-501
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Smart GPIB Serial Interface Board
Model 4806
-
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
Product
Control Units
-
For integration into a larger system or for automated measurements, the gain control unit for automated systems lets you control the settings of the intensifier attachment. The control unit uses standard TTL and analog signals for communication, allowing the user to switch the intensifier on or off, alter the gain and the anode current limit of the image intensifier without the need of software integration.
-
Product
VLF Electromagnetics
-
VLF surveying relies on radio signals that are broadcast from navigation stations around the world. The principle is that these signals are deflected in certain ways when they pass through conductive ore or water-filled vertical-to-sub-vertial fractures in the earth. By monitoring these deflections, the position and, potentially, size of the target can be determined.
