Mixed Signal
Integrated circuit that handles both analog and digital signals.
See Also: Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, Mixed Signal Testers, MIxed Signal Test Systems
-
Product
Compact Multiformat Signal Analyzer
CVM-306-3GB
-
The Videotek® CVM-306 multiformat signal analyzer boasts integrated video and audio signal monitoring in an affordable, compact package. With a robust feature set and space-saving design, the CVM-306 allows even the most modest installation to benefit from high-end monitoring and a professional look.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
Signal Contact (Receiver)
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCu/PhBrzContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAvg Mating Force(lbs) 0.24
-
Product
Signal Lab
-
Quick-start features for Bluetooth, DECT, GSM, NADC, PDC, PHS, TETRA, WCDMA 3GPP, Worldspace, TFTS. Graphical representation for vector diagram, signal spectrum, and I/Q dependence on time
-
Product
E-Band Signal Analysis Reference Solution
Reference Module
The E-band signal analysis reference solution provides an effective measurement solution for today’s wideband signals as well as emerging communications standards. With the M1971E waveguide harmonic mixer, which provides a 55 to 90 GHz input; Keysight oscilloscopes, which provide excellent signal integrity; and the powerful 89600 VSA software, you have a high-quality wideband measurement solution. A simple user interface also provides integrated mixer setup, correction and LO optimization, allowing for accurate measurements.
-
Product
Amplifiers & Signal Processors
-
Power for Core Technology Group Signal Chain ProductsFlexible bi-polar voltage converter using low cost connectorsDriving multiple devicesIndustrial +/- 10 volt power source
-
Product
Signal Acquisition
277
-
The Model 277 is designed around the Texas Instruments ADS42LB69 16-bit ADC. The 250 MHz sample clock is supplied by either the on-board frequency synthesizer or an external source. The frequency synthesizer can be phase locked to the local 10 MHz TCXO or an external reference can be used to achieve system-wide phase coherence.
-
Product
6 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 6 Ports
GPS612
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Signal Conditioning
-
Sensors that are used to collect the data from the environment often don’t produce signal of characteristics optimal for an analog to digital converter (ADC) to translate to digital data. Additionally, these signals can be subject to electromagnetic interference (EMI) that introduces noise, having a negative impact on the reliability of the data. To make this analog input readable for the processing unit and dependable enough to give the desired quality of data the signal has to undergo a process of signal conditioning.
-
Product
Single and Dual Core Digital Signal Processor
SI-C665xDSP
-
The SI-C665xDSP from Sheldon Instruments is a C programmable Digital Signal Processor (DSP) card designed for low power environments that require intensive computing in a cost sensitive solution.
-
Product
Cellular Signal Analysers
SNYPER Family
-
2G, 3G and 4G LTE cellular signal analyser range - including Spectrum 'livescan'. The SNYPER is a sophisticated yet easy to use range of cellular signal analyser comprising 2G and 3G versions with LTE family Now available.
-
Product
System of High-Speed Synchronous Registration of Analog, Digital, and Video Signals
-
The system uses a high-performance NI CompactRIO controller to simultaneously register 24 analog signals, receive an accurate digital pulse from GPS and synchronize measurements.The video signal is recorded using a high-speed camera connected to an NI PCIe-1433 frame grabber. The information received from the camera and the recording device is transmitted to a server built on the basis of an industrial computer, which writes data to an external 12-disk RAID array. The stream of recorded data in the system can reach 600 MB per second.
-
Product
Signal Conditioners
-
SPECTEC Innovative Sensor Solutions
SPECTEC's frequency to current and frequency to voltage converters for passive and active magnetic speed sensors and all digital speed sensors fit in a variety of explosion-proof elbow enclosures or can be DIN rail mounted via special adapters. These signal conditioners change the sinusoidal input to a linear current or voltage output respectively. The 4-20 mA and 10-50 mA signal converter has many applications in the flow industry. The frequency to voltage converters provides either a 0 to 5 V (TTL) or 0 to 10 V output.
-
Product
Offline Signal Processing & Analysis Software
Signal Processing - DX
-
APEX Turbine Testing Technologies
DX is an easy to use, graphical, signal processing environment that simplifies analysis and reporting of dynamic data. DX includes everything needed to process data for a variety of applications and industries in a very intuitive, drag-and-drop user interface. Generate fully-interactive engineering plots from one or more tests and create reports in just a few mouse clicks.
-
Product
DIGITAL TV SIGNAL ANALYZER
1702/1703
-
The optimal signal analyzers to test and measure both analog/digital signals. Especially, these models give users the capacity to measure 'C/N' very easily and correctly, which are very important measurement factors for the TV broadcasting signal.
-
Product
2 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 2 Ports
GPS212
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
Signal Conditioners
SC-7400
-
The SC-7400 handles a variety of temperature and process inputs and offers combinations of analog and relay contact outputs. All parameters - such as input and output range, set-points, deadband and burnout - are customer-selectable via software.
-
Product
Talon 26.5 GHz Sentinel Intelligent Signal Scanning Rackmount Recorder
Talon RTR 2654
-
- Search and capture system using Pentek's Sentinel™ Intelligent Signal Scanner- Captures RF signals from 800 MHz to 26.5 GHz- Capture and scan bandwidths up to 500 MHz- Selectable threshold triggered or manual record modes- 12-bit A/Ds with 57.5 dB SNR & 72 dB SFDR- Built-in DDC with selectable decimations of 4, 8 and 16- 4U chassis with front panel removable SSDs- Storage capabilities to 245 TB- RAID levels of 0, 5, and 6- Windows® workstation with Intel Core™ i7 processor- SystemFlow® GUI with virtual Oscilloscope, Spectrum Analyzer and Spectrogram displays
-
Product
PXI Fault Insertion / Signal Insertion Switch Modules
Switch Module
Pickering's PXI Fault Insertion / Signal Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect all of which can simulate connectivity problems in the system. Two switching topologies are available: *Single signal paths with series switches and switches to connect to one or more fault buses*Pairs of signals with series switches, shorting switches between the signal pairs and switches to connect either signal to an external fault input.
-
Product
CW Test Transmitters / Signal Generators
-
The WTX CW test transmitter family is particularly designed for field applications such as Inbuilding site modeling (model calibration), DAS injection / testing, walk-testing as well as outdoor path model tuning- thanks to its broad range of optional power amplifiers.
-
Product
IEPE Signal Conditioning Amplifiers
-
Although IEPE (Integrated Electronics Piezoelectric) sensors is not a new technology there are a wide variety of applications where the measurement instrumentation is not configured with IEPE signal conditioning built in. In these situations it is necessary for the IEPE supply to be provided by an external source. Usually this type of instrument will also provide th user with the option to add gain to the signal being conditioned. The Kemo range of IEPE signal conditioning instruments can be used as stand alone conditioners/amplifiers are many of them can also be integrated with filters.
-
Product
Signal, Module, Receiver, TriPaddle, 90 Series, 96 Position
510104136
Receiver Module
Primary mating module 510108126. (May mate with other ITA modules, as well.)
-
Product
Signal Conditioner in DIN Rail Housing
Series IMA2
-
INELTA Sensorsysteme GmbH & Co. KG
For LVDT Displacement Sensors, DMS Force Sensors and potentiometric Sensors
-
Product
4 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 4 Ports
GPS402
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Saluki LSG022 Analog Signal Generator (Modular)
-
Saluki LSG022 analog signal generator offers 100kHz to 22GHz frequency coverage with 10ms frequency switching speed. It can be used independently or combined with the chassis to form a test system.Saluki LSG series signal source is the cost-effective choice when you need to balance budget and performance. It provides the signals you will need for radar performance evaluation, high-performance receiver test and components parameter test etc..
-
Product
QAM Signal Analyzer
1720/1730
-
he very excellent signal analyzers of choice for field testing of QAM digital signals on your CABLE-TV SYSTEM.They demodulate and accurately measure the QAM signals carried through the cable system.They provide the measurement power the field technicians need for the latest 64-256QAM digital technologies and are very simple to use, measuring SNR(MER), EVM, Pre-BER, Post-BER, Constellation Diagram.
-
Product
RF Signal Source
DSG800A
-
The DSG800A delivers outstanding performance in the same class of economical RF signal sources with full frequency and power scanning capabilities, as well as AM/FM/ØM analog modulation, powerful pulse modulation and newly added IQ modulation. Compared to similar products, the DSG800A has the smallest footprint, light weight and superior portability, making it an excellent choice for educational laboratories, industrial production lines, development and research applications.
-
Product
Universal Voltage Signaling PCI Card w/ 5 IP Slots
PCI5IP
-
If you want to use IndustryPack¨ modules with your PCI system then the PCI5IP is the choice for you. The PCI5IP combines features you need with simplicity and speed. Up to 5 IP modules can be installed. 32 bit and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection.
-
Product
Signal, Module Insert, ITA, i2 MX, TriPaddle ,33 Position
510144006
ITA Module Insert
Signal, Module Insert, ITA, i2 MX, TriPaddle ,33 Position.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
Signal Module
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
