BoB
reroute signal paths to facilitate contact accessability.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
Terminal Block
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
OBD Protocol Diagnostics
-
Our innovative OBD Protocol Diagnostics comes with diagnostic break-out boxes and CAN network testers which can expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test ECU signals.
-
Product
Fifo Serial Analyzer 2 TO 2 Breakout Box
FLL222
-
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
Product
Breakout Box
-
A piece of electrical test equipment used to support integration testing, expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test signals
-
Product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
-
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
-
Product
Laser Levels
-
Fast, accurate and portable, PLS laser levels save time and money versus traditional layout methods using a bubble vials, plumb bobs or complex measurements. Compare the benefits PLS laser tools: Beam quality will be bright, thin and crisp. Drop tested with water and dust Ingress Protection (IP). Designed for the professional contractor with self-leveling technology. Green Laser Levels, Rotary Lasers, Point Lasers and Line and Combo Lasers.
-
Product
Modular Breakout System for Hardware-In-Loop Simulation
-
Designed in partnership with OPAL-RT Technologies, this Modular Breakout System combines a BoB feature set with the added flexibility of an FIU. By mating the FIU chassis directly to the BoB using our plug-in modules, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
Product
Breakout Boxes 9D thru 104DD Positions
D-SS Series
-
Silver Engineering's D-SS Series Breakout Box is aheavy duty break out box designed to withstand theabuses of the test environment. The heavy dutyconstruction and the use of high quality stainlesssteel connector shells and components insurethese units will last for years.
-
Product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 2m
193128-02
-
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
Product
Small, Low Cost, Uncooled InGaAs Camera
Bobcat 320 TE0 and WL Series
-
The Bobcat 320 TE0 and WL series are based on an in-house developed, uncooled InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 TE0 and WL cameras are offered with GigE Vision interface, 400 Hz maximum frame rate and feature low weight and power.
-
Product
Small InGaAs Camera For Short Exposures
Bobcat Gated Series
-
The Bobcat 320 Gated series is based on an in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 Gated cameras are able to provide maximum frame rates up to 400 Hz. The exposure time of the sensor is configurable from 100 ns up to 1 ms in steps of 100 ns, or from 1 ms to 40 ms.
-
Product
Small, High Performance InGaAs Camera
Bobcat 320 Series
-
The Bobcat 320 series is based on an in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 cameras are offered with frame rates of either 100 Hz or 400 Hz. The camera comes with a CameraLink or GigE Vision interface and features low weight and power.
-
Product
Small, High Performance InGaAs Camera With High Image Resolution
Bobcat 640 Series
-
The Bobcat 640 cameras are offered with high frame rate of 100 Hz. The camera comes with a CameraLink or GigE Vision interface and features low weight and power.
-
Product
Fifo Serial Analyzer Breakout Box
FLLBOB
-
FLL BreakOut Box FLLBOB is a breakout box specially designed to be used with the FLL and FSA serial analyzers. With FLLBOB it is easy to connect the PC to the serial line without having to make dedicated cables.
-
Product
Blue ESR/Low Ohms Meter
-
This is the fully-assembled, cablibrated and tested Blue ESR/Low Ohms Meter The latest and best Bob Parker design and successor to the famous Dick Smith ESR/Low Ohms Meter. This handy and affordable meter measures capacitor equivalent series resistance (ESR) in the circuit. ESR is a very important characteristic of capacitors greater than 1 ufd. This meter makes measurements which are often impossible to check with capacitance meters.
-
Product
Custom Breakout Boxes
-
Silver Engineering, Inc. has also provided many different forms of custom breakout boxes and adaptor cables to our customers. If you need something special, contact us.
-
Product
SM 1310/1550nm OTDR with VFL Blue Tooth Android
Bobcat
-
The Hand Held Bobcat OTDR has a generous 32 dB dynamic range and a short dead zone for testing FTTx fibers and networks up to the metro environment. It has an easy to read color display with fault finder, construction and expert/manual modes of operation. The OVP is shipped with Windows®/Telcordia SR-4731 compatible software that generates complete and professional documentation with the ability to include scope images and loss test results on the OTDR test reports.
