Fiberoptics
Field of optic fiber application.
-
product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
-
product
Audio Fiber Tracer
CFT-810
Motorized Polarization Controller. In addition to its basic function of adjusting polarization states in multi channels, it also provides convenient ‘save and recall’ functions. As a Scanning PC, it provides very powerful ‘auto scan’ modes with variable scanning speeds. Polarization states can be manipulated by either manual adjustment or remote control (GPIB, RS-232) using two quarter-wave plates in each channel of the PC1600. Additionally, the auto scan mode of FIBERPRO’s Motorized Polarization Controller has been upgraded in LPC, and it shows another auto scan mode of four quarter-waveplates with higher polarization extinction ratio when connecting two channels at a high speed. PC1600 is an essential tool to complete fiber-optic, multi-channel measurement systems such as WDM/DWDM as well as R&D (i.e. PMD experiments), and manufacturing.
-
product
S2 Penta Sensors
ULP-S2 PCI/V
Optomistic Products’ best-selling Sensor, the ULP S2 Penta Sensor, is relied upon for its versatility in accommodating most LED color and intensity test applications. Implemented in a unique and customizable 2-Part solution, the S2 Penta Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption:Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Loads: ‘Int.’& ‘Color’- 2Kohms min., 100pF max.Output Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: Typical response time: <10mS capture time; <100mS overall responsetime for color and intensity simultaneouslyFiber-Optic Probes: Can be paired with any Universal LightProbe Fiber-Optic Probe
-
product
CPS-8910 , Switch Device for PCI Express
784307-01
PCI Express, Cabled Switch Device—The CPS‑8910 is designed for large multiple-input, multiple output (MIMO) expansion configurations and system control on the PXI platform or software defined radio devices. The CPS‑8910 provides two PCI Express upstream ports and eight downstream ports for seamless system expansion. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel MIMO systems. You also can connect multiple CPS‑8910 switch boxes to a single PXI Express chassis to create massive MIMO systems with a Software Defined Radio Reconfigurable Device. The large data throughput capacity makes the CPS‑8910 an ideal data aggregator for massive MIMO systems. You can use the CPS‑8910 with copper or fiber-optic cables.
-
product
S2 Penta High-Sensitivity Sensors
ULP S2 PCI/V HS
The Universal LightProbe S2 Penta High Sensitivity Sensor features the same popular built-in color binning as the regular S2 Penta Sensor, and is designed test extremely dim LEDs, providing an analog output for intensity, ranging from 0 to 4 volts, corresponding to the LED’s luminous intensity in millicandelas. Implemented in a unique and customizable 2-Part solution, the S2 Penta High Sensitivity Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: <1.2s color & intensity outputs simultaneously (the brighter the LED, the shorter theresponse time)Fiber-Optic Probes: Wide Aperture Fiber-Optic Probe recommended
-
product
GPS over Fiber
*High Dynamic Range GPS to Fiberoptic Transmitter and Fiberoptic to GPS Receiver*Compact NEMA rated outdoor Fiber Transmitter provides +5VDC Bias for GPS Antenna LNA*Rack mounted Fiber Receiver provides 8 RF outputs and integrated monitoring and alarming*Cost effective solutions for distribution of GPS signal over long distance
-
product
Type T7 Fiber-Optic Cable for GPIB-140, 20 m
182805-020
2-Pin Male to 2-Pin Male, Core/Clad 62.5/125 um, 850 nm Wavelength Fiber-Optic Cable for GPIB-140A Extender - The GPIB T7 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T7 Cable with a GPIB extender to increase the cable length of your system up to 1 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T7 Cable is offered in different lengths.
-
product
PXI Remote Control Module
PXI Remote Control Modules allow direct control of PXI and PXI Express Systems through PCs and laptops. You can choose between copper (up to 10 m) or fiber-optic (up to 200 m) cable that connects to PXI or PXI Express modules in slot 1 of your PXI system.
-
product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-01K
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
product
GPIB T8 Cable, 2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender
183164-100
2-Pin Male to 2-Pin Male; Core/Clad 62.5/125 um; 1,300 nm Wavelength Fiber-Optic Cable for GPIB-140A/2 Extender - The GPIB T8 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T8 Cable with a pair of GPIB extenders to increase the cable length of your system up to 2 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T8 Cable is offered in different lengths.
-
product
High Speed Fiber-Optic Detectors
High speed fiber-optic detectors use special photodiodes with high speed electronic circuits to convert fast pulses in optical fibers to electrical signals for measurement. Unlike our optical receivers, these photodetectors do not include a transimpedance amplifier.
-
product
S2 Unicolor Sensors
ULP-S2 SCI/V
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
product
Universal LightProbe Sensor Six-Pack
S6P
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
Digital Secondary Systems
Schweitzer Engineering Laboratories, Inc.
SEL digital secondary system solutions (sometimes called digital substation solutions) help protect and control substation primary equipment using digital devices in the secondary system that transmit data via fiber-optic cables. Our flexible, scalable, and economical solutions are built with rugged, field-tested hardware that can withstand harsh environments. Select from two solutions:
-
product
OEM Products
Avantes, the leading OEM spectroscopy manufacturer and designer is the best choice for high-quality and highly reproducible spectroscopy solutions for low-volume and high-volume customers. We take pride in collaborating with our customers to supply the right solution. Whether you need a custom-configured optical bench or a specialized fiber-optic probe, we have the experience and dedication to make it happen. While we gladly develop custom-made devices, we also offer several modular and highly configurable OEM options.
-
product
Fiber Optic Measurement Systems & Sensors
MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.
-
product
Sensing System
FBG
A cost-effective FBG (Fiber Bragg Grating) interrogation system that includes a tunable laser diode, 6 photodiodes, and several fiber-optic couplers has been developed with very simple coniguration. Especially, it is not necessary to compensate the accurate wavelength because the wavelength sweeping is precisely performed in terms of the response time of which external cavity material is 5 msec. Moreover, time-varying temperature trends as well as spectra of FBGs can be observed through the front display.
-
product
DI-1000L-Pro
The DI-1000L-PRO combines the all-digital wide-view DI-1000L microscope with our ConnectorView™ Plus v2 Pass/Fail software for fast objective analysis of fiberoptic connector endfaces. Powered by it’s direct USB2.0 connection to your PC, the DI-1000L-Pro can provide you with automatically centered Analysis Reports and Summary Reports in Excel or text.
-
product
VME Bus Repeater
VME-5532L
Easily link your VMEbus systems via fiber-optic cable, with total electrical isolation, no EMI generation and high-noise immunity.
-
product
Fiber-Optic Receivers
These New Focus high speed fiber-optic receivers offer bandwidths up to 38 GHz for receiving fiber optic data while delivering the lowest noise and cleanest responses possible.
-
product
High-Speed, Fiber-Optic Reference Transmitters
Thorlabs' Reference Transmitters are designed for high-speed fiber optic test and measurement applications. They are fully-integrated and user-configurable solutions based on proven lithium niobate (LiNbO3) modulator technology driven by high-fidelity RF amplifiers.
-
product
Optical Fibers
Avantes offers a wide range of fiber-optic cables, which can be manufactured in a variety of lengths and configurations to meet your needs.
-
product
Laboratory Centrifuges
Centrifuge systems are designed for the development, test, evaluation and calibration of accelerometers and a variety of inertial devices. Centrifuges provide a cost-effective solution for simulating high-"G" environments in the laboratory. They support testing of devices such as MEMS-based Inertial Measurement Units (IMUs), low-cost quartz or silicon sensors, Ring Laser Gyros (RLGs), Fiber-Optic Gyros (FOGs), fuzes and crash sensors.
-
product
Miniature 12G/3G/HD-SDI Fiber Transport
SilverBULLET Series
Sometimes you just need that “silver bullet” - a simple solution that solves problems. Maybe it’s a quick connection to support temporary video and audio feeds, or perhaps just a rock-solid fiber-optic connection for single-link transport to and from a camera. MultiDyne’s SilverBullet Series offers an economical solution for broadcast-quality signal transmission on single-mode fiber. At just three inches, the SilverBullet offers a compact, interlocking architecture to ensure robust links that can fit just about anywhere. SilverBullets come in a compact carrying case that includes the DC power supplies. Ideal for a wide variety of broadcast and professional AV applications including field production, remote camera links, courtesy feeds, cross-campus production and pre-fibered venues.
-
product
Throwdown Fiber Transport & Converters
NanoBriX Series
We often forget all that happens along the media signal journey. Video and audio signals are converted, equalized and re-clocked as they move on and off fiber-optic networks. These same signals are manipulated and multiplexed as they are distributed through studio, venue and campus infrastructure on their way to headends and destination points. Audio signals are embedded and de-embedded alongside video streams, and properly mixed for varied broadcast and playout services. It’s almost too much to keep up with. MultiDyne’s NanoBrix Series assures that these many stages of the signal lifecycle are reliably addressed in one complete family. NanoBrix offers a comprehensive product line of miniature, rugged, quick-connecting throwdown solutions for temporary or permanent applications, including live TV productions, sporting venues, and broadcast facilities.
-
product
OEM, Embedded, and Custom Electronics
Picosecond timingPrecision analog and mixed signal processingDigital delay and pulse generationHigh speed photonics and fiberoptic timing distributionAerospace instrumentation and simulation
-
product
Highly Accelerated Stress Test Chambers
HAST
Our HAST systems have a modern design that's easier to use: Automatic humidity filling; Automatic door lock; A more square workspace; allowing more product to be loaded;Convenient, hermetic power-pin system for bias testing. We are now able to offer a hermetic port system to allow special signal lines like coax or fiberoptics to be run into the chamber.
-
product
HiCAM
The HiCAM is a gated intensified high-speed high-sensitivity imaging camera. It has an integrated fiber-optically coupled image intensifier, which offers a unique combination of high speed and sensitivity down to single photon level. Because the HiCAM does not need high intensity light sources, it is suitable for use in low-light level conditions.
