Mil-Std-1553
Interface Standard for Digital Time Division Command/Response Multiplex Data Bus
See Also: MIL-STD, 1553, Mil-Std-1760
-
Product
Military & Aerospace EMC Testing
-
EMC Technologies’ Melbourne and Sydney and also EMC Bayswater (south-east Melbourne) laboratories provide NATA accredited Electromagnetic Compatibility (EMC) MIL-STD testing of military equipment to MIL-STD 461 B, C, D, E, F & G. The scope includes most test requirements and methods called up by MIL-STD 461/2, allowing defence agencies, contractors and defence suppliers to prove compliance with the stringent EMC limits imposed on defence equipment and systems.
-
Product
Low Phase Noise Amplifiers
-
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
Product
CPCI or PXI MIL1553B & ARINC429 Board
MS 1700
-
The 1553 Board consists of dual Redundant 1553B Channel A & B and ARINC 429 Channels (6TX and 12RX).
-
Product
MEGA-POLE® Series
MEGA-POLE™
-
The MEGA-POLE filter series covers the standard frequency bands within the 30 to 450 MHz range. This new filter series provides excellent selectivity while maintaining very low insertion loss. The product line also has exceptional RF power handling capability with a high third order intercept point. The MEGA-POLE filter series can be used for transmitter applications to reduce power amplifier noise, harmonics and intermodulation products, to provide bi-directional filtering directly at a transceiver’s antenna port, or other applications requiring extremely linear, high power RF bandpass filtering. It has been designed for rugged military environments per MIL-STD-810.
-
Product
Standard And Custom Targets
-
Santa Barbara Infrared manufactures a wide range of targets for visible, and infrared/FLIR electro-optical testing. These targets complement our complete line of Visible and IR test products. Our targets are designed to function with one of SBIR’s target wheels. Utilizing a variety of manufacturing techniques, including conventional machining, photochemical etching, electro-deposition, electrical discharge machining (EDM) and laser cutting. SBIR targets are manufactured to exacting mechanical tolerances. SBIR manufactures all of the targets specified by MIL-STD-1859 and the Tri-Service Guide for thermal imager testing.
-
Product
18" Cables
CONV1553-4
-
Transitions from each SCSI-2 connector on a VME, VXI or CEI-600-6 front panel to two 18" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x-DS
-
A unique feature of AIM’s APE1553-x-DS modules is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
Fibre Channel Simulyzer™ Products
-
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
Product
Micsig Smart Oscilloscope
STO1000C/E
-
Shenzhen Micsig Instruments Co., Ltd.
*Up to 70Mpts memory depth, Zoom into a selected part of the captured waveforms to get more details. *Support serial triggering and decode (I2C, SPI, RS232/UART,CAN, LIN) and Aerospace and defence (MIL-STD 1553, ARINC 429). Two formats to display decoding, text and graphic.
-
Product
FlexMAX Modules
-
The FlexMAX modules must be inserted into a FlexMAX 1U or 3U chassis. MAX Technologies currently offers ARINC 429, Discrete I/O, MIL-STD-1553, ARINC 708, Serial ASYNC RS-232/422/485, HDLC / SDLC, CSDB, CAN Bus including CAN-FD, Digital to Analog (DAC) and Analog to Digital (ADC) modules. More modules will be added to the portfolio.
-
Product
Interface (PMC)
QPM-1553-TB
Interface
The QPM-1553-TB provides the highest level of performance, flexibility and interface density for MIL-STD-1553A/B via PMC (PCI Mezzanine Card) to Thunderbolt 3 device. The QPM-1553-TB is integrated with powerful software that reduces development time. All 1553 databus functionality is supported from our advanced API (Application Programming Interface).
-
Product
CPCI BUS Interface Card
Cpci301 MIL-STD-1553
-
MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator / Analyzer / Tester CPCI BUS Interface Card - The CPCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.
-
Product
1553 Bus Cables, Couplers, Terminators, and Kits
Terminator
Please review 1553 Bus Accessories to the right. You can also use the Login-Download link above (login required) to access all the Hardware Manuals with specific cable and connector information. Most 1553 Cards and ENET devices have optional 1553 Jack and AUX I/O DB cable assemblies. Please see the respective product pages part numbers tab. Most ARINC products include flying-lead cable assemblies.Please use the Contact link to email/phone sales for a login as needed.
-
Product
Aerospace And Defense Software (3000A/T/G X-Series)
D3000AERB
-
MIL-STD 1553 and ARINC 429 triggering and analysis for the InfiniiVision 3000A, 3000T, 3000G X-Series oscilloscopes, along with mask testing, advanced math, video analysis, and more.
-
Product
Horn Antennas
-
Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. Most compliance standards now require the use of such antennas. The latest version of Mil-Std 461E states the used of broadband double ridge guide horn antenna as the antenna of choice for frequencies above 200 MHz.
-
Product
RS-232 to EIA-530 Interface Converter
Model 62-1 / 62-2
-
FEATURES: Supports 10 Category I & 3 Category II Circuits; Full EIA-530 & RS-422 Compliance; DTE & DCE Models; Meets MIL-STD-188-114 Type 1/2; Up to 256 KBPS Data Rate. Conversion between RS-232 and EIA-530 is accomplished by the Models 62-1 and 62-2. These devices provide conversion for the entire EIA-530 interface which includes ten Category I circuits and three Category II circuits.
-
Product
Bus Controller
CPCI-1553-1
Controller
Single or dual UTMC 1553 Summit Controller, Bus controller, Remote terminal, Bus monitor modes.
-
Product
Particle Impact Noise Detection
BW-LPD-DAQ4000
-
Computer based controller with predefined MIL-STD test sequences stored (New)Create unlimited custom tests with multiple vibration frequencies and acceleration and other parameters to meet unique requirements (New)
-
Product
PCI Card
EXC-8000PCIe104/xx
-
The EXC-8000PCIe104/xx card for PCI/104-Express systems supports up to four dual redundant 1760 channels using the M8K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A,B). In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Modules For PMC
AMCX1553
-
MIL-STD-1553 Test and Simulation modules for PMC with 1, 2 or 4 dual redundant channels plus 8 Discrete I/O’s (on Rear-I/O).
-
Product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
-
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
Product
Rugged Embedded MIL-STD-1553Conduction Cooled PMC Card
AMCE1553-x
-
Rugged embedded MIL-STD-1553 conduction cooled PMC card.
-
Product
Intelligent Interface Card
IIB-1553-VXI-4C
-
The IIB-1553-VXI-4C is an intelligent interface card which provides 4 independent channels for full MIL-STD-1553 test, simulation and bus analysis functions on the VXI bus. All 1553A, 1553B, McAir and STANAG 3838 variants are supported. Each independent channel may be operated as a concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with a windowed Bus Monitor (BM), or as a stand-alone Chronological Bus Monitor (CBM) with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Each channel provides a variable amplitude dual redundant 1553 interface, with 2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Avionics System Power
58WS1-03
-
- 3Ø AC input per MIL-STD-704A- 1,500 Watts continuous, 3,000 Watts peak power- Environmentally sealed ATR style case- Continuous Background Built-In-Test (BIT) and ETI- EMI compliance
-
Product
AC Power Sources
GUPS (Global UPS)
-
AMETEK Programmable Power, Inc.
Elgar GUPS are ruggedized on-line "UPS's" that accept a broad range of worldwide utility and military AC input power. Without operator intervention, they automatically select the appropriate input power ranges to accommodate global operation. The GUPS Series has been specifically designed to withstand the rigors of mobile applications. They meet the vibration and shock requirements as specified in MIL-STD-810E, Methods 514.4 and 516.4. Their rackmounted aluminum chassis with stainless steel hardware withstands harsh environments and provides a strong, light weight enclosure.
-
Product
LISNs - Single Phase
-
Com-Power single-phase LISNs cover 9 kHz to 400 MHz in five series — 1x, 2x, 3x, 4x, and 5x — with current ratings from 20 A to 100 A for CISPR 16, ANSI C63.4, MIL-STD 461, DO-160, and CISPR 25 conducted emissions testing.
-
Product
One Channel Dual Redundant 1553 Controller
PCIe-Mini-1553-1TA
Controller
The ALPHI PCIe-Mini-1553-1TA uses DDC TotalAce communication device as its 1553 bus controller, or remote terminal with concurrent Bus monitor terminal. Dual controller has a Dual redundant channel with built in transceivers andtransformer. The controller has the capability to emulate up to 31 RT addresses simultaneously. The PCIe-Mini-1553-2in RT mode can filter on RT address, T/R, Subaddress.
-
Product
PC104 MIL1553A & MIL1553B Board
MS 1701
-
*Bus Interface - Standard ISA Bus (PC104 Interface)*One Dual Redundant MIL-STD-1553 Channels, Enhanced Mini-ACE BC/RT/MT Architecture*A periodic message insertion, Real-time bus playback with RT edit mode*Highly Autonomous Bus Controller Architecture, Message Scheduling*Bulk Data Transfers, Data Block Double Buffering*Asynchronous Messages, Retries and Bus Switching*Transformer or Direct Coupled 1553B Channels
-
Product
Rugged Ethernet System Supporting up to Four Independent 8000 Family Avionics Communication Modules
ES-9810/xx
-
The ES-9810/xx is a rugged ethernet system supporting up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched in a single system. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The ES-9810/xx is supplied with C drivers, including source code. Mating connectors and cable adapters for I/O connection can be purchased seperately.
