Protective Relay
acts as a circuit breaker in the event of a fault.
-
Product
Relay Test Kit
Relaystar-H60
-
HAOMAI Electric Power Automation Co., LTD.
Portable 6-phase protection test equipment for testing most types of modern multi-function protection relays, Output 6-phase AC current 6x0…32A Output 4-phase Voltage 4x0…300V.
-
Product
6-Phase Protection Relay Tester
HME-1200
-
HAOMAI Electric Power Automation Co., LTD.
Economical 6-phase Protection Relay Tester 6-phase current (6×30A) + 6-phase voltage (6×120V) output.
-
Product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix Topology Without Column Protection Resistors
782385-09
Terminal Block
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Primary Current Injection
PCI-600
-
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
Product
Intelligent MCC Controller
MM2
-
The Motor Manager II (MM2) combines control functions and comprehensive motor protection in one package. This compactdevice provides sophisticated control and protective relaying at significant cost savings over the discrete devices normallyfound in a low voltage motor control center (MCC).
-
Product
FTL Test Block
-
FTL testblock with dust cover and current disconnect pinThe FTL is a test block for interfacing substation devices (protection relays, fault recorders, revenue meters, ... ) to the voltage and current transformers and to other equipment on the system side of a power grid. The FTL test block uses disconnect pins to isolate the substation devices from the system side equipment. Once isolated, secondary injection can be performed using banana jacks on the front side of the test block.
-
Product
Single Phase Universal Protection Relay Test Set
S100A
-
S100A is the Universal Single Phase Protection Relay Test Set with 1*100A and 3*150V output, local control system for basic relay testing with manual operation.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix Topology Without Column Protection Resistors
782385-11
Terminal Block
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Integration
-
Schweitzer Engineering Laboratories, Inc.
Integrate protective relay and metering information into SCADA and plant control systems through secure networking and automation devices.
-
Product
Automatic Relay Test Set
DRTS 64
-
DRTS 64 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 6 Current and 4 Voltage generators simultaneously available.
-
Product
Digital Test Switch
FT-14D
-
Test switch solution for digital switchgear using current and voltage sensors. With the FT-14D Digital FlexitestTM switches, a new era of protection relay testing can be performed more safely, quickly and easily. The FT-14D switch allows a customer to integrate current and voltage sensors within digital switchgear and protective relays and thereby enable the Industrial Internet of Things.
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors
782385-06
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Protection Testing Library
-
The OMICRON software technology including the OMICRON Control Center, XRIO, and LinkToXRIO enables users to create specific test templates which adapt automatically to the actual relay settings. This functionality is the technological basis of the Protection Testing Library (PTL), a comprehensive test template library for a wide range of protection relays.
-
Product
Protection Relay Tester
PW866i
-
PW866i (6×32A, 4×300V) Protection Relay Tester could be used for testing all kinds of relays, also supports testing IEC 61850 combined relays. Its local control system is with 10.4inch LCD screen based on Windows system.
-
Product
Line Protection
-
Schweitzer Engineering Laboratories, Inc.
SEL transmission line protection relays provide subcycle line differential and multizone distance protection for a secure, reliable, and high-speed solution. Their fault-locating capabilities allow you to efficiently dispatch line crews to quickly isolate line problems and restore service faster.
-
Product
Distribution Operations
-
Schweitzer Engineering Laboratories, Inc.
SEL provides tools that work with protection and control relays to improve your system’s visualization and dynamic response—while still maintaining performance, situational awareness, and efficiency.
-
Product
Portable Multi Phase protection relay test set with GPS
TEST-630
-
Beijing GFUVE Electronics Co.,Ltd.
Test-630 multi Phase Universal protection relay test set have 6U6I output, it is a universal protection relay tester with eight pairs of binary input and four pairs of binary output
-
Product
SUPER-LIGHT Protection Relay Testing Equipment
L336i
-
Protection Relay Testing Equipment has long been associated with the heavy weight and the large size. So carrying the relay testing set to work site seems to be the job of engineers who are physically strong.
-
Product
Travelling Wave Fault Location Test Kit
PH Series
-
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
Product
Generator Protection Relay
SEL-700G
-
Schweitzer Engineering Laboratories, Inc.
The SEL-700G is the right solution for utility and industrial generator protection, with an autosynchronizer, flexible I/O, and advanced communications. Apply the SEL-700G for comprehensive primary and backup generator protection.
-
Product
FTS / FTP
-
The SecuControl FTS Test Block, used with FTP and LTP test plugs, provides a modular and fully finger-safe interface for secondary injection testing in IEC-based substations. With built-in CT shorting, keyed plug design, and predefined sequential operation, the FTS ensures safe, repeatable, and error-free testing of protection relays, fault recorders, and revenue meters. Its space-saving installation, flexible wiring options, and robust safety features make it the ideal solution for standardized and efficient testing across modern protection systems.
-
Product
IEC61850 Relay Test Set
NF802
-
NF802 is full digital IEC61850 relay test set, equipped with 8 optical ports, and powerful data processing capability, can realize full digital IEC61850 protection relay testing.
-
Product
Three Phase Power Calibrators And Tester Of Power Engineering Devices
C300B
-
Calmet Smart Calibration Devices
Three phase, class 0.02 and 0.05 power quality calibrator up to 120A (360A) and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
-
Product
Relay Test Equipment
-
Vanguard Instruments Company, Inc.
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers. The PCI-600 is versatile and can also be used in many other applications that require a high-current source.
-
Product
Relay Test Set
-
Relay testing equipment is a portable apparatus designed for checking the operating characteristics of protective relays on site. Rr Relay Testing Equipments are designed to facilitate routine test or periodic maintenance test of relays by simulating (as early as possible) fault conditions under which the protective relays are required to function. There are several approaches to the method of testing relays on site. The Relay Testing Equipments are secondary injection type and are intended to be used to test the relays after isolating them from live systems, either physically or electrically.
-
Product
Arc-Flash Protection
-
Schweitzer Engineering Laboratories, Inc.
Arc-flash detection technology significantly decreases the time it takes a relay to trip in response to an arc fault, thereby reducing hazardous incident energy. Combining light-sensing technology with fast overcurrent protection provides high-speed arc-flash detection and prevents overtripping for external faults. Arc-flash protection relays work with low- and medium-voltage apparatus and easily coordinate with other devices in utility-, industrial-, and commercial-scale power systems.
-
Product
Secondary Injection Relay Test Set
TD 1000 PLUS
-
TD1000+ is a protective relay test set especially designed to give the commissioning engineers a multitasking and highly reliable testing equipment. In comparison with T 1000 PLUS model, TD 1000 PLUS has two current outputs to test the differential relay characteristic curve, besides the pick-up current.
-
Product
Current Booster
PHPC01
-
PHPC01 current booster is an accessory which can work together with protection relay test kit to test transformer protection relay testing. It is specifically designed to supply high compliance voltage even at small current range.
-
Product
Environmental Chamber
REXMED REC-280
-
MOD. REC-280, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Power Calibrator And Protection Relay Test Set
CP11B
-
Calmet Smart Calibration Devices
Single phase, class 0.02 and 0.05 power quality calibrator up to 120A and 560VAC with programmable power quality parameters. It makes possible to make automatic test of electricity meters, measurement transducers, current transformers and protection relays.
