Passive Optical Network
Optical transmissions requiring no electrical power or active electronic parts.
-
-
-
Product
Fiber Optic Inspection & Cleaning
-
One of the most basic and important procedures for the maintenance of fiber optic systems is to clean the fiber optic equipment.
-
Product
33 GHz Optical Probe
DPO7OE1
-
The DPO7OE1 is a 33 GHz, low noise, broad wavelength optical probe with optical reference receiver (ORR) performance for 28Gbaud PAM4 and PAM2 (NRZ). The DPO7OE1 can be used as a conventional Optical-to-Electrical (O/E) converter for wide-bandwidth optical signal acquisition. The DPO7OE1 provides an FC/PC or FC/APC optical connection for Tektronix DPO/MSO70000 C/DX/SX model oscilloscopes for high-speed optical signal verification.
-
Product
Fiber Optic Light Source
-
Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.
-
Product
Optical Receiver Stress Testers
-
Developing next-generation optical receiver technology requires world-class stress testing. Use Keysight's automated calibration solution and get optical stressed eye results in one-tenth the time compared to a manual setup.
-
Product
HS-1760 Flight Rated XMC Network Interface Controller
XMC-1760-NIC-CC
-
Avionics Interface Technologies
Dual Channel configurations supporting NC/NC, NC/NT, or NT/NT - 75 Ohm single ended copper or 150 Ohm differential - Eight (8) opto-isolated discrete I/O lines - Rear I/O through the P16 connector - Conduction-cooling and/or conformal coating available - x4 PCIe interface to NIC interfaces, with DMA controller for data movement - Designed for extended temperature operations - ANSI Application interface supporting C development - Device driver support: Windows, Linux, & VxWorks (others on request)
-
Product
Ultra Miniature Rotating Optical Chopper
360C
-
A small compact low cost system suitable for OEM use. 10 Hz - 14,000 Hz standard chopping frequency range.
-
Product
Absolute Optical Inclinometer
A2T
-
The A2T is a single axis, digital gravity angle sensor. The A2T serves as a full 360 range absolute tilt sensing programmable level with either digital or analog output. Internally, a rotary bar coded disk is mounted to a weighted gravity driven wheel. A micro-controller strobes an LED to transfer the bar code image onto an optical linear array, then decodes the position every 2 mSec. Magnetic damping provides fast response and settling time while virtually eliminating overshoot and oscillations. An internal EEPROM stores field programmable parameters such as resolution, zero position, direction swap, and mode. This second generation design virtually eliminates the primary accuracy limitation of first generation inclinometers, which is sitation (hysteresis).
-
Product
500 MHz Passive Probe, 5mm, 10:1, 10 MOhm
PP025-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
(AOI) Automated Optical Inspection Systems
-
For automated defect detection and high-accuracy measurements. VisionGauge Online High-Speed AOI systems are perfect solutions for demanding high-throughput, high-resolution applications. These systems are perfect for a wide range of applications including MicroElectroMechanical systems (for MEMS inspection or MEMS measurement), semiconductor & discrete device inspection and measurement.
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Model Vector Network Analyzer
DZV-1
-
Digital Signal Technology, Inc.
DZV-1 is the vector network analyzer which can be measured the impedance and VSWR of the antenna, S Parameter of RF component and devices. It is small and low-priced. So, it is suitable for the production line, laboratory use, various testing applications, and the educational use. The communication between the DZV-1 unit and PC is done via USB, which is also used for power supply. The LOG-MAG characteristic, the phase-characteristic, the group delay frequency characteristics, the Smith chart, the polar coordinates, the SWR characteristic can be displayed on PC.
-
Product
Communications & Networking
-
Curtiss-Wright Defense Solutions
Our field-proven communications and networking solutions provide the core capabilities for secure mobile networks onboard land, sea, and airborne platforms. Leveraging advances in enterprise and data center technology, we design and create our rugged solutions to deliver high-performance connectivity on converged, application-aware networks in disconnected, intermittent, and (DIL) environments.
-
Product
Plastic Optical Power Meter
POFPM100
-
Shanghai Tarluz Telecom Tech Co., LTD
POFPM100 POF OPM used for the plastic optical fiber within 600 ~ 1000nm wavelength range, w, dBm units, five calibration wavelengths.
-
Product
Vector Network Analysers
LA19-13-03
-
The LA19-13-03 is our latest PC-driven Vector Network Analyser. It provides great flexibility, fast speed and wide dynamic range. It is useful for measuring a wide range of devices from 300 kHz to 8 GHz with 10 Hz resolution. By means of external links on the front panel, the internal couplers can be bypassed for direct access to the internal receivers. This flexibility allows, for example, high power amplifier measurements to be carried out using an external booster amplifier and couplers. It is housed in a small lightweight package making it very portable.
-
Product
Thick Film Passive Element
GBR-403
-
GBR-403 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). These elements are used in high voltage applications requiring high stability and resistance.
-
Product
Optics And Opto-Mechanics
-
Goniometers, optical rails/benches/stands, lens tubes and light guides.
-
Product
AGC, SNMP Bi-Direction Optical Receiver
NGB-9912, NGB-9924
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai NGB-9912 ( two-port ), NGB-9924 ( four-port ), is a type of high-grade AGC, Network management, Bi-direction, outdoor optical receiver. Various operating parameters of machine are microprocessor-controlled, LED display. Through the keys of machine can adjust and set EQ、ATT. Optional network transponder, implement remote network management. Large dynamic range of optical AGC characteristics, NGB-9912 ( two-port ), NGB-9924 ( four-port ) high output ,for FTTC, FTTN fiber access network. As a unit of CATV network RX, is a high performance, highly flexible, cost-effective CATV opical receiver.
-
Product
Optics Test Equipment
Software For Autocollimators And Test Telescopes
-
Optik Elektronik Gerätetechnik GmbH
Small investment - big improvement in measurement accuracy! The CROSSDETECT software is used to retrofit existing autocollimators of all types that are already equipped or can be equipped with a camera. The use of camera and software ensures that the measurement accuracy is increased by a factor of approx. 10 compared to visual measurements! The software can also be supplied complete with an autocollimator.
-
Product
Network Synchronization Device
VCH-003
-
The Network Synchronization Device (NCD) VCH-003 is intended for use on the Unified Telecommunication Network of the Russian Federation. Depending on the configuration of the NSS, VCH-003 can be used to generate and multiply synchronization signals of 2048 kHz and 2048 kbps as part of the PEG, as an OIG to restore synchronization signals received from the line at the transit node.
-
Product
250 MHz Passive Probe for WaveSurfer3000, 10:1, 10 MOhm
PP019-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
10G Ethernet/IP Network Infrastructure Testing Application
GENEM-X
-
GENEM-X is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on Siama’s carrier-class PROVA-X hardware appliance. GENEM-X allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model can use GENEM to validate service turn-up and modifications in the production network. GENEM is equally at home in a lab environment. It bundles wire-rate traffic generation and analysis capabilities with a network emulator and packet capture/replay function in a single software license.
-
Product
Optical Emission Spectrometers
-
Optical emission spectrometers (OES) and the measuring principle of the atomic emission are the ideal method and provide the perfect instrumentation for metal analysis in all different industrial businesses and environments.
-
Product
Optical Fiber 1×16 Switch
OFSW - 1 × 16
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×16 is a 1×16 prism optical switch. It can support 1 optical fibers input and 16 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
Smart Network Emulation for All Mobile Device Tests
CMWcards
-
Use R&S®CMWcards to prepare the tests you always wanted, but never found the time to set up. Create wireless signaling and application tests on the R&S®CMW500 wideband radio communication tester just by setting up a hand of cards – no programming required. Revolutionary card wizards and unique game rules guide you through setting up test sequences that fully comply with test specifications. Thanks to the R&S®CMW500 tester’s unrivaled multi-technology capability, R&S®CMWcards can be used to rapidly reproduce signaling scenarios for various wireless communications standards.
-
Product
Optical Light Source
TM3111
-
TM3111 optical light source is a handheld optical light source, It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer’s needs.
-
Product
Optical Sensors
-
Broadcom offers a wide range of optical sensors solutions including ambient light, RGB color, proximity and gesture sensors for a broad range of applications including:*Mobile / Computing - smart phone, tablet, laptop, gaming mouse, printer*Consumer Electronics – TV displays, handheld game console, digital camera*Lightings – Industrial / commercial lightings, residential lightings, outdoor street lightings*Automotive – Instrument panel illumination*Medical Diagnostic Equipment*Industrial Instrument*Contactless switches*White Goods*Sanitary Products*Health / Fitness Products
-
Product
Optical Receiver Stress Test Solution
N4917B
-
The N4917B software provides an automated standard compliant stressed receiver sensitivity test according to 100GBASE-LR4, ER4 and SR4 test specification. In order to do this kind of test, several test instruments such as a bit error ratio tester, digital sampling oscilloscope, optical reference transmitter and tunable laser source are required to operate together to achieve a compliant, repeatable optical stressed eye. This stressed eye is then fed to the receiver under test, where bit error ratio is measured under the stress conditions as defined in the standard.
-
Product
HDLC RS-232 / RS-422 / RS-485 Passive Tap Module – USB Port
VERSA-TAP™
-
Versa-Tap protocol analyzer offers a powerful hardware solution that features state-of-the art electronics and provides exceptional data-logging/analyzer capabilities at a fraction of the cost of the nearest competitor.
