Battery Internal Resistance Testers
See Also: Resistance Test, Battery Conductance Testers
-
Product
Franklin Tester
Model FT1
-
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
Go No Go Testers
-
Go No Go Testers are developed in portable formats. Typically these are utilized at 'I' Level and 'O' Level test requirements and clear the aircraft LRU for flight.
-
Product
High Performance UV Nanoimprint Resist
AMONIL®
-
UV Nanoimprint is a mechanical molding technique. A template made from quartz or a flexible elastomer with a 3D relief is brought into intimate contact with a UV-curable resist spin-coated on top of a substrate. Applying low imprint pressure at room temperature features are filled within seconds due to the low viscosity of the imprint resist. The resist is hardened via UV-light through the backside of the template. Finally substrate and template are separated. The replicated resist relief can further be transferred into the substrate via RIE-process or used as functional element.
-
Product
Medical Electrical Safety Testers
-
Shanghai Beha Electronics Co., Ltd.
Special purpose AC milliammeter designed to measure hazardous leakage current from electrical appliances and other power line operated equipment.
-
Product
Battery Crush Nail Penetration Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL battery crush nail penetration tester is used to simulate the use, transportation, storage and disposal of various types of batteries under certain temperature conditions, when the battery is crushed (such as compacted garbage) or nail penetration, and to judge the battery safety performance. The battery is qualified as no disintegration, no rupture, and no fire.
-
Product
Battery Test System
WBCS3000Ls / WBCS3000Le
-
Low current model8 channel battery cycler (expandable up to 128 channels)max. voltage range : ±5Vmax. current range : - Model WBCS3000Ls : ±10mA - Model WBCS3000Le : ±100mACustomized specification is available.
-
Product
PITOT STATIC TESTER
ADSE 745
-
The ADSE 745 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fix and rotary wing. The multi-pressure outlets option can suit the more complex pilot-static-systems. This Pitot Static Tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.
-
Product
Insulation Testers
-
Rishabh Instruments Pvt. Ltd.,
Rishabh Insulation Tester is a Digital Insulation Tester with selectable test voltage up to 10kV and Insulation. Resistance measurement upto 20 TΩ. Ideal for testing insulation in live switchyards.
-
Product
Screwdriver Probe Voltage Tester
SD-328H
-
Easy and safeTests AC/DC voltage from 110-250VHandy pocket screwdriver is a fully functional voltage testerInsulated screwdriver shaftConvenient screwdriver tip and pocket clip
-
Product
Noise and Vibration Tester
-
SKF Condition Monitoring Center
High tech analysis and measurement such as frequency analysis (FFT) and further advanced analysis pinpoints faults. Spectral masks help to optimize the bearing performance in the particular customer application.
-
Product
Single Head Component Testers
34XX
-
Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes, darlingtons and matched dual transistors. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3402E or 3403E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
Product
Programmable Insulation/Withstanding Voltage Tester
-
AllWin Instrument Science and Technology Co., Ltd.
1. Electric safety wall detecting2. Test mode programmable3. ACW to DCW to IR toggle automatically4. (40.0~400.0)Hz
-
Product
HV Tester
-
For High Voltage withstand, breakdown testing of electrical insulating systems.For Dielectric Strength testing of electrical / electronic components, small appliances, tools, motors, machines etc.
-
Product
PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, Internal Termination, Failsafe
42-781A-222
Microwave Relay Module
The 40-781A-222 (PXI) and 42-781A-222 (PXIe) are dual failsafe SPDT 26.5 GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
COF Testers
-
Coefficent of Friction Testers are composed of a motorized test stand, digital force gauge, COF sled and table and specialized software. COF testers measure the static and kinetic coefficients of friction of plastic film, sheeting and similar thin materials.
-
Product
Network Cable Tester
AVJoG
-
*A two box solution to testing AV panel installations. *Each box only 150mm square.*Easy to use with only one button operation. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *6V battery or Mains use.
-
Product
Electronic Ballast Tester
WT4000
-
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
Product
Multi-Operational Surge Tester
M Model
-
Portable compact Multi-Operational Surge Tester that contains a multi-position carrying/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or field. The "M" is the perfect choice for your complete preventive/predictive maintenance testing - DC Hi-Pot testing, handheld resistance meter* testing and the capability of testing fully assembled grounded motors without rotating the rotor position.
-
Product
Primary Adhesive Tester
DRK129
-
Shandong Drick Instruments Co., Ltd.
DRK129 Primary Adhesive Tester is applicable in primary adhesive tests of pressure sensitive adhesive tapes, adhesive bandage (plaster), label, protective films and other products.
-
Product
HDCD Battery Charge Tester
-
HD Power Test Equipment Co.ltd
HDCD Battery Charge Tester is mainly used for the charge test of the lead-acid battery of the backup power supply in the telecommunications, mobile, substation, railway transportation and pertrochemical industry power DC industries. It keeps the constant communication maintain between the battery charge ensuring a perfect charge.Battery charge tester is designed using intelligent three-stage charging mode to achieve the function of automatic conservation between charging and floating charge. It also can on-line detect the voltage of the whole battery, real-time display and record the voltage of whole battery. The tester can automatically accomplish charging after setting the parameter of voltage, current, time and capacity.
-
Product
Axis Play Tester
PMS 3.5 | VP 225012
-
Maschinenbau Haldenwang GmbH & Co. KG.
The axis play tester PMS 3.5 is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the PMS 3.5 easy to use.
-
-
-
Product
PCIe LVDS Digital Waveform Acquisition - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7735-X8
Digital Waveform
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
-
Product
Demattia Flex Tester
UI-FT33
-
Demattia Flex Tester & Demattia Flex-Cracking Tester is used to test rubber crack growth under repeated bending or flexing. Unuo manufactures demattia flexing fatigue tester which meets test methods of ASTM-D813, GB/T 13934, HG 2873, ISO 132:1999(E), BS 903-A10 and etc.
-
Product
Blade Socket Tester
RV 7
-
The RV 7-Blade Socket Tester offers a fast, easy way to isolate a lighting problem to the trailer or towing vehicle. A must have for anyone who deals with hitch and lighting hookup installations, it tests the output of towing vehicle’s RV 7-blade lighting socket.
-
Product
Caraya Unit Tester
-
Caraya is a new experimental open source assertion and unit testing framework for LabVIEW. It takes a whole new approach to unit testing; your VI is your test. Caraya allows you to convert your manual test VIs you use for debugging into unit test cases with nearly no effort. Even running the tests is easy, just run the test case VI. Caraya significantly lowers the barrier for developers to write unit tests leading into improved overall code quality in real-world projects where developers don’t always have the luxury to write unit test cases first.
-
Product
SpaceWire RMAP Tester
121
-
The SpaceWire RMAP Tester is a software test platform that provides the means to validate SpaceWire RMAP target implementations and to test the generic functionality of any unit that relies on the RMAP protocol for its configuration and control.
