Digital Input-Output
Input/output of digital values.
-
Product
Digital I/O
IP-DIGITAL482
Digital I/O Module
IP-DIGITAL482 is a single-wide IndustryPack configured to maximize the number of digital I/O lines. The 48 lines are accessible as individual bits or as bytes. These lines may also be used for 8-bit and 16-bit I/O with handshake lines. IP-DIGITAL482 is a drop-in replacement for the IP-DIGITAL-48.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786163-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Digital I/O Board
3512
Digital I/O Module
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
14-Bit Digitizer
PA72D14130
Digitizer
The PA72D14130 is a 14-bit digitizer, capable of capturing waveforms at speeds up to 130Msps. An onboard offset voltage source allows capturing offset signals while still using the optimal range for maximum ADC utilization. Two onboard filters allow suppression of out-of-band noise. The 64MWord onboard memory enables capturing very long waveforms, or sequentially capturing multiple signals with minimal intermediate bus communication.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5912-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
PXI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module
778964-01
Digital I/O Module
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6515 is an industrial digital I/O interface with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2230-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
50 MHz 32-CH High-Speed Digital I/O Card
PCIe-7350
Digital I/O Module
ADLINK's PCIe-7350 is the advanced version of hot-selling PCI/PCIe-7300A featuring high-speed digital I/O with 32-channel bi-direction parallel I/O lines. The data rate can achieve up to 200 MB/s through the x1 PCI ExpressR interface. The clock rate can support up to 50 MHz internal clock or 100 MHz external clock, which is ideal for the applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 250 MS/s on 4 Channels Digitizer, 625 GS/s AWG on 4 Channels
DN2.822-04
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PXIe Digital Stimulus/Response with PPMU: 250 MHz, 16 Channels
M9195B
Digital I/O Module
The Keysight M9195B PXIe digital stimulus/response (PXI DSR) module is ideal for IC design validation and production test environments. The PXI DSR provides 16 bi-directional digital channels with programmable logic levels and can be configured for synchronized cyclized digital data, for parametric measurements, or for static digital IO.
-
Product
Digital Signal Processor
FalconX
Digital Signal Process
The FalconX is a radically new digital signal processor that combines a cutting-edge hardware platform with patented SITORO® signal processing technology, uniting unprecedented technical performance with an innovative “plug & play” design.
-
Product
Sixteen Channel 12-Bit Analog Input/Output Cards
PCI-A12-16A
-
Model PCI-A12-16A is a multifunction, analog-to-digital, digital-to-analog, and digital I/O card. It accepts up to 16 single-ended inputs or eight differential inputs. Inputs are protected against over-voltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts. Conversions can be initiated in any one of three ways: (a) software command, (b) external start commands, or (c) on a timed basis using on-board programmable counters. Converted data may be transferred to the computer by one of two software selected methods: (a) polling for the end-of-conversion signal, or (b) by generating an Interrupt when the end-of-conversion signal occurs.
-
Product
Digital multimeter, 6 digit, basic Truevolt DMM
34460A
Digital Multimeter
Keysight's Truevolt 34460A digital multimeter (DMM) is the entry level into Keysight's 6 digit family. The Truevolt Series of DMMs is the next generation of bench/system DMMs from Keysight. Only with Keysight's Truevolt DMMs can you:
-
Product
SH68-68-D1, Shielded Cable, 5 m
183432-05
Digital Cable
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
Product
64-Channel Boundary-Scan Digital I/O Scan Module
JT 2111/MPV DIOS IDC
Digital I/O Module
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
Product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels
M4i.4471-x8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them.
-
Product
PCIe RazorPlus Express 16-Bit Digitizer
Digitizer
The GaGe RazorPlus Express CompuScope is a dual-channel 16-bit digitizer supporting A/D sampling rates up to 500 MS/s with up to 250 MHz input bandwidth.
-
Product
32-CH Discrete Output Module
HSL-DO32-M-N/HSL-DO32-M-P
Digital Output Module
Slave ID consumption: 2 consecutive from odd"N" type for NPN sinking type outputSwitch capacity: Single channel 500 mA; all channels 60 mA at 24VDCPhoto couple isolation voltage: 2500 VrmsResponse time: ON→OFF: 180µs, OFF→ON :1.2µsLED indicator: Power, Link and Output statusPower supply: +10V to +30 VDCOperating temperature: 0 to 60°C
-
Product
NI-5752B, 50 MS/s, 12-Bit, 32-Channel, Kintex-7 FPGA Support, Digitizer Adapter Module for FlexRIO
784062-01
Digitizer
The NI‑5752B is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples 32 channels at 50 MS/s. You can use the NI‑5752 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions. The NI‑5752B is compatible only with PXI FPGA Modules for FlexRIO that have Kintex‑7 FPGAs.
-
Product
PXIe-5775 , 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Digitizer
785592-01
FlexRio Digitizer
The PXIe-5775 is a PXI FlexRIO Digitizer that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PXIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Input-output Module
MOV48
-
M-module MOV48 is installed on the mezzanine carrier - module NM-M or MEZABOX and is connected to them via a local information highway.
-
Product
PXIe-5624, 2 GS/s, 12-Bit PXI IF Digitizer
783132-01
IF Digitizer
The PXIe‑5624 is optimized for superheterodyne receiver architectures. It features an onboard digital downconverter, which converts IF signals to I/Q data. As a result, you can use the PXIe‑5624 either as part of a PXI Vector Signal Analyzer or as a stand-alone IF digitizer.
-
Product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-02
Digital I/O Adapter
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785170-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels
M4I.4480-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Output, Bank-Isolated Digital I/O Device
778836-01
Digital I/O Module
The PCI-6514 is an industrial digital I/O interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in … software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
NI-5772, 1.6 GS/s, 12-Bit, 2.27 GHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
782097-01
Digitizer
The NI‑5772 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that can simultaneously sample two channels at 800 MS/s or sample one channel at 1.6 GS/s with over 2 GHz of analog bandwidth. You can use the NI‑5772 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Digital I/O Vector Development Software
DIOEasy
Digital I/O Module
DIOEasy offers test engineers an efficient tool for developing, debugging, and executing digital test vectors for Marvin Test Solutions' GX5050 series, GX5150 series, GX5280 series and GX5291, GX5292, GX5293 and GX5295 dynamic digital instruments.Digital I/O (DIO) systems are very complex and typically require a substantial amount of programming effort to define data vectors. In order to simplify vector development, Marvin Test Solutions developed Windows-based DIOEasy, providing users with an easy to use interface. Toolbars and menus provide quick access to vector editing and viewing tools.
-
Product
32-CH DI & 32-CH DO 12 MB/s High-Speed Card
PCIe-7200
Digital I/O Module
- x1 lane PCI Express interface- 32-CH TTL digital inputs and 32-CH TTL digital outputs- Up to 12 MB/s transfer rate- Onboard programmable timer pacer clock- Support handshaking digital I/O transfer mode- Bus-mastering DMA for both digital inputs and outputs- 5 V power available on connectors- Compact, half-size PCB
-
Product
Digital Multimeter, 6 Digit
34465A
Digital Multimeter
Resolutions up to 6 digitsReading rates up to 50,000 readings/sMemory up to 2 million readingsCurrent ranges from 1 A to 10 AUSB and LAN interfaces, optional GPIBBenchVue software enabled: Do more with your PC and instrument together, no programming required. Easily control your DMM, quickly build automated tests, log measurements and save precious time.
