Ultra High Voltage
voltage from 1000 to 1600 kV.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-153-HI
Programmable Resistor Module
The 40-230-153-HI (PXI) and 42-230-153-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 11.32MΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Voltage Protection
-
Are solid state voltage sensing relays with electromechanical output contacts built in a fully draw out case format. Designed for application on AC & DC voltage systems, these relays are ideally suited to monitor power supply voltage levels wherever high accuracy and reliable, maintenance free operation is essential. All power to operate the relays is derived from the sensed input voltage therefore an auxiliary supply is not required.
-
Product
Ultra High 4.09 (116.00) - 10.00 (283.00) General Purpose Probe
EPA-2X-2
General Purpose Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-252-HI
Programmable Resistor Module
The 40-230-252-HI (PXI) and 42-230-252-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Current / High Voltage Pulsers
DEI Division
-
Berkeley Nucleonics Corporation
is optimized for high impedance capacitive loads, driving extraction grids and deflection plates, and pulsing or gating power tube grids. It generates an output voltage of 6,000 volts with rise and fall times less than 60ns, with very flat voltage pulses from 160 nanoseconds to DC into a capacitive load.
-
Product
PXI High Voltage Programmable Resistor Module, Connector
40-230-323-HI
Programmable Resistor Module
The 40-230-323-HI (PXI) and 42-230-323-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 3.55kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage Testers
GLP2
-
GLP2-tester series are the result of our experience in manufacturing following “customer based technology“ for more than 20 years. With precise, intelligent test processes the testers set the standard regarding operating ease, modularity, functionality, measurement accuracy and performance.AC tests up to 100 kV. DC tests up to 98 kV. Suitable for production testing of luminaries, white goods, coils etc.
-
Product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 4-Channel, 1-Pole
42-321-100-HI
Multiplexer Module
The 40-321-100-HI (PXI) and 42-321-100-HI (PXIe) are dual 4-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
High Voltage Linear Amplifier
A800X
-
This unit is a version of A800 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A800X functionally identical with A800 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
Product
Ultra High 3.83 (109.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-72U-10
ICT/FCT Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
PXI/PXIe High Voltage Power Relay Module, 7xSPST With Hardware Interlock
42-323-900-HI
Relay
The 40-323-900 (PXI) and 42-323-900 (PXIe) are 7xSPST relay modules suitable for applications requiring high voltage power switching with high density. They have current handling up to 0.25 A, cold switching up to 9 kVDC/9 kVAC peak and hot switching up to 7.5 kVDC/7.5 kVAC peak.
-
Product
PXI 18xSPST High Voltage Power Relay Module
40-330-002
Relay
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
Product
High Voltage Switching Test System
-
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
Product
High Voltage EMC Surge Generator
TM510
-
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
Product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783284-01
Voltage Input Module
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
Product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Bias Ball Probe
POGO-1L24-10-S
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
High Voltage Dry Reed Relays
Series 60 & 65
-
High voltage relays - chassis mounted, up to 15kV. Tungsten switches with power rating of 50 Watts maximum. Series 60 has solder terminals and nylon chassis mounting studs
-
Product
Ultra High 1.16 (33.00) - 9.70 (275.00) Long Travel Bead Probe
BPLT-25F-9.7
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
Product
Ultra Slim Fanless Embedded Computers
ARK-1000 Series
-
ARK-1000 series features ultra-small and low power consumption designs that offer sufficient storage and PCIe expansion for space-limited applications.
-
Product
LXI High Voltage Switching - 30xSPST Plugin Module
65-233-902
General Purpose Relay Module
The 65-233-902 plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-325-HI
Programmable Resistor Module
The 40-230-325-HI (PXI) and 42-230-325-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-132-HI
Programmable Resistor Module
The 40-230-132-HI (PXI) and 42-230-132-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 26.7kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Power Multiplexer, Dual 12:1
40-331A-002
Multiplexer Module
The 40-331A-002 dual 12:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Bias Ball Probe
POGO-1Z1-10-S
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
LXI High Voltage Multiplexer Plugin Module
65-231-904-HI
Multiplexer Module
The 65-231-904-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 2-Pole
42-321-121-HI
Multiplexer Module
The 40-321-121-HI (PXI) and 42-321-121-HI (PXIe) are quad 5-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-010-HI
Programmable Resistor Module
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
CMOS Drive High Voltage SIL Reed Relays for up to 3 kilovolts
Series 101
Reed Relay
Direct drive from 74HC/HCT Cmos SIL Relay. Dry or Mercury Wetted switches. 5 Volt coil for 1A dry version is 1600 0r 3000 Ohms
