-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
EW System Test Set
MS 1107
-
PSS LRU Test Set is used to test the RWR (Radar Warning Receiver) system by simulating the input signals and testing the output signals.
-
Product
PSG Vector Signal Generator, 100 kHz to 44 GHz
E8267D
Vector Signal Generator
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
Product
3U OpenVPX FMC Carrier
VF360
-
Sundance Multiprocessor Technology Ltd.
The VF360 is a 3U OpenVPX module that leverages on Altera Stratix® V FPGA and Texas Instruments KeyStone Multicore DSP technology to provide an ultra-high bandwidth processing platform, ideally suited for computation and bandwidth intensive applications such as Radar, Networking, SIGINT, EW, SDR and Video.
-
Product
USB Power Sensor - 10 MHz to 18 GHz, True-RMS Average
GT-8553B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
Activity Detection Unit
DG009-M1
-
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
Product
Agile Signal Generators (UXG)
XSeries
-
Get a powerful building block, whether you need a dependable LO or a scalable threat simulator More accurately simulate multi-emitter scenarios for radar, EW and antenna test with the fastest switching, phase coherency, and extensive pulse-modulation Test sooner and increase confidence in EW system performance by generating complex signal simulations when you need them Increase the reliability of your test system: the UXG is a slide-in replacement for legacy fast-switching sources
-
Product
Airborne Video Delay Board
MS 2006
-
- Spartan FPGA based Design- Customized design for delaying & switching video inputs to RF section- Interface with EW Signal Processor Unit- Two channel video inputs and control- Video Signal Delay from 1ns to 1ms- Over duty Indications- Inhibit Control- Discrete Interface
-
Product
DRO/VCO Modules
-
The Analog Devices portfolio of dielectric resonant oscillators (DROs) and voltage controlled oscillators (VCOs) offer excellent output power and phase noise performance over temperature and cover a range of applications and uses to meet the needs of industrial, medical, aerospace and defense, EW, ECM, and communications markets. Our DRO modules are a natural choice for applications in fixed tuned or narrowband tunable configuration, while our selection of VCOs play a key role in providing reliable frequency generation for RF and microwave communication and test systems.
-
Product
RF Peak Power Sensors
-
These sensors feature real-time processing and hardware triggering with advanced PC software to capture even the most elusive signals. Measure pulsed, bursted, and modulated signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), consumer electronics (WLAN and WiFi 6), as well as education and research applications.
-
Product
Dual-Directional Couplers
-
KRYTAR’s directional couplers are uniquely designed for systems applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. These couplers provide simple solutions for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted applications the compact size makes KRYTAR directional couplers ideal solutions.
-
Product
Ruggedized SSPA 4 to 8 GHz, 40 W GAN Hybrid Module
AMP1110
-
Exodus Advanced Communications
Ruggedized Solid State Power Amplifier. Our Best in Class Power Amplifier AMP1110 a 4 to 8 GHz, 40 W Minimum Saturated Power output module. The AMP1110 is a Class AB linear GaN hybrid design with instantaneous bandwidth. Other features include 4.0dB Peak to Peak flatness and 12A Max Consumption. This AMP1110 has Built-in protection circuits, high reliability and ruggedness. It is suitable for any application such as EW, EMI/RFI Lab, and High Power testing.
-
Product
4-Way Power Splitter/Combiner
ZN4PD1-183W+
-
Mini-Circuits’ ZN4PD1-183W+ is a 4-way 0˚ splitter/combiner covering a wide range of applications from 4000 to 18000 MHz including test and measurement, EW, SatCom and more. This model is capable of handling up to 30W RF input power as a splitter and passing up to 4A DC current from the sum port to alloutput ports (100mA each port). Its outstanding combination of high power and low loss minimize intrinsic losses and provide excellent signal fidelity from input to output. It also provides high port-to-port isolation, excellent VSWR and low amplitude and phase unbalance. It comes housed in a rugged aluminum alloy case with SMA connectors at all ports.
-
Product
mmWave and Microwave GaAs Frequency Dividers and Prescalers
-
Keysight Technologies provides MMIC frequency dividers and prescalers ideal for high-frequency communications, microwave instrumentation, and electronic warfare (EW) radar system applications. These devices operate from DC to 16 GHz and provide a large input power sensitivity window and low phase noise.
-
Product
3U OpenVPX FMC Carrier
VF361
-
Sundance Multiprocessor Technology Ltd.
The VF361 is a 3U OpenVPX module that leverages on the ALTERA Arria ® V SoC FPGA, ARM Cortex-A9, and Texas Instruments Keystone Multicore DSP technology to provide a high bandwidth processing platform, ideally suited for computation and bandwidth intensive applications such as RADAR, networking, SIGINT, EW, SDR and Video.
-
Product
Microwave Power Amplifier 1/4 Watt, 2 GHz to 50 GHz
GT-1050B
-
The Spanawave/Giga-tronics GT-1050B Microwave Power Amplifier offers linear high-power amplification across multioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
-
Product
Electronic Warfare MMI and HMI Simulators
MS 1600
-
The EW IFU (Electronic Warfare Interface Unit) interfaces between Cockpit electronics viz., RWR Display Unit (DU), New control Box (NCB), CMDS Control/Display units and Simulator Host Computer (HOST). The EW IFU transmits the status of the cockpit control units to the host, receives display data from the host and transfers the same to RWR DU, NCB and CMDS CCU/CDU. The display data for the RWR DU received from the host would comprise of the complete symbol data in respect of emitters that are to be displayed based on the data from the Instructor Station (IS) and control input from the cockpit. The display unit receives and presents the data as symbology on the display screen. The EW IFU based on the PC–AT.
-
Product
USB Power Sensor - 100 MHz to 20 GHz, Average, Peak (Pulse), Pulse Profile
GT-8555B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
Compact Timing Systems
NanoSync IV & NanoSync IV Low Profile
-
The NanoSync IV is a small form factor GPS Position, Navigation, Time (PNT) and Frequency reference system that provides multiple reference outputs and includes support for NTP & PTPv2 IEEE 1588-2008. The NanoSync IV has a Rubidium oscillator and is available with a civilian C/A GPS receiver or SAASM (Rockwell-Collins MPE-S GB-GRAM or Trimble Force 22E MRU GPS receiver) for military users. The NanoSync IV is packaged in a small, rugged enclosure ideally suited for embedded electronic warfare applications.The NanoSync IV-SA-Rb has been demonstrated to be compliant to the Joint Airborne SIGINT Architecture (JASA) Version 3.0, Annex 1, for Time, Frequency, Navigation and Geodesy (TFNG), making it suitable for Electronic Warfare (EW) COMINT and ELINT applications in fixed site, airborne and shipboard environments.
-
Product
SDLVA Modules
-
Analog Devices, the world-class supplier of complete MMIC-based solutions for communication and aerospace and military markets, offers two successive detection log video amplifiers (SDLVAs) that operate over the 0.6 GHz to 20 GHz and 2 GHz to 20 GHz frequency ranges, respectively. They feature power limiter circuitry at the RF input and carry a Class 1A ESD rating (250 V HBM). They are available in miniature connectorized module packaging and are ideal for designers with space and power-constrained applications, including EW and ELINT receivers, DF radar, ECM, IFM systems, and missile guidance.
-
Product
OEM Software Services
-
Shoghi Communications has been a designer of various ISR sensors, a System integrator with multitude of technologies covering ISR and EW and a premier defense contractor for various customers including defense and intelligence agencies across the world. The various projects for customers in the interiors and border areas of their countries have given Shoghi valuable experience to work in various types of terrain and weather conditions. This has resulted in the development of a very niche skill set which could be useful for both new OEMs as well as system integrators for various types of white labelled products and services in the fields for software development for auxiliary tasks.
-
Product
Frequency Synthesiser
RA062-F2
-
The RA062-F2 is a multiple LO module used to generate three pairs of LO signals, each pair being phase matched in order to provide the capability to drive two phase and amplitude matched, high sensitivity narrowband receivers such as might be required for an EW receiver system with DF functionality.The Stepped Frequency Synthesiser is based upon Direct Frequency Synthesis, DFS, whereby the 1GHz input reference signal is multiplied, filtered and mixed to generate a given number of isolated and filtered single tone CW signals from the 1GHz comb. A finely tuned signal is then generated using a multi-way switch to select between the 1GHz spaced CW tones and mixed with fine resolution signals generated using a custom DDS/VCO PLL network. In this way finely tuned signals can be generated between 7.5GHz and 23GHz.
-
Product
UXG X-Series Agile Signal Generator, Modified Version
N5191A
Signal Generator
et closer to reality: simulate increasingly complex signal environments for radar, EW & antenna-test Test sooner & increase confidence in EW systems by generating signal simulations when you need them: the UXG is a scalable threat simulator Use pulse descriptor words (PDWs) to generate long pulse trains & individually control pulse characteristics Quickly characterize antennas over a wide frequency range with fast frequency tuning Performance without requiring an export license
-
Product
USB Power Sensor - 100 MHz to 8 GHz, Average, Peak (Pulse)
GT-8551B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
Ultra Wideband Recorder (UWR)
-
Kratos Defense & Security Solutions, Inc.
Ultra Wideband Recorder provides RF Recording and Playback for instantaneous bandwidths up to 4 GHz across any frequency band(s). The system enables cost efficient testing of wideband RF systems for SatCom or other applications and data collection for EW applications across a wide band of RF spectrum.
-
Product
Preselectors and Switch Filter Banks
-
Our preselectors and switch filter banks offer low noise figure, high dynamic range, state-of-the-art filter rejection with high channel-to-channel isolation front ends, realized in compact building blocks, designed in custom form factors. Applicable markets include: EW, missiles, radar, communications and space.
-
Product
3U VPX GPGPU Modules
-
Curtiss-Wright Defense Solutions
For systems requiring enhanced situational awareness or using deep learning frameworks for artificial intelligence applications, these highly engineered modules provide a field-proven hardware foundation. Answering the growing demand for (AI) and high-performance processing in deployed EW and ISR applications, our 3U VPX GPGPU modules are designed to deliver advanced capabilities in a highly rugged, SWaP-optimized board.
-
Product
USB Power Sensors 10 MHz to 26.5 GHz
GT-8554B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
Mezzanine FMC
FMC-516
-
Curtiss-Wright Defense Solutions
The FMC-516 provides the low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of data delivered to the FPGA host through the FMC-516.
-
Product
FPGA Processor Card
CHAMP-FX4
-
Curtiss-Wright Defense Solutions
Integrating FPGAs into any system can be challenging: from ensuring your boards will meet performance needs in the most rugged conditions to creating a basic framework that will last despite growing radar system, EW & SIGINT application needs.
