-
Product
Non-Contacting Video Extensometer
AVE3
-
The AVE3 is Instron’s most advanced extensometer, engineered for high-precision, non-contact strain measurement across a wide range of mechanical tests—including tension, compression, and flexure. Its adaptable design accommodates various specimen types, sizes, and elongation ranges, making it ideal for everything from delicate films to robust metals. By eliminating the need for clip-on devices, the AVE3 streamlines setup and ensures uninterrupted data collection through specimen failure, even in high-energy break scenarios, such as composites. Compatible with environmental chambers and fluid baths, it supports non-ambient testing with ease. With compliance to ISO 9513 and ASTM E83 and a fast 500 Hz data rate, the AVE3 delivers reliable performance for demanding testing standards.
-
Product
Axial Extensometers
-
6 models in this group cover tension, compression and cyclic testingHuge variety of gauge lengths and measuring rangesCover temperatures from -265 to +200 °C (-450 to +400 °F)
-
Product
Miniature Averaging Axial Extensometers
Model 3442RA1
-
Jinan Testing Equipment IE Corporation
With gauge lengths of 1 and 2 inches (25 and 50 mm) and measuring ranges of 0.050 and 0.100 inches (1.2 and 2.5 mm), the Model 3442RA1 was designed for applications where tensile or compressive strength tests on small rock, concrete and other small compression samples is desired.
-
Product
Auto Calibration for Load & Extensiometer
-
Jinan Testing Equipment IE Corporation
TE electronic calibration module provides an easy way to calibrate load cell or extensometer and signal conditioning electronics without using a mechanical calibrator. It enables performing on-site electrical calibration and easy to periodically “spot check”, which will help ensure that the load cell and the extensometer and electronics are calibrated correctly.
-
Product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
-
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 4013 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Semi-automatic tensile testing machine
-
The controller of this testing machine automatically applies an appropriate load and puts the extensometer between the gauge lines, etc. after the sample is set. It provides measurement with high repeatability.
-
Product
Fracture Mechanics Clip-On Gages
Model 3541
-
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
High-Temperature Extensometers < 600 °C Capacitive
-
Instron® High-Temperature Extensometers are perfect for testing advanced composites, metals, polymers and other materials at elevated temperatures. This series incorporates a capacitive sensor that does not require any cooling. The extensometers come standard with a sensor conditioner unit providing a 0-10 V output with exceptionally low noise. These extensometers can be attached to round and flat specimens to perform tensile, compression, and cyclic tests.
-
Product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
-
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
Product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
-
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
Product
High Temperature Axial Extensometers
-
4 models cover a variety of applications for high temperature testing1 un-cooled model for use inside chambers up to 600 °C (1000 °F)Other models for use with split furnaces and induction heating, up to 1600 °C (2900 °F)
-
Product
Automatic Extensometer
SIE-560A/560SA
-
To determine the suitability of a material for an application where it is under load, measuring its elongation is important. Measuring elongation enables determination of the elastic modulus (reversible elongation in the elastic region) by measuring the small initial elongation range, and determination of elongation at specimen failure, by measuring larger irreversible elongation in the plastic region. Shimadzu’s SIE-560A series automatic extensometers accomplish both of these measurements with high accuracy, and provide automated functions that increase testing efficiency and test reproducibility. Ideal for testing a wide variety of materials, including metallic materials, plastics, and composites, the SIE-560A series complies with ISO 527, JIS K 7161, and ASTM D638 standards for plastics tensile testing. In addition, the SIE-560A series supports strain-rate controlled metallic material tensile testing measurements specified in ISO 6892, JIS Z 2241, and ASTM E4
-
Product
Rebar Coupler and Rebar Splice Extensometers
Model 3567
-
Jinan Testing Equipment IE Corporation
Extensometers for measuring elongation of rebar coupler, splicer, and sleeve assemblies. Use for tension, cyclic, slip, and differential elongation tests.
-
Product
Transverse (Diametral) Extensometers
Model 3575
-
Jinan Testing Equipment IE Corporation
Designed for general purpose transverse or diametral strain measurement on axially loaded specimens. This model may be used simultaneously with the model 3542 axial extensometer.
