PXI Chassis
See Also: Chassis, 3U PXI Chassis, 6U PXI Chassis, Portable PXI Chassis, ATE
-
Product
PXI 4 Slot BRIC 132x4 1-Pole (3 sub-cards)
40-562A-021-132X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
NI-9149, 8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783376-02
Chassis
8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9149 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9149, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
Product
Chassis - Control up to 16 Modules with as Many as 32 Two Pole Relays Per Module Allowing 1xN Multiplexers up to 1020x1, 2 Pole Muxes up to 512x1 or 2xN Matrix Configurations up to 256x2
JX/256-MF
Chassis
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
Product
VXI Chassis
Chassis
The first VXIbus specification was introduced to the test and measurement community in 1987 and was initially developed to provide a card-based instrumentation platform for applications that required high density and high performance. The platform continues to thrive today by leveraging off the original specifications which define the necessary physical (real estate/cooling) and electrical standards for demanding applications and has established itself as the ‘time-tested bus you can trust’ for requirements that must be supported in excess of ten-fifteen years.
-
Product
Chassis - up to Twelve 8x1 or 4x2 Modules & up to Six 8k Modules
HXV/96-MF
Chassis
These Chassis controls up to 12 8x1 modules, 12 4x2 modules, or up to 6 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
14-Slot Combination PXIe Chassis
GX7100e Series
Chassis
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Product
PXIe Full Hybrid Chassis, 18-Slot (Gen 2)
42-926-001
Chassis
Our 42-926 high-performance PXIe Chassis provides one PXIe system slot, one PXIe timing slot and 16 hybrid compatible slots for application flexibility. The chassis utilizes a single PCI segment with a dedicated PCIe-to-PCI bridge module for the hybrid slots. The PXI-specific high accuracy clocks and trigger signals are generated and controlled by an independent clock module attached to the rear of the backplane.
-
Product
cDAQ-9179, 14‑Slot, USB 3.0 CompactDAQ Chassis
783597-01
Chassis
14‑Slot, USB 3.0 CompactDAQ Chassis - The cDAQ‑9179 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements with the higher performance data streaming of USB 3.0. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9179 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
Product
Economical 4U Rack Mounted Industrial Chassis Supports ATX Industrial Motherboard
RK-620MB-L Series
Chassis
- Supports ATX industrial motherboards- Two external 5.25'' drive bays- Two USB type A connectors on front panel- 12cm two ball bearing cooling fan ( 103 CFM)- PS2 ATX power supply
-
Product
cPCI Serial Chassis 9 Slots
4U 50HP
Chassis
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 9 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 9 slot PCIe Gen3 backplane with single star topology, powered by a 300W cPCI Serial power supply.
-
Product
9U Dual System CompactPCI® Chassis with Redundant Power Supplies
cPCIS-3320/AC
Chassis
The cPCIS-3320 Series 9U Dual-System Platform is ideal for developing telecom applications focusing on media and signaling gateways, as well as telecom value-added services like Location Based Service (LBS), Ring Back Tone (RBT), and Multimedia Message Systems (MMS).
-
Product
cDAQ-9188 , 8‑Slot, Ethernet CompactDAQ Chassis
782824-01
Chassis
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
FPGA PXI Card
GX3601
FPGA PXI Card
The GX3601 is a 3U PXI FPGA card with 80, TTL buffered channels. The card is comprised of a GX3501 80 channel, TTL buffer expansion module and a GX3500 FPGA card.
-
Product
4-Slot GbE Industrial DAQ Chassis
iDAQ-974
Chassis
Giga-bit Ethernet data interface, supporting daisy chainWide range power inputLED status indicatorsPhysical ID switch for multiple module identification4 x iDAQ slots2 x programmable function pins for timing signals (trigger, clock) input/output
-
Product
2-slot CompactPCI® Rackmount Chassis
cPCIS-6130R
Chassis
The cPCIS-6130R Series subsystem is designed for Telecom Data Center and Enterprise applications requiring a low profile PICMG 2.0 R3.0 CompactPCI compliant chassis with PICMIG 2.1 R2.0 hot swap support. The chassis is 1U height and standard 19" rack mount width for 6U cPCI cards, has a 2-slot board space, a hot swap backplane, a 64-bit/66MHz cPCI bus, and provides rear I/O for 80mm RTMs.
-
Product
2U Rackmount Chassis For ATX/ MicroATX Motherboard With Low-Profile Rear Bracket
RK-270MB-LH
Chassis
- EIA RS-310C 19” Rackmount Standard - One 5.25'' drive bay and three 3.5'' drive bays- Supports 300W, 500W Flex ATX power supply- Support 7 low profile slots- Replaceable and easy-to-clean air filter- Front mounted fan module for easy maintenance
-
Product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782109-01
Synchronization Module
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module - The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified … synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
Product
NI-9147, 4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783496-01
Chassis
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
Product
Four Slot PXI/PXIe Full Hybrid ABex Chassis with up to PXIe x4 Connectivity on Each Slot
ABex PXIe Rack 04
Chassis
Ultra-Compact 2U ABex chassis with 4 slots. This variant is characterized by outstanding compactness and due to the directly integrated PXIe full hybrid backplane one achieves maximum performance at an attractive price. The first slot is reserved for a single slot PXIe controller. Either Konrad PXIe embedded controllers or MXI interfaces are supported.
-
Product
LXI Chassis Y Plugin - Y1 Y8 - Multi-Y Connection
65-110-103
Chassis
This Y1 Y8 plugin is for the 65-110A chassis. One of these plugins are required to be fitted to all 65-110A chassis assemblies to provide Y input connections.
-
Product
PCIe Gen3 x8 FMC Module
PXI Express Module
VITA 57.1 FMC HPC ConnectorPCIe Gen3/Gen2/Gen1 x8 Slot (upto 64Gbps)Single module supports both PCIe Root Port & EndpointM.2 Key-M NVMe slot with PCIe Gen3 x2 interface & SATA3.0 interfaceMIPI DSI & CSI Connector through LVDS IOs32Kb-EEPROM
-
Product
CompactDAQ Chassis
Chassis
CompactDAQ Chassis feature USB, Ethernet, or WiFi connectivity and come in multiple slot counts to provide the right amount of I/O for various applications. You use these models with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. CompactDAQ Chassis can include multiple general-purpose counters/timers that you can access through an installed, hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement. CompactDAQ Chassis also offer multiple timing engines, which allow you to run multiple hardware-timed operations simultaneously with independent rates for analog input.
-
Product
6-Slot LXI/USB Modular Chassis
60-106-001
Chassis
Pickering Interfaces’ 60-106-001 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. The chassis features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.This chassis is also available with built-in scan list sequencing and triggering (model 60-106-002).
-
Product
Chassis - up to Four 8x1 or 4x2 Modules, or up to Four 8k Modules in a 4 RU Chassis
HXV/32-MF
Chassis
These Chassis controls up to 4 8x1 modules, 4 4x2 modules, or up to 2 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
Chassis
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
Chassis - up to Sixteen 8x1 or 4x2 Modules & up to Eight 8k Modules
HXV/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 16 4x2 modules, or up to 8 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
6-slot PXIe Chassis
PXCe4006
Chassis
6-slot PXI Express chassis1 system slot, 1 PXI Express slot and4 PXI/PXI Express full hybrid peripheral slotsOptional: complex FPGA trigger controller with8 freely configurable trigger IOs on the rear sideVery compact 1U 19" designFour link PXI Express chassisEasily replaceable fan unit
-
Product
CompactPCI Chassis 3 Slots
1U 84HP
Chassis
Hartmann CompactPCI 1U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 3 slot 5V I/O 3U cPCI backplane for horizontal mounting of boards. This system is designed with enhanced EMC features.
-
Product
3U / 6U PXIe Chassis
Chassis
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
Product
CompactPCI Chassis 8 Slots
3U/84HP
Chassis
Hartmann CompactPCI 3U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides an 8 slot 3.3V or 5V I/O 3U cPCI backplane for vertical mounting of boards.
