Filter Results By:
Products
Applications
Manufacturers
-
product
ADSL Testers
The common used ADSL Tester is ADSL2+ Tester. It is an easy-to-use, hand-held advanced telecommunication tester that used for the installation, maintenance and measurement of ADSL2+ service. This tester supports the testing function such as parameter, error, DMM, PING that related to ADSL2+ service, user register authentication on the ADSL2+ user’s line side. It also directly enables the engineers to verify, troubleshoot and evaluate the ADSL2+ service. It is the right tool for the network test job.
-
product
ADSL / 2 / 2+ Handheld VoIP Tester
QuickTest 500
*Rapid Testing. The QuickTest 500 ADSL2+ Tester's automatic Service Verification Test Suite starts as soon as you switch on (results are typically obtained in less than 3 minutes)*Simple to use. Virtually no product training required with QuickTest 500 ADSL Tester*Configurable Pass / Fail Indicators on the LCD display and clearly presented in multi-colour LEDs on the front panel*No need to get a laptop out*Save and name up to 16 test results at any one time*Line Voltage LED indicates poor, missing or excessive Line Voltage*ADSL/2/2+ Test LEDs to indicate if ADSL Showtime achieved*In Service LED indicates problems with PPP or IP layer*LEDs to indicate problems with the Trained Line Rate, poor Noise Margin or excessive Line Attenuation
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Wiring Tester
WIZE
The testers can be used both in production and maintenance, as WIZE® is suitable for simple wiring tests and complex interconnect tests for full systems. WIZE®’s specifications make it compatible with the standard requirements used for testing in the aeronautics, space, rail and defence sectors or any other industry using wiring.
-
product
Armature Tester
Qingdao AIP Intelligent Instruments Co., Ltd
This tester is suitable for online or offline detection of various armature electrical properties, such as power tool motors, garden tools, vacuum cleaner motors, small household appliance motors, automobile motors, fitness equipment motors, permanent magnet micro-motors, etc. The tooling of the tester meets the requirements of arbitrary placement of the armature, and can automatically and accurately sort/track faulty solder joints; the equipment startup methods include buttons, remote control, and sliding cover; it meets the armature test of special processes such as double insulation, and automatically identifies solder joints, winding short circuit/open circuit , winding errors, poor welding and other problems; the tester can also automatically count the number of tests, the number of defectives and other data, which is convenient for quality management analysis.The tester test items mainly include:bar-to-bar resistance, diagonal resistance, welding resistance, insulation resistance, ac hi-pot, surge.
-
product
Hipot Tester
HVA Series
HVA systems detect faults in cable networks in a non-destructive yet efficient way and fulfill all the requirements of modern cable testing.
-
product
Power Tester
PS-200
It is important to keep your graphic cards powered, but you want to make sure that your graphic cards aren’t overpowered. Not all power supply units have power surge protection, so your graphic cards may be vulnerable to damages from over voltage or over current. Protect your graphic cards now with the new PS-200.
-
product
Solderability Tester
MUST 3
The MUST System 3 is the latest technological evolution of the original Multicore Universal Solderability Tester (MUST) that grandfathered all modern solderability test standards. It remains the unquestioned industry benchmark for solderability testing.
-
product
Receptacle Tester
RT500
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
product
CCTV Tester
M-IPC-200A
Fuzhou Metricu Technology Co Ltd
3.5 inch IP camera tester M-IPC-200A with analog, HD-TVI, HD-CVI, AHD
-
product
Validation Testers
M Series
The M Series line introduces a new class of massively parallel SerDes validation testers that are ideal for high-volume data collection and characterization. Constructed using a collection of Introspect Technology’s D Series modules that are operated seamlessly using the Introspect ESP software, these massively parallel testers are able to interface to high-speed devices in their entirety.
-
product
Electrical Tester
T5-600
The T5-600 Electrical Tester is a versatile troubleshooting tool you can carry to every job site. Use it to check voltage, continuity, and current, all with one compact, rugged tool. Just select volts, ohms, or current and the tester does the rest. For higher voltage applications check out the Fluke T5-1000.
-
product
Oscilloscope Tester
ScopeTester 5
ScopeTester 5 is 5-channel oscilloscope tester for PCs. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
product
Abrasion Testers
The measure of aggregate toughness and abrasion resistance such as crushing, degradation and disintegration.
-
product
Cable Testers
DMX ADAPTER
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
product
HD-TVI Tester, HD-CVI Tester, AHD Tester
M-IPC-300 series
Fuzhou Metricu Technology Co Ltd
4 inch IP camera tester
-
product
Diode Tester
FEC200E
Frothingham Electronics Corporation
The FEC200E is an automatic computer- controlled diode and rectifier tester. It is controlled by a standard PC-compatible computer running FreeDOS.
-
-
product
Vibration Testers
Analyzes vibration patterns within mechanical systems or individual components and structures to identify defects and evaluate the test object's overall condition.
-
product
Torque Tester
WDI series
New standard torque tester. Manage electric screwdrivers, manual torque screwdrivers, and wrenches with this one unit! WDI-10HR WDI-100HR WDI-250. THE CULMINATION OF 50 Years of Manufacturing TORQUE MEASURING TOOLS.
-
product
Torque Tester
DIS-IPS series (20CL/5C)
For managing various torque wrenches, torque drivers, and automatic/semi-automatic machines. The highly compact detector is ideal for automated line measurements. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. Efficient measurement is possible without unwinding work by "OW joint ".
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Cable Testers
CableJoG 512
CableJoG 512 provides a flexible testing system to suit individual customer requirements.The CableJoG 512 can test up to 512 individual connections of all manufacturers of connectors.
-
-
product
Cable Tester
The MapMaster™ mini detects faults and locations of RJ45 network cables. Good terminations, causes of faults and locations of cables are displayed on an LCD display. A set of five mapping remotes is included for locating cables terminated in wall jacks or patch panels. A built-in tone generator with 4 different tone combinations can be used with a tone probe to detect where a cable is routed and the location of the end of the cable.
