Filter Results By:
Products
Applications
Manufacturers
Cable Television
Community Antenna Television or. Community Access Television service.
-
product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
product
CATV RF Optical Receiver
L-RF-MN-RX
The QuestTel''s L-RF-MN-RX module optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications. It is perfect solution for the transport and distribution of CATV RF signals over fiber optic cable. The L-RF-MN-RX module housed in a small housing and have adjustable RF output level. May be used as a hand held device for testing, or placed at a customers premise for the reception of cable television services. The Receiver is designed to operate with a very low optical input level between the range of +3dBm to -12dBm.
-
product
Video RF Splitters
Analog Devices acts as a major supplier of video RF splitters and related technology such as CATV line drivers. Our high performance drivers and splitters enable the implementation of the most advanced cable modems and set top boxes on the market. Typical applications for our technology include multituner digital set top boxes, cable splitter modules, multituners/digital cable ready (DCR) televisions, and home gateways where traditional solutions require discrete passive splitter modules with separate fixed gain amplifiers.
-
product
Distribution Amplifier
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
product
Television Meters
Scope of meters: control and adjustment of networks of distribution receiving systems of television and radio broadcasting, individual elements of the network and other radio electronic devices. The range of manufactured devices is able to satisfy the requirements of almost any specialist involved in the installation and maintenance of cable television networks and individual television reception systems.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 2m
A050DM4-T-0A200
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Tinned Ends
A078HF4-T-0A100
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1.
-
product
50 Ohm BNC to BNC Cable Assembly
40-977-501-0.5m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
68-Pin VHDCI Cable Assembly, Male to Unterminated With Tinned Ends, 1m
A068VMR-T-6C100
The male cable assembly is suited for direct connection to various products using the 68 Way VHDCI connector.
-
product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Tinned Ends, 5A, 0.5m
A050FFR-T-0A050
This is a 0.5m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m
A050DF5-C-0A050
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Cable Assembly, 50-Pin SGMC, Female to Unterminated, Cut Ends, 5A, 0.5m
A050FFR-C-0A050
This is a 0.5m long female to unterminated 50-Pin SGMC cable assembly with ferrules and is constructed from 19/0.18 (21AWG) Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable, 0.5m
192061-0R5
Connects to DAQ devices and modules, terminal blocks, bare wires, or other accessories. The multifunction cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 96-pin SCSI, and 68-pin SCSI. Cable selection depends on the connector types and requirements of the hardware you’re connecting to and the environment in which you’re using the cable. Some cables are internally twisted and shielded to more effectively reject ambient noise than an ordinary shielded cable. These cables are designed to work with high-performance NI devices.
-
product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Tinned Ends, 1m
A025DF4-T-0A100
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
68-Pin VHDCI Cable Assembly, Male to Unterminated With Cut Ends, 1m
A068VMR-C-6C100
The male cable assembly is suited for direct connection to various products using the 68 Way VHDCI connector.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 1m, HV
A037DM5-T-HA100
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 200-Pin LFH, Female (Female Screwlocks) to 4x50-Pin IDC, Male, 0.5m
40-971B-200-0.5m-FM
This female rear exit to male ribbon 0.5m long cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to its mating connector by female screwlocks.
-
product
Cable Assembly, 50-Pin D-Type, Male to Female, 1m HV, Exit Towards Pin 1
A050DM5-050DF5-HA100
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, Receiver, Mini Coax, 20", 17 SMB Plugs
540053010107
Cable Assembly, Receiver, Mini Coax, 20", 17 SMB Plugs
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 1m, HV
A037DF4-C-HA100
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable, 10 Pos Combicon to Pigtail, 1 Meter
190656-01
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m
A037DM5-T-0A050
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable
192061-05
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable - The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths.
-
product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m
A015DF4-T-0A050
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 2m HV, Exit Towards Pin 1
A050DF5-T-HA200
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
540265010207
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
-
product
Cable Assembly, Receiver, 20", QuadraPaddle, to 192-Pin DIN & 3 68-Pin VHDCI
540351010140
Cable Assembly, Receiver, 20", QuadraPaddle, to 192-Pin DIN & 3 68-Pin VHDCI
-
product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 2m
A1604FR-T-0A200
A range of DIN41612 cable assemblies with unterminated connections on one end. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
Cable Assembly, Receiver, TriPaddle, 36", 200 Pin Male LFH w/ M3 Jackscrews
540105010205
Cable Assembly, Receiver, TriPaddle, 36", 200 Pin Male LFH w/ M3 Jackscrews
-
product
51-Pin REDEL High Voltage Cable Assembly, Male To Unterminated, Ferrules, 0.25A, 1m, 29 Wires
A051KMR-F-HA100-29
This is a 1m long male to unterminated 51-Pin REDEL high voltage cable assembly with ferrules constructed from 19/38 (26AWG) Silver Plated Copper Wire with FEP insulation. Latch clips areprovided to secure the connector to associated product.
