Filter Results By:
Products
Applications
Manufacturers
Circuit
-
product
Printed Circuit Board Testing Solutions
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
product
Mezzanine System
5085
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
product
Vectorbords
VECTOR Electronics and Technology, Inc.
General purpose pre-punched insulating punchboard is available in variety of grid patterns shown below for assembling circuit components. Vectorbord® is available in FR4 epoxy glass, FR2 phenolic, CEM-1 epoxy glass composite and FR4 HiTg 170°C materials. Vectorbord® listed below is unplated copper clad on one side, both sides or unclad with no copper layer on either side.
-
product
Current Limiting Resistors
Current Limiting Resistors are designed for limiting the flow of current to some predetermined value and are used mainly to to keep flowing current within certain intervals while controlling the circuit.
-
product
T3DSO Passive Probe, 350 MHz, 1X/10X, 1 MOhm/10 MOhm, 300V/600V
T3PP350
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
product
Advanced Design System (ADS) Core
W2200BP
Advanced Design System (ADS) is the flagship product from Keysight EEsof EDA, the technology and innovation leader in high-frequency, mixed-signal electronic design automation (EDA). It is the only design simulation platform that enables the co-design of IC, package and board in high-frequency and hi-speed applications. ADS seamlessly integrates system, circuit, and full 3D electromagnetic simulation with Keysight's test instrumentation to perform single pass successful electronic designs repeatedly.
-
product
Armature Tester
Qingdao AIP Intelligent Instruments Co., Ltd
This tester is suitable for online or offline detection of various armature electrical properties, such as power tool motors, garden tools, vacuum cleaner motors, small household appliance motors, automobile motors, fitness equipment motors, permanent magnet micro-motors, etc. The tooling of the tester meets the requirements of arbitrary placement of the armature, and can automatically and accurately sort/track faulty solder joints; the equipment startup methods include buttons, remote control, and sliding cover; it meets the armature test of special processes such as double insulation, and automatically identifies solder joints, winding short circuit/open circuit , winding errors, poor welding and other problems; the tester can also automatically count the number of tests, the number of defectives and other data, which is convenient for quality management analysis.The tester test items mainly include:bar-to-bar resistance, diagonal resistance, welding resistance, insulation resistance, ac hi-pot, surge.
-
product
Voltage Converters
Made from marine-grade aluminium extrusions or heavy-gauge aluminium sheet metal. Powder-coated or anodized, and use stainless fittings throughout Fitted with robust circuit boards using expensive heavy-gauge copper conductors, designed by Analytic Systems' engineers and assembled in our plant.Models are available to step-up, step-down, stabilize or isolate DC power over a range of 12 to 360 volts. No matter which unit you need, these easy-to-install Voltage Converters will give you many years of reliability.
-
product
Portable Test Bench For Single Phase Energy Meter
SY 2100
Hong Kong Songyang Industrial Ltd.
Anthropomorphize design, Large size LCD display, easy operation. High stability, good reliability. Reasonable internal structure. Compliance with IEC736.ISO9001 certificate. Automatic switchover of voltage or current output to protect equipment when voltage circuit short or current circuit open and alarm display on LCD
-
product
Peak Voltage Measurement
In high voltage measurement technology, the peak value, or the effective value, of the voltage is determined in accordance with VDE 0432 or IECV 60060. The peak voltage measuring device from MPS Mess- & Prüfsysteme GmbH can measure these two values in connection with a high voltage divider (capacitive or resistive). In the event of flashovers in the high-voltage circuit, this is indicated in the SMG.
-
product
6-24V DC Heavy Duty Automotive Circuit Tester
1175
Circuit tester with 1.5M of heavy duty cable and earth (crocodile) clip. Insulated contact point to prevent accidental shorting. Testing range 6-24V DC
-
product
Force Sensor Elements
The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.
-
product
PXI RTD Simulator Module, 20 Channel, PT500
40-263-102
The 40-263-102 is a 20-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
8 Channels Thermocouple, LV A/D
TC1
A thermocouple is a temperature-measuring device typically consisting of two dissimilar conductors that contact each other at one or more spots. It produces a voltage when the temperature of one of the spots differs from the reference temperature on other parts of the circuit. Thermocouple temperature sensors are widely used for measurement and control, and can also convert a temperature gradient into electricity.
-
product
Test Connector Components
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
product
Circbord
8022
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges.
-
product
Digital Earth Resistance Tester
8PK-ST1520
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
product
High Current Transformers
High Current Transformer is designed to elevate and check the temperature of the conductors at high current levels, in order to simulate the current loading conditions found in electrical circuits. High Current Transformer is designed as an open type transformer that uses the test object as its secondary coil or has 1 or 2-turn self secondary winding. The conductors cores' temperature depends on the short-circuit high current caused by the test object. According to the current going through the test object, the test temperature of the conductor will change. The loop temperature is measured by a thermocouple probe which is directly connected to conductor.
-
product
Insulation & Multifunction Tester (LCD Display)
4102 MF
Standard Electric Works Co., Ltd
● Measures Insulation Resistance, voltage (AC-DC) measurements● Automatic hold facility.● Continuity test with a short circuit current of minimum 200mA.● MOV and Gas Arrester Testing.● Energy conservation is feature.● EnerSave™ limits the test duration to about 10 Seconds to save energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
-
product
860MHz CATV Indoor Bi-directional Amplifier
Hangzhou Softel Optic Co., Ltd.
SA801H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network.
-
product
RF Functional Test Fixtures
EMC Technologies’ design team has developed a variety of test adaptors and test stations for testing RF circuit assemblies and microwave sub-assemblies.
-
product
DC DC Converter Models
These versatile DC-DC Converters are ideally suited for powering a wide variety of analog and digital circuitry, such as op amps, logic and microprocessors. They may be mounted directly on a printed circuit board for OEM applications, or installed in a socket for developmental and small quantity requirements.
-
product
500 MHz Passive Probe, 5mm, 10:1, 10 MOhm
PP025-1
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
product
Analog Simulator
MPLAB® Mindi™
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
product
RF and Microwave Circulators
Chengdu KeyLink Microwave Technology Co., Ltd.
RF Circulators from KeyLink Microwave are passive 3-port microwave devices designed to provide isolation between transmit and receive signals for radar, satellite communication, and telecommunication applications. These microwave circulators can control the signal direction and flow inside an RF circuit. KeyLink provides broadband RF circulators spanning the frequency range of 1 GHz to 18 GHz in varying bandwidths, tailored to cover all standard and popular bands commonly used throughout the market place.
-
product
Timer Relays
A Timer Relay is a combination of an electromechanical output relay and a control circuit. The contacts will open or close before or after a pre-selected, timed interval.
-
product
6-24V Heavy Duty Circuit Tester
1672
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems.1. Locate short, ground and open circuit.2. Make it easy to find out where current is present.3. The most essential for troubleshooting automotive electrical systems.4. Checks series-parallel switch and solenoid on tractor-trailer start systems.
-
product
Antenna Noise Canceller
ANC-4
The ANC-4 is an rf device that eliminates or reduces power line noise, BPL noise, computer noise, TV-generated interference, and other types of electrical noise. The ANC-4 unit connects right to the antenna connector of the receiver or transceiver to cancel locally generated noise before it gets into the receiver and affects the receiver AGC circuits.
-
product
Auto Contact Resistance Tester
KVHL
KV Hipot Power Test Equipment Co.,Ltd
KVHL Auto contact Resistance Tester with advanced large power switch power technology ang electric circuit is a special measurement instrument for testing the contact resistance of high/low switchs, cable wires and welds.
-
product
Optical Transmitter
ST1310-XX
Hangzhou Softel Optic Co., Ltd.
ST1310-XX Optical Transmitter adopts high linearity ORTOL DFB laser, build-in perfect pre-distortion adjustment circuit and laser APC,ATC closed loop control circuit. All the operating parameters are controlled by micro-processor, The LCD screen on the front panel can display relative operating status and the fault information.
