Filter Results By:
Products
Applications
Manufacturers
DWDM
Dense Wavelength Division Multiplexing
-
product
100GHz/200GHz DWDM Module in LGX Box
Flyin Optronics’ 100GHz/200 GHz dense wavelength division multiplexer (DWDM module) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add and drop at the ITU wavelengths. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
1310nm/1550nm Fused Biconical Taper WDM
SWD1315
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai SWD1315 single mode DWDM adopt fused bi-conical taper technical with low insertion loss, channel flatness features. Mainly used in optical network 1310nm and 1550nm combination and halve.
-
product
Dense Wavelength-Division Multiplexing
DWDM
Dense Wavelength-Division Multiplexing (DWDM) entails transmitting signals at multiple closely spaced wavelengths through the same fiber. ACP offers DWDMs with channel spacing of 200, 100, or 50GHz; corresponding to about 1.6nm, 0.8nm, or 0.4nm respectively.
-
product
Optical Performance Monitor
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
product
40-CH 100G Thermal AWG
Flyin’s 40 channel 100G Thermal AWG(100G TAWG) is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the TAWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the TAWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. We can also offer different product packages, including special metal box and 19” 1U rackmount.
-
product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
12/24 CH Insertion Loss/Return Loss Automatic Testing System
CA3201
UC INSTRUMENTS CA3201 12/24 CH INSERTION LOSS/RETURN LOSS AUTOMATIC TESTING SYSTEM is special designed for MPO/MTP fiber cable and multi-channel fiber optical devices like PLC device. It also can be easy changed into AWG DWDM devices testing system ifwe change 1310 /1550 nm light source into UC INSTRUMENTS’ tunable laser source.
-
product
Optical Wavelength Meters
Optical wavelength meter that uses a He-Ne laser as reference wavelength and employs the Michelson interferometer method, providing high-accuracy measurement. It can measure emission center frequencies of LDs for DWDM with high resolution and accuracy.The 8471 even provides a high sampling rate of 10 times per second, and is suitable for oscillation wavelength adjustment. In addition, its deviation display function allows wavelength variation to be measured with high resolution and accuracy.
-
product
Attenuators
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
product
C-Band DWDM Line Amplifier EDFA (WLA-C)
HWA4200 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4200 series, is designed for C-Band 44 waves or 88 waves DWDM system design Line Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
product
(100×130×19mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM04
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM04 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
Fiber Identifier
OFI-20A
OFI-20A can detect optical signal presence, type and direction anywhere on fibers during optical network deployment, maintenance and troubleshooting. With non-destructive macro-bend detection technology, it introduces no damage to tested fiber or interference to the service on fiber. OFI-20A is able to identify wide-spectrum signals (such as signals in CATV system) and can be used in SONET/SDH & DWDM systems tests.
-
product
C-Band DWDM Pre-Amplifier EDFA (WPA-C)
HWA4300 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4300 series, is designed for C-Band 44 waves or 88 waves DWDM system design Pre-Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
product
200GHz DWDM Module(4,8,16 Channel)
Flyin Optronics’ 200GHz dense wavelength division multiplexer (DWDM) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add and drop at the ITU wavelengths. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
100GHz DWDM Optical Add/Drop Multiplexer (CATV Overlay Multiplexer)
OADM-1001-VOA (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OADM-1001-VOA is an optical Add-Drop multiplexer with 100GHz channel interval. It is based on mature thin film filter technology, sealed with metal shell, and featured with low insertion loss, high isolation, wide channel and flexible configuration. It is the ideal device to Add(insertion Add)/Drop(Tape-out Drop) a specific wavelength(OADM) in optical fiber DWDM system. OADM-1001-VOA configures a manual-adjust optical attenuation, for adjust the equilibrium the optical power between insert channel and main signal channel, which is conveniently used for VOD overlay in CATV system.
-
product
(100×130×19mm) C-Band DWDM Booster EDFA Module
WBA4100-FM04
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM04 series used 100 x 130 x 19mm compact package, is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
product
(100×130×19mm) C-Band DWDM Pre-Amplifier EDFA Module
WPA4300-FM04
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WPA4300-FM04 series with 100 × 130 × 19mm Compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 wave wave DWDM system applications.
-
product
Erbium Doped Fiber Amplifier
EDFA
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
product
(70×90×15mm) C-Band DWDM Full Function Booster EDFA Module
WBA4100-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WBA4100-FM02 series used 70 x 90 x 15mm MSA compact package, is a digital control circuit of DWDM power amplifier function module. Products using the most excellent optical properties, electronic control technology and complete software function is most advanced, wide wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Application for C-Band 44 wave or the 88 wave of DWDM system.
-
product
950~2400MHz DVB-S 4 ways SAT-IF DWDM Optical Transmitter & Receiver
HDBS-4000DW
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDBS-4000DW series, combine 4 pieces C-Band, 100GHz, ITU standard wavelength SAT-If optical transmitter, or optical receiver to one chassis, through DWDM, Make 4 ways optical MUX (TX) or DEMUX (RX), through one fiber, used in transmitting 4 ways different polarization SAT-IF signal of one satellite VL, VH, HL, HH with high performance. Installation flexibility.
-
product
Passive Devices
Fiber Splitters, Muxes, CWDM, DWDM, WDM, PON, Fiber Jumpers, Fiber Attenuators.
-
product
DWDM High Power DFB Buttterfly Laser
CA1782-XXX-XX-BT
The CA1782-XXX-XX-BT DWDM High Power DFB Buttterfly Laser component is characterized for use as a CW optical source in CATV and DWDM networks. The CA1782-XXX-XX-BT is dc-coupled with a built-in TEC, thermistor, and monitor photodiode. The device is mounted in a 14-pin, OC-48 pinout compatible butterfly package with the optical isolator mounted on the TEC. The CA1782-XXX-XX-BT incorporates a high efficiency coupling scheme to deliver 40 mW, 50 mW, 63 mW and 100 mW of CW optical power.
-
product
100GHz Optical Add/Drop Multiplexer
OADM-1000 (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OADM-1000 100GHz optical add/drop multiplexer based on the mature thin-film filter technology, metal seal. With so much great features like low insertion loss, high isolation, wide pass band, flexible configuration and so on. This is the ideal parts for used in DWDM system Add/Drop special wavelength.
-
product
Multi Wavelength DWDM Gain Flattened Variable Gain EDFA
MX4500 Series
This EDFA is ideal for long distance DWDM or CWDM transmissions and may be used as a Line Amplifier, Pre-Amplifier, and Booster Amplifier.
-
product
Standard Optical Interleaver
An innovative technique for expanding the number of channels per fiber involves an optical device, called an optical interleaver. For example, in most DWDM equipment, the standard channel spacing is 100 GHz. But spacing the signal-carrying frequencies every 50 or even 25 GHz can double or even quadruple the number of channels per fiber. This job is accomplished by an optical interleaver. Such a device takes two multiplexed signals with 100-GHz spacing and interleaves them, creating a DWDM signal with channels spaced 50 GHz apart. The process can be repeated, creating even denser composite signals with 25-GHz or 12.5-GHz spacing. The signals at the receiving end are recovered with the same devices used as splitters or optical de-interleavers. Thus, devices and/or networks can be upgraded without requiring that all devices be upgraded, or network bandwidth can be increased.
-
product
Hybrid Raman/Er-doped Fiber Amplifier
HFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600nm.
-
product
Splitters, WDM, CWDM, DWDM
OPTOKON manufactures an extensive range of reliable and field-proven fiber optic components designed to increase system capacity. To be cost-effective, these compact solutions assist service providers, dark fiber developers, and enterprises to increase fiber capacity while keeping growth flexibility and high ROI. By providing the necessary platforms for a smooth and effective transition into optical networks they fulfill high bandwidth needs while cutting implementation, upkeep, and growth costs.
-
product
Multi-channel Optical Power Meter For Swept Test System
MPM-210HMPM-211, 212, 213, 215
Our MPM-210H is ideal for IL, WDL and PDL measurement of multi-port optical components including Dense Wavelength Division Multiplexing (DWDM), Arrayed Waveguide Gratings（AWG) , Wavelength Selective Switches (WSS) and more. When combined with our TSL-Series laser equipped with a power monitor output, the MPM-210H allows the user to complete real-time high precision IL measurements.
-
product
C-Band Separate Raman Fiber Amplifier
RFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
CATV Separate Raman Amplifier
RFA4000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Amplifier is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. Raman amplifier is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
