Filter Results By:
Products
Applications
Manufacturers
Interrupters
-
product
32-CH Isolated DIO Card
LPCIe-7230
ADLINK LPCIe-7230 is 32-CH isolated input and/or card. It provides a 2,500 C optical isolation protection. Two wide input range of the LPCIe-7230 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The LPCIe-7230 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automations applications. The LPCIe-7230 also provides two interrupt sources on digital input channels, which are easily user configurable.
-
product
32 Channel Analog Comparator Module
DP-VXI-5106
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can be programmed to generate a VXI bus interrupt or can be masked through software. An Interrupt is generated on an individual channel basis or on a group basis. Front panel outputs of buffered TTL and a 2-CO relay contact is available for every group (4 outputs total each). Also, a common buffered TTL interrupt output and a common 2-CO relay contact is also available at the facia providing extensive flexibility in application engineering.This module is an ideal device for GO / NO-GO testing in Test Stand Automation where important signals must be continuously monitored for system shut down purposes and safety inter-lock implementation. The hardware implementation in the Comparator module provides high-speed throughput and reliable inter-lock implementation. The interrupt out signal can be further wired as trigger signals for pre and post trigger analysis of signal data for post acquisition detailing.Each channel provides a Window Comparator implementation and a Level Comparator implementation. The configuration is programmable through software and the alarm can be generated if the signal is within the window or outside the window. Similarly, a high and low limit can be set and a trigger is generated if the signal exceeds the high limit or drops below the low limit.
-
product
RTXCview System Trace and Profiling Tool
RTXCview
RTXCview is a system trace tool designed to work in tight integration with the RTXC Quadros RTOS family. This powerful visualization tool gives you deep visibility into system performance and behavior. Typical embedded system development tools such as debuggers can only provide a static view of your system, focusing on code-level details. RTXCview complements this view by providing a system-level view, showing how tasks and interrupts interact with the RTXC kernel.
-
product
DDoS Detection and Mitigation
Increasingly, business is done online. This increases the risk of exposure to costly service interruptions caused by cyberattacks. Distributed Denial of Service (DDoS) attacks have emerged as one of the most common and impactful attack vectors aimed at business networks. Today, DDoS attacks account for 40% of all cybersecurity incidents, with some organisations facing multiple attacks per day. With the average throughput of volumetric attacks rising by over 3X in the last decade, DDoS prevention has become essential for any organisation that relies on its network infrastructure to do business.
-
product
Multifunction Power & Harmonics Analyzer
KM 2100 / KM 2200
Kusam Electrical Industries Limited
• Volts / Amps. / Hertz, Dips & Swell, Power / Energy, Unbalance, Monitor, Scope, Harmonic, Logger & Interruption functions. (KM 2200)• Inter Harmonics, Transient Voltage, Inrush Current, Flicker function not available in KM 2200.• Frequency upto 400Hz (KM 2100); 50 / 60Hz (KM 2200)• Single-phase 2W / Single-phase 3W / 3-phase 3W / 3-phase 4W.• Flash memory 128MB• TF Card 8G Memory Card for long-term measuring data storage. • Support USB port to connect to PC and analyze the data / screen shots copied by U-disk.• Support LAN port to make the remote control available, transfer the measuring data.
-
product
PCIe Digital I/O Board, 16 Optically Isolated I/O Channels, 24V
APCIE-1516
8 digital inputs, 24 V, isolated15 interruptible inputs8 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
Current Measurement Probes
Comprehensive line of clamp-on current probes covers the entire spectrum of applications, from electrical panels to substations. AEMC Current Probes measure current without interrupting the circuit under test and extend the measuring capabilities of DMMs, recorders, power meters, and loggers. The numerous jaw sizes are designed to accommodate a wide variety of conductor diameters and ranges. Available for AC or DC measurements.
-
product
Uninterruptible Power Supplies
Mains interruptions can have serious consequences. Do not take any chances, you can rely on our uninterruptible power supply (UPS). A UPS supplies power even in the event of mains failure and protects your system against supply interruptions. We offer UPS solutions for DC and AC applications where the functionality and design are optimally tailored to the requirements of various different industries.
-
product
Analyzer Probe
Net-200
The NET-200 B analyzer probe is an integral part of the NET-xTVMS, the real-time monitoring of IPTV services quality. Intended for locations at the core, edge, subheadend, etc., the NET-200B is designed to function autonomously for an extended period of time should communication with the NET-ESVR Enterprise Server be interrupted. The NET-200B is running under stable and safe Linux OS on server class computers, powered by AC or DC sources, with optional power redundancy.
-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
product
Voltage Sag Generator
SKS-1132GTB
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
product
IEC61000-4-11 Voltage Dips And Interruptions Simulator Generator
VDS-1120DX
Shenzhen Chuangxin Instruments Co., Ltd.
The voltage dip and interruptions generator is specially designed according to the characteristics and requirements of EMS measurement under a sudden reduction or interruption of the voltage at a point, CSS61000-11/ CSS61000-11T used a big LCD in both English and Chinese operating interface. They have more fine performance such as high reliability, convenient operation, and full meet the standard requirements of IEC 61000-4-11, EN 61000-4-11 and GB/T17626.11
-
product
Network Interface Controller
SPIDAR®
User interface and data acquisition embedded on the NIC:1. Any device with Wi-Fi can be used to change settings or view data collection2. No data collection interruption or data loss occurs if connection to PC or device is interrupted. No reduction in speed compared to running a single system. Daisy-chain NICs to deploy any number of GPR systems simultaneously; build Multi-frequency systems or Multi-channel Array systems Advanced timing control to ensure no interference between GPR systems
-
product
SparkFun 6 Degrees Of Freedom Breakout
LSM6DSO (Qwiic)
The SparkFun LSM6DSO 6 Degrees of Freedom Breakout is an accelerometer and gyroscope sensor with a giant 9kB FIFO buffer and embedded processing interrupt functions. Due to the capabilities and low cost of the LSM6DSO we've created this small breakout board just for you! Each LSM6DSO breakout has been designed to be super-flexible and can be configured specifically for many applications. With the LSM6DSO breakout you will be able to detect shocks, tilt, motion, taps, count steps, and even read the temperature!
-
product
PC/104-Plus And PCI-104 8-Port RS-232 Serial Communication
P104-COM232-8 and 104I-COM232-8
The P104-COM232-8 (PC/104-Plus) and 104I-COM232-8 (PCI-104) are PC/104-based eight channel RS-232 communication peripherals. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD). A 460Kb/s rate is guaranteed for all channels with up to 3K Ohm 1000pF loads. All interrupts may be monitored at a 32-bit status register. Each UART has both a 64 byte transmit and a 64 byte receive FIFO.
-
product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
Acquisition Of 8 Displacement Transducers
APCI-3701-8
PCI interface to the 32-bit data bus Acquisition of 16 or 8 inductive displacement transducers (Half Bridge, LVDT) 8 or 16 input channels ± 10 V 16-bit resolution Measuring frequency up to 100 kHz Conversion can be triggered through software End of conversion can be inquired through software Possibility of interrupt through digital input channels (when a data or a time value is exceeded) PCI-DMA access Onboard FIFO buffers Sequence RAM 16 isolated digital I/O, 24 V Software operation Supported inductive transducers for APCI-3701Standard board APCI-3701-8 or APCI-3701-16Transducer type:
-
product
Developers' Toolkits
If you are a hardware developer, using RapidDriver Explorer with just a couple of clicks, you can easily start testing and debugging your USB, ISA, PCI or Parallel Port device. You do not have to perform any additional steps - everything is already done!If you are a software developer, you can write your own application with the help of RapidDriver Developer, TVicHW32 or TVicPort without writing a device driver and being a DDK expert - we have already built-in generic device drivers for you! Our toolkits include many test examples on direct port i/o access, interrupt handling, physical memory access, reading specific hardware registers and USB pipes to help you getting started. We also allow redistribution of drivers and DLL's as part of your software without having to pay royalties.For the software developers, we also offer an option to purchase the drivers and DLL source code. The source code can be directly edited and compiled with MS Visual C/C++ or with the DDK "build" utility.Not sure what product to choose? Compare them by features or contact us.
-
product
Digital I/O Board, 32 Isolated I/O Channels, 24V
APCIE-1500
The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.
-
product
Multifunctional Meter
AEM-DR
Provide high accuracy measurement, display and remote communication of single phase & three phase parameters (V, A, P, Q, S, PF, Hz, Kwh). Multicircuit design and relay output modular expansion design decrease the overall cost and make the functionality more flexible. All monitored data is available via a RS485 serial , for the needs in energy management, alarming, and remote controlling. Embedded flash memory for Data-Logging can avoid any data missing once the communication is interrupted. Moreover, its ultra compact size DIN-rail mounting makes itself mountable in virtually any panel, enclosure or indoor Cabinet.
-
product
8 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-8-8
- 8 electromechanical relays with change-over contacts The PCI-Express 8 relay board APCIe-2200-8-8 has 8 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
product
Load-to-Line Jumpers
200
TESCO’s Load-to-Line Jumpers (Catalog No. 200) allows the utility to perform meter maintenance without interruption of service to the downstream occupant. TESCO bypass jumpers are rated for 200 amps continuous duty and are made from a durable 1/8″ thick tin-plated copper with a durable insulating material covering everything except the blades.
-
product
SparkFun Triple Axis Accelerometer Breakout
MMA8452Q
This breakout board makes it easy to use the tiny MMA8452Q accelerometer in your project. The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings relieving the host processor from continuously polling data.
-
product
UHF Multi-Frequency Belt-Pack IFB Receiver
IFBR1B
Wireless IFB (interruptible fold back) systems are used for talent cueing and crew communications in broadcast and motion picture production. In other cases, the IFB system is used by directors and other management to monitor program audio during a production. The IFBR1B receiver provides simplicity and flexibility in a package that is intuitive for untrained users to operate. Despite its tiny size, the new IFBR1B receiver offers excellent performance on par with all of Lectrosonics’ IFB products.
-
product
Transformer Winding Resistance Meters
RMO TT Series
The Tap Changer Analyzer & Winding Ohmmeter of the RMO-TT series is designed for winding resistance measurement of inductive objects, and for a tap changer analysis. The RMO-TT series is based on the state of the art technology, using the most advanced switch mode technology available today. The RMO-TT instruments are accurate (0,1%), powerful (up to 100 A) and still portable. The Instruments generate a true DC ripple free current with automatically regulated measurement and discharging circuit. RMO-TT instruments can perform a simple, quick and reliable transformer on-load tap changer condition assessment. This series of instruments enable measurements of a winding resistance in every tap position, current ripple values (percentage of a current drop during a tap change) and transition times during the tap changes. Problems with a connection, contacts, and selector/diverter switch operation (tap change with interruption) can be detected with these measurements.
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
Digital Input Board, 32 Isolated Channels, 5V
APCI-1032-5
32 digital inputs, 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
product
Compact Type 4 Safety Beam Sensor
ST4
Panasonic Industrial Devices Sales Company of America
Panasonic's concept of connecting 6 sets of Sensor heads to 1 Controller in series offers maximum flexibility to solve a wide range of safety applications. Just configure exactly the number of Sensor heads and controllers required to protect the area in question, e.g. small openings or irregularly shaped spaces impractical for Safety Light Curtains. A beam interruption indicator is incorporated in both the emitter and receiver to indicate operation and assist with beam alignment.
