Filter Results By:
Products
Applications
Manufacturers
-
product
L Band Splitter, DC Block All Ports
PD5182
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
L Band Splitter, DC Block All Ports
PD5162
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
L-Band Red/Blue-Band Pass MWDM
WD1616/R, WD1616/B
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1616/R, WD1616/B is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to the combination and separation of L-Band, Red-Band (1589~1603nm) and Blue-Band (1570~1584nm).
-
product
FMC L-Band RF Receiver
Sundance Multiprocessor Technology Ltd.
The Creonic L-band RF receiver FMC card allows to receive RF signals between 925 and 2,250 MHz. It is ideally suited for satellite communication with standard satellite dishes since it includes a DiSEqC driver IC for LNB controlling. The board allows to build receivers with symbol rates of up to 100 Msymbols/s. Due to the low-pin-count (LPC) FMC connector it can be used with any FMC carrier board that supports VADJ=1.8V. The card will be available from Q2/2017.
-
product
DC Blocking L-Band Splitter Combiner
PD5960
INSTOCK Wireless Components, Inc
PD5960 is an IP67 outdoor, weather resistant, DC blocking, six way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5960 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 6 way power divider input rating tables for additional power handling info.
-
product
L Band Splitter, DC Block All Ports
PD5142
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 57791
- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - XMC
Model 71791
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O
-
product
L Band Satellite over Fiber
Transport L Band signals from Satellite Dish to Receiver over Fiber Cable
-
product
L Band Splitter, DC Block All Ports
PD5122
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
product
IP67 DC Blocking L-Band Splitter
PD5021
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portOutdoor Weatherproof ConstructionTri Alloy N Type Female (Jack) 50 Ohm
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 57891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
IP67 DC Blocking L-Band Splitter
PD5131
INSTOCK Wireless Components, Inc
PD5131 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5131 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
product
L-Band ASE Light Source
ASE6000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ASE6000 series is L-Band ASE light source with featured with high stability and high output. It is mainly applied for testing of L-Band optical components and optical communication equipments as well as Fiber Optical Sensor etc. Huatai ASE6000 has three types of exterior structure, suitable for different customer’ requirements.
-
product
950~2600MHz Satellite L-Band PIN Optical Receiver
HRS-26S/P
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-26S/P optical receiver, adopting high-sensitivity PIN detector, receiving sensitivity is -22dBm, typical value: -13dBm. It can receive analogue and digital signal on satellite antenna LNB with the frequency of 950~2600MHz, It can be compatible with any FTTx PON to realize combination of Direct Broadcasting Satellite (DBS)with Internet and FTTH, it can also be used for L-Band uplink/downlink of satellite communication.
-
product
L-Band RF Tuner and 2-Channel 400 MHz A/D
Model 78891
Accepts RF signals from 925 MHz to 2175 MHz, Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm, Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz
-
product
DC Blocking L-Band Splitters, RF Power Dividers
INSTOCK Wireless Components, Inc
INSTOCK Wireless offers DC-blocking power divider / combiners optimized for L-band power splitting applications. Standard configuration includes DC pass on one port to power a remotely located active antenna. Additional models available blocking DC to all ports. All models pass the 10 MHz reference signal through all ports.
-
product
L Band Splitter, DC Block All Ports
PD5042
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
product
C+L Band Broadband Light Source
S-103
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
-
product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - PCIe
Model 78791
Model 78791 is a member of the Onyx® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. It is suitable for connection directly to an L-band signal for SATCOM and communications systems.
-
product
Optical Spectrum Analyzers
Low cost, fast spectral measurement in a compact module with built-in analysis including SMSR, OSNR and spectral width. Targeted wavelengths for specific applications in O band, C band and L band.
-
product
Modulators
ZMOD-X1
Antenna Technology Communications, Inc.
The ZMOD-X1 modulator series is an all inclusive unit that is loaded with features most needed by broadcasters. In it's most basic form, the unit comes with DVBS, DVBS2 and 8PSK modulation schemes, IF output, L band output and ASI input all as standard features. 16 APSK modulation and IP input are provided as options. Taking mobile and portable systems in mind, the unit comes with clear and user friendly front panel control. Size and weight are significantly less than any unit on the market. The unit can also be monitored and controlled using any web browser.
-
product
Optical Performance Monitor
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
product
Waveguide Receiver Protector
The continuous evolution of radar systems creates an ever more complex RF power environment in which sensitive receivers must operate and survive. Teledyne limiters deliver vital protection for a wide range of receivers, providing protection from L-Band through to Ka-Band (1 - 40GHz) and peak power levels up to 1MW with unparalleled low insertion loss levels.
-
product
IP67 DC Blocking L-Band Splitter
PD5031
INSTOCK Wireless Components, Inc
PD5031 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5031 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
product
Attenuators
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
product
Advanced Identify Friend Or Foe (IFF) System
Model MD500L IFF
Kratos Defense & Security Solutions, Inc.
The Model MD500L IFF Transponder is an L-Band augmentation device ideally suited for use in aerial target drones, unmanned vehicles, and cruise missiles as a radar enhancement device that provides automatic radar identification in response to interrogations from L-Band IFF and Air Traffic Control (ATC) radars. It also supports Mode C (altitude reporting) operation.
-
product
Dual L-Band RF Tuner and 4-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 58791
- Accepts RF Signals from 925 MHz to 2175 MHz- Two programmable LNAs handle L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Four FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Airborne Receivers & Bit Synchronizers
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
