Filter Results By:
Products
Applications
Manufacturers
Mezzanines
Is the stacking of cards into a single card that then plugs into the computer bus or data path.
-
product
Mezzanine System
5081
The 5081 provides four channels of 12 bit digital to analog voltage output, with multiple single ended output ranges. Each channel is software selectable for 0 to +5V, 0 to +10V, +/-2.5V, +/-5V, +/-10V or -2.5 to 7.5V ranges. The outputs reset to 0.0 volts on power up.
-
product
Mezzanine System
5093
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
product
Mezzanine System
5658
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
-
product
Mezzanine System
5174
The 5174 provides two major functions, serving as a precision Voltage Controlled oscillator board and a variable frequency source board. These features can be use together or independently. As a variable frequency source, the 5174 provides a high-resolution variable clock source that is based upon a reference clock supplied by the ECM carrier.
-
product
Voltage Meter
MN6I
The mezzanine is designed to measure instantaneous voltage values through six isolated channels with differential inputs.
-
product
CPCI Dual Industry Pack Carrier
CPCI-6713-2 IP
The board consists of private SDRAM and Flash memory attached to the 300 MHz, TMS320C6713B floating point DSP. An FPGA provides the timing and control. Peripherals include a serial port and connectors for IP mezzanine boards. Flash memory is available for downloading programs into a nonvolatile memory. A PCIbus connector provides the interface to the host computer.
-
product
Multi I/O FMC Module
FMC155
The FMC155 is an FPGA Mezzanine Card (FMC) per VITA 57.1 standard, offering a small footprint and allowing for general-purpose I/O expansion. The FMC155 provides sixteen LVDS input/outputs, eight RS-485/422 RX plus eight RS-485/422 TX, and sixteen single-ended +3.3 V input/outputs.
-
product
PC-based DSP Systems
PCI / cPCI : 32bit, 33MHz6201 or 6701 DSP16MB SDRAM1MB SBSRAM15+ Mezzanine I/O Cards (see OMNIBUS)Open bus for custom I/OFIFOPort external data port
-
product
XMC-to-PCI Express Adapter
7988
The Technobox, Inc. P/N 7988 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 7988 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
product
Resistance Meter
MT8-4L
М-module МТ8-4Л is a mezzanine module designed to measure the resistance of resistive sensors using a four-wire measurement circuit in eight channels (eight-channel digitizer). М-module МТ8-4Л is installed on the carrier of mezzanines - module НМ-М and is connected to it via a local information highway. Up to four m-modules of various types can be installed on the NM-M module. The NM-M module, together with the m-modules installed on it, forms a VXI module of size C-1 and is used to create information measuring VXI systems.
-
product
ADC 12-bit @ 2.6 GSPS and DAC 14-bit @ 5.6 GSPS, FMC
FMC216
The FMC216 is an FPGA Mezzanine Card (FMC) per VITA 57 specification. The FMC216 utilizes AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a DAC AD9129 providing 14-bit conversion rates of up to 5.6 GSPS. The analog input/output, digital output, clock and trigger interfaces of the FMC216 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
product
Mezzanine Carrier
HMNS AXIe-0
The HMNS AXIe-0 module is a carrier of mezzanine modules made in the AXIe-0 standard. The module ensures the functioning of various modules installed in it, made in the form of mezzanines. The HMNS AXIe-0 module is intended for use as a carrier of mezzanines in multichannel systems for collecting/issuing information of both digital and analog types.
-
product
PMC-to-PCI Express Adapter (PCIe/PCI-e)
5243
Our PMC-to-PCI Express Adapter (PCIe/PCI-e) 1X (5243) permits the use of a single-wide PMC module in a 1x PCIe slot. The A and C rows of a 96-pin DIN connector, located toward the rear of the board, connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
product
Single Board Computers
SBC
Our single board computers (SBCs) include versatile mezzanine sites for custom I/O processing and off-board processing. Each processing node is equipped with the best compute power from their respective device generation and are fully interoperable with similar form-factor, OSA and fabric building blocks for low-risk processing subsystem pre-integration.
-
product
Mini Module
COMeT10-3900
The COMeT10-3900 is an industrial COM Express® Type 10 Mini module with an Intel Atom® E3900 processor. This low power, industrial module was designed and manufactured in the USA. The small form factor module is designed as a processor mezzanine that can be plugged onto a carrier board that contains user-specific I/O requirements.
-
product
Single CMC size PCI Mezzanine Card
PMC SyncClock32
Brandywine Communication’s model PMC-SyncClock32 is a compact PCI Mezzanine Card (PMC) that precisely synchronizes the time on VME cards or provide accurate GPS synchronized time to the host motherboard. The 32-bit interface provides time from microseconds through years.
-
product
Accelerators
Our GPGPU embedded processing accelerators are powered by NVIDIA or AMD devices that are picked for their long service life support and suitability for embedded processing applications. Each GPU processor is mounted on a rugged mezzanine for upgradability.
-
product
Mezzanine FMC
FMC-516
Curtiss-Wright Defense Solutions
The FMC-516 provides the low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of data delivered to the FPGA host through the FMC-516.
-
product
Voltage Meter
МН32СМ
The mezzanine module (mezzanine) МН32СМ is designed to measure instantaneous voltage values over thirty two two-wire differential channels.
-
product
Mezzanine PMC
PMC-E2001
Curtiss-Wright Defense Solutions
The PMC-E2001 keeps low speed, high quality analog IO simple and takes care of ruggedization for youThe PMC-E2001 combines analog input and output channels and is an application-ready module engineered to perform precise using sigma-delta devices for waveform generation and reconstruction for audio and acoustic applications.
-
product
Mezzanine FMC
FMC-518
Curtiss-Wright Defense Solutions
The FMC-518 provides high-speed, low latency, high-performance functionality necessary for applications such as Signal Intelligence (SIGINT), Electronic Warfare (EW) and RADAR (including beamforming) through the density, speed and resolution of the data delivered to the FPGA host through the FMC-518.
-
product
Graphics Display Processor
XMC-4740
Curtiss-Wright Defense Solutions
The XMC-4740 is a SWaP-optimized XMC mezzanine that delivers high-performance video processing and display. Equipped with a cutting-edge, rugged AMD Radeon GPU that delivers next generation capability with similar power consumption to previous generations, the XMC-4740 maximizes processing performance without requiring its own dedicated slot.
-
product
6U VPX Single Board Computer
VPX6-195
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
product
8-Channel ADC Module
FMC108
Sundance Multiprocessor Technology Ltd.
The FMC108 is an eight-channel ADC FMC (FPGA Mezzanine Card) which is fully compliant with the VITA 57.1-2010 standard. The FMC108 card provides eight A/D 14-bit 250MSPS channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC108 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled compliant. The board is also available with Mil-I-46058c compliant Conformal Coating.
-
product
FPGA Mezzanine Card (FMC)
FMC DEL
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) created to produce pulses delayed by a user-programmed value with respect to the input trigger pulse. It has 4 output channels and one input trigger. The delay from the trigger input to each of the outputs can be set independently in a range from 600 ns to 120 seconds. It is implemented using a dedicated time-to-digital converter IC from the European company Acam.
-
product
Mezzanine System
5188
ECM P/N 5188 provides an AD8109 crosspoint switch for analog or digital signals with 250MHz of Bandwidth. For single ended applications 8 inputs can be connected up to 8 outputs in any configuration.
-
product
4-slot LXI Chassis
MezaBox-4 LXI
MezaBOX-4 LXI is a device that ensures the functioning of various mezzanine modules (up to 4) installed in it, under the control of a personal computer via USB2.0 or ETHERNET 10/100 Base T (local area network) interfaces of a personal computer. MezaBOX-4 LXI is intended for use as a mezzanine carrier in multichannel systems for collecting / issuing information, both digital and analog.
-
product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
product
XMC Mezzanine Module 2 x SFP+
DN3-SHARK XMC 2.0
The DN3-SHARK is a is a XMC standard mezzanine card, equipped with a dual port 10Gbps Ethernet controller.
-
product
Strain Gauge Module
МТМ8
Mezzanine module (mezzanine) МТМ8 is designed to measure the output signal of strain gauges. The mezzanine can be used with any bridge sensors (pressure, force, etc.).
