Filter Results By:
Products
Applications
Manufacturers
Open Short
Pinpoint open circuits.
-
product
Economy Mechanical Calibration Kit, DC To 3 GHz, Type-F, 75 Ohm
85039B
The Keysight 85039B calibration kit, with option M0F, contains male and female type-F open, short, and load standards. This calibration kit works with all 75 ohm network analyzers and test sets for measurement of devices with 75 ohm type-F connectors. The kit also includes type-N to type-F adapters. More economical versions of this kit are available by ordering option 00F for the female standards only, or option 00M for the male standards only. This kit is specified from dc to 3 GHz.
-
product
Cable Fault Locator
FaultCaster
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
product
Impedance Standards and Calibrators
Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.
-
product
Network Toner & Probe Kit
MT-7028
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
LAN Cable Tester
21-6568-00
The Handheld Lan Cable Tester is an intelligent continuity tester for LAN cables, Phone cable and Coaxial cable. Open, short and misswiring are also tested. It provides the installers an ease of use which keeps you from wasting time through complex menus.
-
product
6GHz SMA Calibration Kits
CAL-SMA-6B
The CAL-SMA-6B Basic calibration kit provides the elements for performing Open–Short–Load and Through calibrations for one and two port VNA measurements.
-
product
Rack Mount Audio/Lighting/Network Cable Tester
AudioJog Rack 8
There are 2 rows of 9 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
Cable Fault Locators
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
product
LCD Multifunction Cable Tester
MT-7059
Display test result on large LCD for easy reading and cable status identificationThe wire can be tracked directly in connection with Ethernet service, router, and PC terminalValidate and troubleshoot wiring on RJ11/RJ45 cables, Coaxial cable, USB cable, IEEE 1394 cableTest cable status for continuity, shorts, opens,miswired, crossover9 different tones selection for convenience use under different environment conditionAll installation and maintenance fields of telecommunication, networking, cable TV and more
-
product
LAN Cable Tester
LAN-1
The LAN-1 Cable Tester is designed for testing opens, shorts and miswired cable installations. It is designed to work with various data cables and connectors. This cable tester provides a quick go / no-go LED display of the wiring and connection of item under test. You can either step through the test cable wiring one at a time or have the unit automatically pulse through the pin-outs and display the results.
-
product
Cable Testers
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)
CK058F
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Network Cable Tester
AVJoG Rack
*A single box solution for testing AV cables. *Easy to use with only one button operation. *Detects Open, Short and Crossed circuits. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *40+ preprogrammed cable types.
-
product
Multi-Modular Cable Tester
MT-7051N
Tests RJ45 TIA568A/B (AT&T 258A), 10 Base-T, Token ring, RJ-11/ RJ-12 USOC and Coaxial BNC cable.Automatically check cable for continuity, short, open and crossed wire pairs.Coaxial cable port indentifies cable conditions including shorts, shield opens and center conductor breaks.Main unit and remote allow one person testing.Power source: DC 9V BatteryDimension: 102x106x28 (mm)Cable not include
-
product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
product
Cable Testers
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
product
4-in-1 OSLT Calibration Kit, DC to 18 GHz, Type-N (f) 50 Ohm
CK519A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Motor Winding Ohmmeter
RMO-M Series
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
product
4-In-1 OSLT Mechanical Calibration Kit, DC To 26.5 GHz, Type-3.5 Mm (m) 50 Ohm
85520A
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit.
-
product
12V Circuit Tester With LED Polarity Indicator
1658
Peaceful Thriving Enterprise Co Ltd
Checks open or short circuits on 12V automotive computer circuits and all primary automotive electrical circuits. Safely tests standard primary automotive circuits and on-board computer controlled electrical system without damaging the micro-processor.
-
product
ELECTRONIC CIRCUIT TRACER
PPECT3000
*Locate short and open circuits without having to remove plastic panels, molding and carpet*Traces shorts and open wires with visual navigation and sound indicators*Pinpoint shorts, open circuits, switches and breaks in wires
-
product
Network Tester
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
product
Multimeter Network Tester
VA16
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Network Cable test (RJ45): Tests for open circuits, shorts, miswires, reversals, and split pairs SHIELD detection tests a cabl
-
product
Stand Alone Low Voltage Testers
Low voltage testers are a special type of device used to identify opens and shorts in applications that are driven on low voltages.
-
product
Telemetry Transmitter
TT22 Series
Systems Engineering & Management Company
The TT22 series of 0.25W telemetry transmitters are designed to transmit data in the frequency bands covering 1710-1850 MHz or 2185-2485 MHz. These transmitters are true FM, modular, all solid state and are protected for operation into any VSWR, without damage, including open or short circuit.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Automated DC Parametric Curve Tracer
MultiTrace
MultiTrace curve tracer is a mid-sized benchtop model supporting pin counts from 216-625 pins and includes the PGA-625 fixture as a standard interface. MultiTrace supports a wide range of test applications: Failure analysis, Reliability testing, Counterfeit device analysis, Nondestructive electrical counterfeit test, Opens, shorts leakage testing (OSL), Post decap electrical inspection, Optical fault localization, ESD testing, Latch-up testing, Supply current measurements, and more!
-
product
Cal Kit, 4-in-1 OSLT, DC To 26.5 GHz, 3.5 Mm(f)
85521A
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
