Filter Results By:
Products
Applications
Manufacturers
Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
product
Ethernet To Parallel Digital Interfaces
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
product
Ethernet To Parallel Digital Interfaces
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
product
Serial Parallel Interface
Model 2303
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
product
GPIB Parallel Interface
Model 4803
* 4803 Board provides 40 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual GPIB headers support connections to a GPIB Connector/Address Switch Assembly or to a GPIB Flat Ribbon Cable Assembly.* Optional Relay Driver board drives 24-40 relays.
-
product
Ethernet To Parallel Digital Interface Boards
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
product
Parallel Interface Voltage Output D/A Converters
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
product
1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
GPIB Parallel Interface
Model 4813
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Optional Relay Driver boards add 64 or 128 Relay Drivers.
-
product
Programmable Gain Amplifiers
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
product
Bipolar/FET/Diode Dual Head Production Test System
36XX
Two test stations on the 3600E and 3601E systems. Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes and darlingtons. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3602E or 3603E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
product
5 Mega Pixel Parallel Camera Module
e-CAM52A_5640_MOD
The e-CAM52A_5640_MOD is a Parallel Camera Module from e-con systems featuring Omnivision OV5640 image sensor. Any processor system like I.MX6, OMAP4430, OMAP4460, OMAP35x, AM37x, DM37x that has a Parallel interface can integrate the e-CAM52A_5640_MOD.
-
product
Ethernet Parallel Interface
Model 8013
* Provides 128 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has a horizontal Ethernet connector and 150-pin Digital IO connector on the component side. * Mates to Relay Driver Boards with 64 or 128 Relay Drivers.* Mates to 115650 Connector Board with 4 flat ribbon headers.
-
product
TRF Manager 9
Configuration by using a PC, this is one of the major TRF generator attribute. Instruments have factory settings suitable for common applications and contain the most popular test patterns. But many users want to customize the setup or set the instrument according to specificic application requirements. They also may want to adjust parameters, that cannot be accessed by any other way. That is what TRF Manager 9 (optional software pack) can do. And much more! Pattern generators of the TRF-498 and 598 series use a parallel interface for connection with PC. Basic setup can be realized by using Pattern Manager, free software downloadable from our site. For advanced settings there is available TRF Manager 3 software. For more detailed information see the TRF-498 and TRF-598 section, please.
-
product
Camera Link Translators
CLT-303
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
product
Serial And Parallel Port For PCIe
DTA-2142
Serial and parallel interfaces for ASI and SD-SDI, supporting multiple electrical standards including M-LVDS and LVTTL. Clock rates up to 108MHz are supported.
-
product
Single Head Component Testers
34XX
Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes, darlingtons and matched dual transistors. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3402E or 3403E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
product
GPIB Parallel Interface
Model 4823B
* Provides 56 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Available with DIN connector on circuit side for piggyback mounting.
-
product
Serial Parallel Interface
Model 2313
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
product
GPIB Digital Interface
Model 4863
ICS's 4863 GPIB Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
e-CAM1M_CU10630_MOD - 1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
0 Hz/DC to 14 GHz, Single-Pole, Four-Throw MEMS Switch With Integrated Driver
ADGM1304
The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).
-
product
Ethernet Parallel Interface
Model 8003
* Provides 40 high-power TTL I/O lines.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* Standard board has vertical Ethernet and Digital IO connector on the component side. * Optional Relay Driver board adds 4, 32 or 40 Relay Drivers. • Apply regulated 5 Vdc power through the Digital IO connector.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
Real-Time Clock (RTC) ICs
ST offers a wide portfolio of real-time clock (RTC) ICs with parallel or serial interface, including ultra-low-power devices and the world’s smallest package with embedded crystal. Our devices offer many value-added features such as supervisory functions that include alarm, battery switchover, and reset as well as special features with time stamp, anti-tamper for secure applications and an integrated audio section.
-
product
Serial To Digital Interface MiniBox™
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
Camera Modules
e-con Systems Camera Modules come with parallel & MIPI interfaces. Our CMOS camera modules will be effective in any application or environment because of their versatility and wide range of options. Embedded camera module can be interfaced to processors like Tegra K1, i.MX6, DM3730, OMAP. Further to these HD camera modules, e-con offers evaluation boards with these camera modules interfaced to various development boards featuring these processors. We provide Omnivision Camera Module & Aptina Camera Module (ON Semiconductor) with CMOS Sensors.
-
product
GPIB to Parallel Printer Interface
Model 4892B
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
product
Serial To Digital Interface MiniBox™
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
PXI LIN Interface Module
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
