Filter Results By:
Products
Applications
Manufacturers
Polarization Mode Dispersion
Polarization Mode Dispersion
-
product
Polarization Maintaining Fiber Components
OZ Optics offers a broad range of polarization maintaining components, patchcords, and connectors designed to resolve polarization problems, which are becoming increasingly important in today's higher speed and more complex mesh optical networks. By maintaining the polarization of the signal at its source, our polarization maintaining components minimize polarization mode dispersion and eliminate the effect of polarization dependent loss thereby increasing the quality of the signal that is transmitted throughout the network.
-
product
Measurement System
2800
The 2800 Chromatic Dispersion Measurement System provides fast, accurate measurements of chromatic dispersion and length of all types of single-mode optical fibers. Easy to use Windows-based software provides all industry standard calculation techniques for the determination of zero dispersion wavelength and dispersion slope. Options are available for the measurement of Polarization Mode Dispersion (PMD) and Fiber Strain.
-
product
Polarization Conditioners
High-speed software controlled polarization control and polarization scrambling with broad wavelength coverage, low insertion loss and back reflection.
-
product
Polarisation Mode Dispersion
PMD500
PMD500 is our polarisation mode dispersion (PMD) measurement system available in two PMD measurement methods, designed to produce accurate measurements quickly and with confidence.
-
product
Dispersion
Dispersions are often used in latex wall paints, which can thus be diluted with water. The homogenity of a dispersion depends on size and weight of particles. To determine the size of particles the use of a Fineness of Grind gauge or grindometer is needed. For proper mixing and / or stirring a variety of laboratory and industrial tools are available depending on volume or capacity.
-
product
Polarity Tester
PT5
PT5 Polarity Tester supporting testing of up to 24 single-mode or multimode fiber MPO or ribbon cables.
-
product
Polarity Tester
PT-1
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
product
Dual-USB3 Polarization Cameras
Celera P Series
Standard digital monochrome sensors capture light intensity and wavelength for each pixel: however, some applications require the inspection of polarized light to get relevant information.Instead of using external polarizing filters, Alkeria developed CELERA P, a new camera model featuring a special polarization image sensor.Thanks to its unique array of polarizer filters overlaid on top of the sensor's pixel array, CELERA P gets rid of all the external polarizing filters, combining the ease-of-use of the Alkeria USB3 cameras with the advanced capabilities of polarization imaging and unique FusionView feature.
-
product
Optical Polarization and Dispersion Solutions
Test & measurement capabilities for analyzing polarization properties of optical signals are indispensable in todays optical R&D-labs and manufacturing floors. The Keysight N778x Polarization Analysis and Control series offers high speed instruments for high performance characterization and verification of optical components and sub-systems.
-
product
Polarization Maintaining Collimator
Zhongke Rayzer Optical Technology Co.,Ltd
The basic element for in-line PM fiber optics components, such as PM Isolator, PM FWDM, PM Filter Coupler and PM Circulator. It has high extinction ratio, low insertion and high return loss. The unique processing and high quality AR coating also enable this collimator tohandle high power.
-
product
Polarizing Beamsplitter (PBS)
Polarizing beamssplitters split randomly polarized beams into two orthogonal, linearly polarized components. S-polarized light is reflected at a 90 degree angle while P-polarized light is transmitted. Polarizing beamsplitters come in cube form, but custom geometries are available.
-
product
TRMS Multimeter with VFD Mode
FLIR DM66
The DM66 digital multimeter is ideal for automation field service or electronics technicians, providing a comprehensive feature set including low impedance (LoZ) mode, frequency, diode, capacitance, and a Type K thermocouple input for temperature measurement. The multimeter combines rich features, precise measurements, and quality construction into a tool of exceptional value. Easy to use and built to last, the DM66 offers long-term stability for everyday use.
-
product
Dispersive X-ray Fluorescence Spectrometer
SPECTRO MIDEX
SPECTRO Analytical Instruments GmbH
The SPECTRO MIDEX is known to be an all-round talent for the fast, non-destructive analysis of small spots and the rapid mapping of large surfaces (up 233x160 mm, 9.2x6.3’’) in research and development as well is in compliance screening applications as many elemental analysis tasks in industry, research and the sciences require a non-destructive measuring system that is extremely sensitive and offers a small measuring spot.
-
product
Polarisation Mode Field Diameter
MA500
MA500 is our polarisation mode field diameter (MFD) and effective area (Aeff) measurement system, specially designed to measure large effective area and high NA single mode fibers with its enhanced dynamic range and high-resolution scanning optics.
-
product
MPO/MTP Polarity Testing Machine
Anfkom International Co.,Limited
12 Channel or 24 channel optional. One key button exchange, no need speical order and design 24 channel equipmentsSupport the 12/ 24 channel fan shape line detectionShort testing time.7″ color screen display, testing result are intutive and clear.Compatible with 9/125,50/125,62.5/125 fiberdetect unqualified have warning voice prompt, reduce misjudgement rateSupport custom 12 channels/24 channels fiber optic patch cable wire sequencethe data do not disappear when power supply drop.
-
product
Energy Dispersive X-ray Fluorescence Spectroscopy Systems
Energy Dispersive X-ray Fluorescence Spectroscopy Systems
-
product
Multi-angle Polarized Light Scattering Measurements
LISST-VSF
In-situ measurements of P 11, P12 and P22 elements of scattering Mueller matrix, (P11 is VSF) from 15-150º.VSF (P11) only at small angles, 0.05 to 10º in 32 logarithmic steps in angles.Only two detectors employed with absolute radiant sensitivity (A/W) calibration.Beam attenuation measured with optics similar to our LISST-100X.Roving Eyeball™ optics permit 1-degree resolution in angles between 15 -150º.Sampling rate at 3 seconds per measurement set (involves 3 turns of Roving Eyeball with unpolarized, vertical, and horizontal polarized laser).Daylight rejection by laser modulation.Dynamic range in VSF measurements extended via laser power modulation.Data from small and large angles in a single data stream, including depth and temperature.
-
product
Polarization Tester
Polarization Tester is used to measure the stress value of optical glass, glass products and other optical materials, and is widely used in pharmaceutical companies, glass products factories and laboratories.
-
product
Polarity & Burn in Test Systems
Our polarity and burn-in test systems are available for components such as multilayer, disc type or hollow ceramics.
-
product
Polarization Controller and Scrambler - MATRIQ
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
-
product
Polarization Maintaining Fused Wavelength Division Multiplexer (
Zhongke Rayzer Optical Technology Co.,Ltd
Polarization Maintaining Fused WavelengthDivision Multiplexer product, has thecharacteristics of low insertion loss, high handing power, high extinction ratio and double-axis operation. It is mainly used in the fields of polarization-maintaining fiber laser, polarization-maintaining amplifier, polarization-maintainingsensing system and scientific research application.
-
product
Tube-Above Wavelength Dispersive X-ray Fluorescence Spectrometer
ZSX Primus IV
As a tube-above sequential wavelength dispersive X-ray fluorescence spectrometer, the new Rigaku ZSX Primus IV delivers rapid quantitative determination of major and minor atomic elements, from beryllium (Be) through uranium (U), in a wide variety of sample types — with minimal standards. ZSX Guidance supports you in all aspects of measurement and data analysis. Can accurate analysis only be performed by experts ? No — that is in the past. ZSX Guidance software, with the built-in XRF expertise and know-how of skilled experts, takes care of sophisticated settings. Operators simply input basic information about samples, analysis components and standard composition. Measured lines with the least overlap, optimum backgrounds and correction parameters (including line overlaps) are automatically set with aid of qualitative spectra.
-
product
Energy Dispersive Spectroscopy (EDS) Detector Technology
EDS
The Element SDD is a solutions based detector, which excels at basic analysis. Focused primarily on serving the needs of the industrial market segment, it provides application specific software and analysis that can quickly provide answers in the industrial environment.
-
product
Common Mode Chokes
Common Mode Chokes, as the name implies, are designed to attenuate and filter common mode noise within an electric system. The key parameters for a common mode choke are the current rating (to ensure the part does not overheat within the application), the impedance versus frequency (to ensure it is optimized to attenuate the desired frequencies), the isolation voltage (to ensure it meets board level requirements between the line and neutral phases) and safety isolation (to ensure it meets the safety requirements of the end-application). It is important to remember that common mode chokes cannot saturate in the application (under normal use) as they are designed to ensure that the line and return currents are balanced.
-
product
Dispersion Compensating Fiber
Dispersion compensating fiber from M2 Optics is used for correcting dispersion effects created over distances within G.652 single mode optical fibers. Offered in a 19" chassis for rack or benchtop use, these high quality testing platforms are easy to work with and provide consistent, repeatable results.
-
-
product
Energy Dispersive X-ray Fluorescence (ED-XRF) Spectrometer
XEPOS
SPECTRO Analytical Instruments GmbH
The new SPECTRO XEPOS spectrometer represents a quantum leap in energy dispersive X-ray fluorescence technology. It provides breakthrough advances in multi-elemental analysis of major, minor, and trace element concentrations. New developments in excitation and detection deliver outstanding sensitivity and detection limits yielding remarkable gains in precision and accuracy. The amazing SPECTRO XEPOS excels at critical tasks from rapid screening analysis to precise product quality control. Apply it for at-line processing in a variety of industries, for geology and mining, for environmental and waste monitoring, and for research and academia.
-
product
Energy Dispersive X-ray Fluorescence Spectrometer
Pharmaceutical Elemental Impurities Analysis System
Control of Elemental Impurities in Pharmaceuticals In the pharmaceutical industry, the analysis of elemental impurities is necessary to ensure the safety of pharmaceuticals. In December 2014, the "Guideline for Elemental Impurities" (Q3D) was issued by the International Council for Harmonisation of Technical Requirements for Pharmaceuticals for Human Use (ICH), consisting of representatives from Europe, the U.S. and Japan. In Japan, the "Guideline for Elemental Impurities in Drug Products" (PFSB/ELD Notification 0930 #4 from the Ministry of Health, Labour and Welfare) was issued, and will be applied to new drug products submitted for approval after April 1 2017. For 24 elements categorized in Class 1 to Class 3, residual quantities in pharmaceutical drug products must be controlled within permissible limits. Although ICP-AES and ICP-MS are used for precise analysis of elemental impurities, X-ray fluorescence spectrometers can be used as an alternative analysis method. This is because they can quantitatively and qualitatively analyze a variety of elements nondestructively, and without chemical pretreatment, unlike ICP-AES and ICP-MS systems. The X-ray fluorescence spectrometry has been adopted as a general method of analysis in the U.S Pharmacopeia and the European Pharmacopoeia. (USP<735>, Ph.Eur.2.2.37)
-
product
Dual Wavelength Single Mode Light Source
FiberLink 6654
The Fiberlink 6654 Dual Wavelength Single Mode Light Source is a cost effective, compact, handheld light source. The temperature compensated outputs are calibrated to couple -10dBm of optical power into single mode fiber.
